Power Input Prediction in Agitated Gas‐Liquid Contactors with Non‐coalescent Batch

Volumetric mass transfer coefficients, k_La, just as power input are considered as essential parameters for mechanically agitated gas‐liquid contactors in relation to their optimization and design. The knowledge of power input is crucial for the prediction of other mass transfer characteristics. A power input correlation is created for the industrial design of the process with a non‐coalescent batch that would be appropriate for a broad range of operational conditions. The recommended resulting correlation is able to predict the power input for impellers in industrial‐scale design for a significant scope of operational conditions.     

Compensation of voltage disturbances using PEMFC supported Dynamic Voltage Restorer

The continuity of supply and quality of power are the two main significant aspects of today’s power delivery system. The Dynamic Voltage Restorer (DVR) is a series connected custom power device which improves the quality of power delivered to the consumers. This paper deals with the effectual exploitation of DVR for interconnecting the proton exchange membrane fuel cell (PEMFC) stack to the grid based on optimized proportional integral (PI) and fuzzy logic (FL) Controller. The real coded Genetic algorithm (GA) is used to optimize the PI controller parameters. The PEMFC operated boost converter is used to boost up the fuel cell output voltage to balance the DC side necessities of the voltage source converter (VSC). The proposed DVR provides balanced and unbalanced voltage sag/swell compensation, harmonic reduction as well as an active power injection to the grid. The designed method also protects the sensitive loads from source side power quality disturbances including short term interruption. In addition, the harmonic compensation performance of the proposed work is validated by comparing with the results of the H^∞ controller based DVR under medium level voltage condition. The simulation results from MATLAB/SIMULINK are discussed to prove the effectiveness of the planned method.     

Effect of 100 KeV Ar+ ion beam irradiation on ZnO thin films – Influence of morphology vis-a-vis electrode/electrolyte interface and its impact on photoelectrochemical water splitting

The present study attempts quantitative determination of changes in the morphological surface features viz. fractal dimension, lower and upper cut off length scale through Power Spectral Density analysis prior to and after irradiation of 100 KeV Ar⁺ ion beam at incidence angles of 0°, 40° and 60° on ZnO thin films. All the unirradiated and irradiated samples are subjected to photoelectrochemical characterization and a correlation between photoelectrochemical performance and morphological parameters is established. Sample irradiated at 40° angle at the fluence of 5 × 10¹⁶ ions/cm² is found to possess maximum fractal dimension of 2.72, lower and upper cut off length scale of 3.16 nm and 63.00 nm respectively. This sample exhibits maximum photocurrent density of 3.19 mA/cm² and applied bias photon-to-current efficiency of 1.12% at 1.23 V/RHE. Hydrogen gas collected for duration of 1 h for the same sample was ~4.83 mLcm^?2.     

Physicochemical and thermophysical properties of CaO–TiO2–SiO2–Na3AlF6 system based electrode coating for AUSC power plant

The aim of this study is to investigate the physicochemical and thermophysical properties of CaO–TiO₂–SiO₂–Na₃AlF₆ based electrode coating developed for the welding of advanced ultra-supercritical (AUSC) thermal power plant components. The extreme vertices approach has been used to create twenty-six electrode coating compositions. Various physicochemical and thermophysical properties were characterized using experiments. The coating properties are essential in ensuring sound weld with desirable in-service performance. The developed coating's structural behavior was analyzed using Fourier transformation infrared spectroscopy (FTIR) and X-ray diffraction (XRD). In addition, regression analysis was carried out to evaluate the influence of coating constituents. Individual constituents and their interaction were found to have a prominent role in influencing the physicochemical and thermophysical properties.     

PSO优化多核RVM的模拟电路故障预测

针对模拟电路健康管理的特点，提出了一种基于PSO优化多核RVM的模拟电路故障预测方法。利用参数分析得到电路的输出频域响应作为特征，计算其与电路无故障标准响应的欧氏距离来表征电路元件健康值，将多个核函数线性组合，并用PSO优化多核RVM参数后的模型实现对各个时间点元件的健康值变化轨迹进行预测。仿真结果表明，该方法在小样本情况下，预测效果优于单一核函数的RVM模型，适用于健康管理中实时预测，具有较好的实用性。     

Rogowski coil current transducer compensation method for harmonic active power error

In the harmonic active power measurement, the highest uncertainties are generally introduced by the current and voltage transducers. In a previous paper, the authors showed that the current transformer (CT) can introduce significant errors in such measurement, especially if the phase shift between voltage and current is close to ±90°. In such condition the errors on harmonic power measurement are mainly due to the CT phase displacement. This paper shows that better results can be achieved with more linear transducers, such as the Rogowski coil current transducers (RCCTs), whose metrological performance in distorted condition can be improved, by means of a proper compensation method. The proposed method for RCCTs compensation is based on the frequency response and it allows to reduce the errors on harmonic power measurement, also for phase shift close to ±90°. The study is supported by several experimental tests.     

