HZSM5分子筛膜复合二氧化锡对甲烷的气敏性能研究

采用液相氧化法制备二氧化锡纳米颗粒,并利用浸渍法制备Pd负载二氧化锡纳米材料,通过丝网印刷得到气敏传感膜并在其表面印刷分子筛层。基于动态气敏测试系统探究传感器对甲烷气体的灵敏度及其在CO和乙醇干扰气体下的选择性。研究结果表明,在Pd-SnO₂敏感层表面印刷Pd-HZSM5层后,传感器对甲烷的响应能力显著提高,并且在体积分数为5×10^-4的CO存在时,对甲烷的选择性也得到明显的提升。同样,在质量分数为2×10^-5乙醇的存在下,传感器对甲烷的响应也没有受到干扰。通过对分子筛进行表征和催化分析,发现Pd-HZSM5对CO的催化效率可达100%,使得CO在扩散过程中被催化氧化,这可能是印刷Pd-HZSM5分子筛膜从而提高传感器选择性的主要原因。同时研究还表明,在敏感层表面印刷分子筛层并不会影响传感器的响应和恢复速率。     

等速升温流态化下CaO/生物质焦的SO2/NO联合脱除特性

燃煤锅炉污染物超低排放标准对电厂脱硫和脱硝系统提出了更高的要求。CaO作为脱硫剂可以实现循环流化床锅炉烟气中SO₂的高效脱除,焦炭作为还原剂直接还原NO,同时CaO的存在对焦炭还原NO起催化作用,可以实现燃煤烟气中SO₂/NO的联合脱除。为了探究连续温度变化对CaO/生物质焦联合脱硫脱硝性能的影响,在钙循环捕集CO₂技术背景下,研究了等速升温流态化下CaO/生物质焦的SO₂/NO联合脱除特性。探究了烟气中O₂和CO₂对CaO/椰壳焦脱除SO₂/NO的影响。结果表明,O₂通过对椰壳焦表面碳原子的活化作用降低了异相还原NO温度,在300~950℃等速升温过程中CaO/椰壳焦的NO脱除效率逐渐增加,780℃以上能实现100%脱硝。O₂也提高了CaO/椰壳焦的脱硫效率。CO₂与CaO的碳酸化反应以及与椰壳焦的气化反应对同时脱除SO₂/NO有明显抑制作用。O₂和CO₂共同作用下,在500~800℃内CaO/椰壳焦的脱硝效率随温度升高而增加,脱硫效率先降低后升高。NO促进了CaO/椰壳焦脱除SO₂,而SO₂对脱硝有抑制作用。800℃时CaO/椰壳焦同时脱除SO₂和NO的效率分别为97.7%和93.9%。     

H2O(g)对富氧燃烧超细颗粒物生成特性影响

为实现富氧燃烧技术的广泛推广,对煤粉燃烧在富氧气氛下的颗粒物排放特性进行了研究。在1800 K管式炉内进行煤焦燃烧试验,研究了富氧气氛下H₂O(g)体积分数(0、5%、10%、20%、30%)对煤焦燃烧超细颗粒物的影响;采用荷电低压撞击器(ELPI+)获得超细颗粒物质量和数量浓度粒径分布并进行分析。结果表明,H₂O(g)对超细颗粒物质量浓度和数量浓度粒径分布无影响,但会导致超细颗粒物的峰值波动。超细颗粒物总数量由最小粒径超细颗粒物决定,5种水蒸气浓度下EL?PI+第1级撞击器收集到的超细颗粒物数量占比均超过65%。超细颗粒物总质量由最大粒径超细颗粒物决定,5个水蒸气浓度下ELPI+第7级撞击器收集到的超细颗粒物质量占比均超过94%。低H₂O(g)浓度会抑制超细颗粒物生成,H₂O(g)体积分数为5%时的抑制作用最显著;高H₂O(g)浓度会促进超细颗粒物生成。这是因为一方面H₂O(g)与煤焦发生气化反应,使煤焦颗粒周围产生还原性气氛,促进矿物质还原为单质,进一步促进矿物质蒸发;另一方面气化反应是吸热反应,会降低煤焦颗粒燃烧温度,同时H₂O(g)加入也导致烟气热容增加进一步降低,煤焦燃烧温度抑制煤中矿物质的蒸发,导致超细颗粒物生成减少,是2种作用相互竞争的结果。此外,H₂O(g)的加入使超细颗粒物平均粒径增大,0~5%H₂O(g)时超细颗粒物平均粒径增大最迅速。     

25Cr2Ni4MoV钢转子轴颈损伤修复工艺研究

汽轮发电机运行过程中,转子轴颈磨损拉伤的情况较为普遍,采用微弧冷焊技术可以实现对损伤部位的修复。针对25Cr2Ni4MoV材料转子,通过焊接工艺试验和试样性能检测,得到一种可靠的微弧冷焊工艺;并通过对焊缝无损检测标准和焊后尺寸恢复工艺的研究,形成了一套完善的轴颈损伤修复工艺方案。     

