Effect of cationic surfactant and inorganic anions on the electrochemical behavior of carbon steel in formation water

Corrosion behavior of carbon steel in formation water associated crude oil from Egyptian western desert was studied at various concentrations of dodecyl dimethyl ammonium chloride (CS) as a cationic surfactant. Polarization curves indicate that CS has a good inhibition efficiency for carbon steel in formation water and behaves as cathodic inhibitor. The inhibition efficiency was found to increase with increase in CS concentration until reaches a maximum constant value corresponding to the critical micelle concentration of CS and decrease with increase in solution temperature. The adsorption of CS follows the kinetic thermodynamic model and Flory-Huggins isotherm. Thermodynamic parameters obtained indicate that that the presence of the CS increases the activation energy. Polarization and Impedance measurements indicate that the addition of KI has a significant synergistic effect with CS and results in increase the inhibition efficiency of CS in formation water.     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

The radiation crosslinking and scission of ethylene-propylene copolymers studied by solid-state nuclear magnetic resonance

Methyl groups from chain scission and H-crosslinks have been identified by solid-state nuclear magnetic resonance in amorphous ethylene-propylene copolymers containing 23 and 36 mole % propylene after γ-irradiation to 10 MGy at 30°C. G (scission) and G (crosslink) values determined from the n.m.r. spectra and by extraction are in agreement, which suggests that the crosslinks are not clustered. This may differ from the situation in polyethylene where there is a substantial crystalline content. G(S). G(X) and the ratio G(S)/G(X) increase with increasing propylene content of the copolymers.     

《C语言程序设计》课堂教学方法的探讨

《C语言程序设计》一直是计算机专业及相关专业的专业基础课。该课程既难教又难学。传统的教学方法往往过分注重语法形式的介绍，却忽视了算法的讲解，使得学生无法解决一些实际编程，也很容易挫伤学生的学习兴趣。为此应以算法教学为主。因材施教，合理使用教材，在改用多媒体教学的同时，适当配以板书。调动学生的主观能动性，提高其编程能力。     

Stable Oxygen and Carbon Isotopic Compositions of Lates stappersii Otoliths from Lake Tanganyika,East Africa

In this study, we measured growth trends in oxygen and carbon isotopic ratios in whole sagittal otoliths from three adult centropomid fish (Lates stappersii) from each of three sub-basins of Lake Tanganyika, East Africa. Sampling density was 20 to 50 samples per otolith. Both δ¹⁸O and δ¹³C values increase with age. The δ¹⁸O data suggest that otoliths were precipitated near the expected equilibrium with the ambient environment (ca. +3.5‰) and support a migration pattern from surface waters during larval stages to deeper waters (40 to 80 m) for mature fish. Relatively high δ¹⁸O values in the southern sub-basin are consistent with cooler temperatures in the region during seasonal upwelling. The δ13C increase from otolith core to edge is large (up to 4‰) and is interpreted as due to ontogenetic changes in diet and contributions from a decrease in the proportion of respired CO₂ incorporated into otolith carbonate as metabolic rates of the fish dropped with maturity. The data seem to successfully reveal life strategy and migration patterns of L. stappersii, document regional differences in lake conditions, and provide a record of temperature within the water column during which the fish lived. Higher resolution studies and analyses of historical samples could be used to constrain modern and past growth patterns, and to reconstruct past temperature gradients and productivity patterns in the lake.     

The development of a stress analysis code for nuclear graphite components in gas-cooled reactors

Most of the UK nuclear power reactors are gas-cooled and graphite moderated. As well as acting as a moderator the graphite also acts as a structural component providing channels for the coolant gas and control rods. For this reason the structural integrity assessments of nuclear graphite components is an essential element of reactor design. In order to perform graphite component stress analysis, the definition of the constitutive equation relating stress and strain for irradiated graphite is required. Apart from the usual elastic and thermal strains, irradiated graphite components are subject to additional strains due to fast neutron irradiation and radiolytic oxidation. In this paper a material model for nuclear graphite is presented along with an example of a stress analysis of a nuclear graphite moderator brick subject to both fast neutron irradiation and radiolytic oxidation.     