Improved synergetic excitation control for transient stability enhancement and voltage regulation of power systems

This paper proposes decentralized improved synergetic excitation controllers (ISEC) for synchronous generators to enhance transient stability and obtain satisfactory voltage regulation performance of power systems. Each generator is considered as a subsystem, for which an ISEC is designed. According to the control objectives, a manifold, which is a linear combination of the deviation of generator terminal voltage, rotor speed and active power, is chosen for the design of ISEC. Compared with the conventional synergetic excitation controller (CSEC), a parameter adaptation scheme is proposed for updating the controller parameter online in order to improve the transient stability and voltage regulation performance simultaneously under various operating conditions. Case studies are undertaken on a single-machine infinite-bus power system and a two-area four-machine power system, respectively. Simulation results show the ISEC can provide better damping and voltage regulation performance, compared with the CSEC without parameter adaptation scheme and the conventional power system stabilizer.     

High-voltage and low specific on-resistance power UMOSFET using P and N type columns

For the first time, we present the unique features exhibited by power 4H–SiC UMOSFET in which N and P type columns (NPC) in the drift region are incorporated to improve the breakdown voltage, the specific on-resistance, and the total lateral cell pitch. The P-type column creates a potential barrier in the drift region of the proposed structure for increasing the breakdown voltage and the N-type column reduces the specific on-resistance. Also, the JFET effects reduce and so the total lateral cell pitch will decrease. In the NPC-UMOSFET, the electric field crowding reduces due to the created potential barrier by the NPC regions and causes more uniform electric field distribution in the structure. Using two dimensional simulations, the breakdown voltage and the specific on-resistance of the proposed structure are investigated for the columns parameters in comparison with a conventional UMOSFET (C-UMOSFET) and an accumulation layer UMOSFET (AL-UMOSFET) structures. For the NPC-UMOSFET with 10 µm drift region length the maximum breakdown voltage of 1274 V is obtained, while at the same drift region length, the maximum breakdown voltages of the C-UMOSFET and the AL-UMOSFET structures are 534 and 703 V, respectively. Moreover, the proposed structure exhibits a superior specific on-resistance (R_on,sp) of 2 mΩ cm², which shows that the on-resistance of the optimized NPC-UMOSFET are decreased by 56% and 58% in comparison with the C-UMOSFET and the AL-UMOSFET, respectively.     

A probabilistic load shedding concept considering highly volatile local generation

Automatic load shedding is the ultimate countermeasure against imbalance in a power system and can effectively help preventing large blackouts. Taking into account a high penetration of renewable energy sources (RES) in the distribution grid, a clear distinction between load and generation at the PCC becomes increasingly more difficult. For that reason an adaptation of frequency relay parameters and their locations of installation are necessary. In Europe this is rest on a multi-step plan based on values such as the yearly peak load. In this paper a novel probabilistic method for automatic load shedding is presented that uses the average values instead of peak values for load shedding. Its applicability is verified by a dynamic power system model that was developed to compare the classical and novel probabilistic load shedding principle. The method is verified using data from a German TSO.     

An interpretative structural modeling based network reconfiguration strategy for power systems

The network reconfiguration is an important stage of restoring a power system after a complete blackout or a local outage. Reasonable planning of the network reconfiguration procedure is essential for rapidly restoring the power system concerned. An approach for evaluating the importance of a line is first proposed based on the line contraction concept. Then, the interpretative structural modeling (ISM) is employed to analyze the relationship among the factors having impacts on the network reconfiguration. The security and speediness of restoring generating units are considered with priority, and a method is next proposed to select the generating unit to be restored by maximizing the restoration benefit with both the generation capacity of the restored generating unit and the importance of the line in the restoration path considered. Both the start-up sequence of generating units and the related restoration paths are optimized together in the proposed method, and in this way the shortcomings of separately solving these two issues in the existing methods are avoided. Finally, the New England 10-unit 39-bus power system and the Guangdong power system in South China are employed to demonstrate the basic features of the proposed method.