汽车排放控制系统中的氧传感器现状及展望

介绍了浓差型(Nernst型)、极限电流型和半导体电阻型等汽车排放控制系统中的氧传感器原理及结构。在综合该领域国内外研究现状的基础上,对氧传感器的发展进行了展望。     

14 kV single-phase superconducting fault current limiter based on YBCO films

We present the fabrication and short circuit test results of a 14 kV single-phase resistive superconducting fault current limiter (SFCL) based on YBa₂Cu₃O₇ (YBCO) films. Individual components were processed using the 4″ YBCO films and have the rated voltage and current of 600 V and 35 A at 77 K, respectively. Twenty four components, eight components in series and three lines in parallel, make a module having the rated voltage and current of 4.8 kV and 105 A, respectively. Three modules were assembled in series to produce the SFCL working at 77 K, a 14 kV single-phase machine for the 22.9 kV Y-Y grid. short circuit tests were successfully conducted in an accredited test facility with the maximum fault currents up to 14.1 kA_P. All components quenched together upon faults and shared the rated voltage evenly without any supplementary device between the modules. This proves that the SFCL based on YBCO films may not only work reliably at 22.9 kV, but also provide technical feasibility for higher voltage application including the transmission grids.     

企业材料耗用的统计分析与评价

本文利用回归分析导出材料耗用的回归方程 ,并对方程进行拟合优度检测和显著性检验 ,以及对材料耗用情况进行综合评价。     

A complete VARMA modelling methodology based on scalar components

Abstract. This article proposes an extension to scalar component methodology for the identification and estimation of VARMA models. The complete methodology determines the exact positions of all free parameters in any VARMA model with a predetermined embedded scalar component structure. This leads to an exactly identified system of equations that is estimated using full information maximum likelihood.     

F2.4微孔膜的制备及在膜蒸馏过程中应用的初步研究

采用相转化法制备了F2 4的疏水微孔膜 ,并对F2 4和PVDF微孔膜的机械性能以及疏水性等方面进行了对比 .结果表明 ,F2 4微孔膜在拉伸时的应变以及断裂伸长率约为PVDF微孔膜的 6～ 9倍 ;其接触角 (77 4°)也大于PVDF膜的接触角 (6 6 7°) .尽管膜蒸馏的数据显示F2 4微孔膜的蒸馏通量尚不及PVDF膜 ,但通过调节各项制膜参数 ,F2 4可能具有良好的应用前景     

节能建筑中人体传热模型和计算公式

讨论人体新陈代谢发热率及其影响因素;论述节能建筑中舒适的环境温度、空气相对湿度、空气流速以及新鲜空气供给量的最佳值范围;同时考虑皮肤和肺部的显热散热和蒸发潜热散热,建立了传热模型,得出了计算公式。     

4F0.06AC树脂吹塑薄膜技术的探讨

在加工应用试验的基础上。探讨了加工温度、吹胀比、超想线高度及设备对４Ｆ０．０６ＡＣ薄膜适宜的加工条件。     

Design of a high-pressure ebulliometer,with vapor-liquid equilibrium results for the systems CHF2 Cl + CF3 CH3 and CF3 CH2 F + CH2F2

We describe the design and operation of a new high-pressure metal ebulliometer which can operate at pressures to at least 3 MPa in the range 220–400 K. Infinite-dilution activity coefficients are presented for the system CHF₂Cl + CF₃-CH, at 275 K and for the system CF₃-CH₂F + CH₂F₂, at 260, 230, and 300 K. The Wilson activity coellicient model and a virial coefficient model are applied to these systems, and the phase equilibrium conditions are calculated. The results are shown to agree well with predicted and with published measured values. The excess enthalpy is calculated and compared with results from a Peng Robinson equation of state. Vapor densities on the dew curves are given.     

工业固体核磁Magmonitor用于聚烯烃质量参数测试方法的建立

利用实际采集的系列试样 ,在工业固体核磁Magmonitor(IMR)上建立了标准曲线 ;在IMR上运行标样的核磁信号后 ,对FID信号与实验数值之间的匹配使用 32个误差分析因子进行分析 ,并在Cregcon软件下运行回归分析 ,将结果转化成仪器预测模型。结果表明 ,测试相对偏差在 10 %以内 ,数据重现性好 ,而粉料与共聚物的测试误差有待改进。将IMR测试结果与不同测试方法进行比较 ,建议测试前对粉料进行脱气与脱水处理     

汽车组合仪表板控制系统设计

介绍了以PIC16F873单片机为控制核心的汽车组合仪表板控制系统的设计,简述了汽车组合仪表板的基本构成,介绍了汽车组合仪表板控制系统的组成和各部分功能,给出了数据采集处理电路、电源电路等部分硬件电路设计方案,并阐述了一些软件设计算法,如分段插补法和用于平滑指针的软件设计算法等。