Oxygen glow discharge experiment to remove deposited layers and to release trapped hydrogen isotopes in HT-7 superconducting tokamak

An experiment to remove re-deposited layers and to release hydrogen using a glow discharge in oxygen (O-GDC) has been performed in the HT-7 superconducting tokamak. In the absence of magnetic fields, the O-GDC wall conditioning had produced rapid, controlled co-deposit removal. Average removal rates, 5.2 × 10²² H-atoms/h, 5.65 × 10²¹ D-atoms/h and 5.53 × 10²² C-atoms/h, respectively, were obtained during 145 min O-GDC experiment in the pressure range 0.5-1.5 Pa. The corresponding removal rate of co-deposited films was ∼1.19 μm/day (26.5 g/day for carbon) based on an area of 12 m². Compared to thermo-oxidation and O-ICR experiment, high pressure O-GDC wall conditioning promoted the oxidation and improved the C and D atoms removal. In the O-GDC experiment, the removal rates of H-atoms and D-atoms as H₂O, HDO and D₂O were higher than that of H₂ and D₂ by factors of about 20 and 50, respectively. During the 145 min O-GDC experiment, about 14.5% O-atoms were converted into carbon oxides and hydroxides, and about 5.37 × 10²² O-atoms were adsorbed on the walls corresponding to a coverage of 4.5 × 10²¹ O/m² on an wall area of 12 m². In a 100 min helium glow discharge (He-GDC) following the O-GDC experiment, 1.53 × 10²² O-atoms, about 28.5% oxygen retained on the walls, were removed. The removal rate of H-atoms in He-GDC cleaning after O-GDC experiment was lower than that in He-GDC cleaning before O-GDC experiment, which indicates that the O-GDC wall conditioning had effectively reduced hydrogen retention on the walls.     

Pressure infiltration of boron nitride preforms with molten aluminum

The infiltration of compacted cubic BN (cBN) with molten aluminum has been investigated as a potential route for a cheap and easy method of manufacturing cBN/metal composites. CBN compacts have been infiltrated with molten Al at a temperature between 670 and 800 °C and pressure of 15 MPa in vacuum. At these temperatures no pronounced interactions between hexagonal and cubic BN with Al was observed, allowing the complete infiltration of cBN with 12 μm mean grain size. After infiltration at 800 °C, the temperature was increased without pressure to convert aluminum into borides and AlN. The hardness of the resulting materials depends on the content of hexagonal, cubic BN and the rate of conversion of Al into borides and AlN. The infiltration height of less than 1 mm obtained from infiltrating the 3 μm cBN powder green compacts gave a hardness of 22.0 ± 0.6 GPa after heat treatment.     

La doping effects on intergrowth Bi2WO6–Bi3TiNbO9 ferroelectrics

La doping effects on intergrowth Bi₂WO₆–Bi₃TiNbO₉ ferroelectric ceramics were studied by X-ray diffraction, electron probe microanalysis and dielectric spectroscopy. It was found that the La³⁺ distribution, ferroelectric phase transition and dielectric relaxation behavior are apparently affected by La doping. With increasing La³⁺ content, the site of dopant ion varies, the grain growth of Bi₅TiNbWO₁₅ is restrained, the Curie temperature is reduced and broadened. Furthermore, two dielectric relaxation loss peaks were observed both in temperature and frequency spectra. The calculated relaxation parameters revealed the oxygen vacancy related to the relaxation process.     

钢样成分化验分析结果网络传输系统的开发与应用

钢样成分化验分析结果网络传输系统将碳硫分析仪、光谱分析仪和相应的计算机控制系统按以太网络结构组联,形成"炉前分析网络",采用分析网主服务器系统软件和网络分析系统软件实现网络传输。该系统可将炉前钢样化验分析结果实时传输到炉前大屏,具有传输速度快、准确率高的特点,提高了工作效率和产品合格率,降低了生产成本。