基于MMS替代协议的变电站安全通信技术研究及应用

目前,绝大多数变电站基于IEC61850标准建设,站内通信协议主要包括制造报文规范(MMS)、面向通用对象的变电站事件(GOOSE)、采样测量值(SMV)等,在工程应用实践中逐渐暴露出一些不足与安全隐患.为此,基于MMS替代协议,重点介绍了其实现的功能与安全防护技术.在功能方面,MMS替代协议增加了多个服务,并优化了现有MMS协议的不足;在安全防护技术方面,MMS替代协议的应用层实现了基于SM2算法与调度证书的双向身份认证,杜绝未授权设备的非法接入、攻击,从协议源头杜绝设备连接的不安全性;MMS替代协议的传输层实现了基于SM2算法与调度证书的全链路加密、认证,确保传输数据报文防伪造、防抵赖、防窃取,保护数据报文的机密性、完整性.测试结果表明MMS替代协议在工程应用中具有一定的参考意义.     

Influence of pre-oxidation on the hot corrosion of Ti3SiC2 in the mixture of Na2SO4-NaCl melts

Polycrystalline Ti₃SiC₂ suffered from serious hot corrosion attack in the mixture of 75wt.%Na₂SO₄ + 25wt.%NaCl melts at 850 °C. In order to improve the hot corrosion resistance of this material, pre-oxidation treatment was conducted at 1200 °C in air for 2 h. A duplex oxide scale with an outer layer of TiO₂ and an inner layer of a mixture of TiO₂ and SiO₂ was formed during the pre-oxidation. Because the outer oxide layer of the pre-oxidation treated specimens could inhibit hot corrosion process, they exhibited good hot corrosion resistance in the mixture of 75wt.%Na₂SO₄ + 25wt.%NaCl melts at 850 °C for 50 h. However, during the hot corrosion the outer layer of TiO₂ would degrade gradually. Once the outer layer damaged, the hot corrosion rate increased sharply, the corrosion behavior was similar to Ti₃SiC₂ corroded under the same conditions. The microstructure and phase compositions of the hot corrosion samples were investigated by SEM/EDS and XRD.     

La3+ 掺杂对 CeO2 红外发射性能的影响研究

随着飞行器飞行速度和发动机燃烧室温度的提高, 金属类隐身涂层材料已无法满足环境使用要求。 CeO2 具有较高熔点、 抗氧化、 较低红外发射率等特点, 被认为是红外隐身应用的候选材料, 但其发射率仍无法满足 高温红外隐身需求。 本文通过固相反应法对 CeO2 进行 La3+ 掺杂改性, 研究掺杂量对 CeO2 粉体红外发射性能的 影响规律。 结果表明, 随着掺杂量从 10 mol% 增加到 30 mol%, 粉体在 3~6 μm 波段的发射率不断降低, 其中 Ce0.7La0.3O2 的红外发射率仅为 0.1。     

TEM and DFT investigation of CVD TiN/κ-Al2O3 multilayer coatings

This paper investigates the interfacial structure in hot-wall CVD TiN/κ-Al₂O₃ multilayer coatings using both HREM and DFT modeling. Two multilayers with different thicknesses of the TiN layers (50 and 600 nm) separating the κ-Al₂O₃ layers are analyzed. The general microstructure of the two multilayers is relatively similar. The TiN layer in the thicker TiN/κ-Al₂O₃ coating is thick enough to be several TiN grains high. This means that epitaxial columns, which are often found in the thinner TiN/κ-Al₂O₃ coatings, are not present. However, the orientation relationships at the TiN/κ-Al₂O₃ interfaces are the same in both multilayers. The HREM investigations show that κ-Al₂O₃ (001) planes can grow directly on flat (111) TiN faces, without any other phases or detectable amounts of impurities, such as sulphur, present. Where the TiN layers are more curved, γ-Al₂O₃ can be grown, at least partly stabilized by the cube-on-cube orientation relationship between γ-Al₂O₃ and the underlying TiN. The DFT calculations show very similar adsorption strengths for an O monolayer positioned on Ti-terminated TiC(111) and TiN(111) surfaces, with preferred adsorption in the fcc site. O adsorption on N-terminated TiN(111) is much weaker, with preferred adsorption in the top site. Calculated elastic-energy contributions yield a higher stability for κ-Al₂O₃ on TiN(111) than on TiC(111) and a higher stability for κ-Al₂O₃ than for α-Al₂O₃ on both TiC and TiN. This indicates that the observed higher stability of κ-Al₂O₃ on TiC(111) than on TiN(111) is not due to the lattice mismatch, while the preferred epitaxial growth of κ-Al₂O₃ over α-Al₂O₃ can be partly attributed to the mismatch.     

挤压机机电控制系统研究

本文探讨了12．5MN轻合金挤压机的机电系统控制问题，对应用电液比例技术，伺服控制技术、模／数、数／模转换器及可编程控制器实现等温挤压的具体方法作了深入细致的研究，文中论述方法对挤压机的机电系统控制具有一定的普遍意义。     

变频器干扰产生的原因及防范措施

介绍了电动设备中使用的变频器产生干扰的原因、传播途径，及相应的抗干扰措施，提出了在变频器系统设计和安装过程中应注意的问题。