伶仃洋三维潮流输沙的数值模拟

作者使用垂向坐标变换技术，结合有限差分方法建立了三维潮流输沙的数学模型。为了增加模型的稳定性和减少数值耗散，对悬沙对流扩散方程中的水平对流项采用三阶迎风格式离散。应用本模型对伶仃洋的枯季和洪季的潮流输沙的悬沙场进行了数值模拟，将模拟结果与实测资料进行比较，二者吻合较好。模拟结果分析表明：伶仃洋悬沙运动主要集中在西滩，对伶仃航道影响不大；洪季水体含沙浓度高于枯季；水体含沙浓度沿水深存在浓度梯度，且洪季的浓度梯度明显大于枯季。     

带通采样在数据采集中的应用研究

在数据采集中采用带通采样，可大大降低采样率，但系统中的抗混叠滤波器会造成相位的非线性。采用对滤波后的信号进行带通采样，然后再用FRR滤波器校正相位的非线性，从而不失真地还原原信号，最后在Matlab中进行仿真，验证了该方法的有效性。     

用增量的累积量方法测量大气风场

为了在非平稳、非线性条件下能得到真实风场的良好估计,提出了一种用空间分布天线（SA）雷达信号的增量累积量测量大气风场参数的方法。该方法基于结构函数方法,利用高阶累计量在信息处理中的特性,用零延迟的增量累计量求解平均水平风速等具体参量，并在大气散射模型基础上对增量累积量方法进行了数值模拟,得出了同理论分析一致的结果.分析和计算表明,该方法完全适用于局地平稳条件，可以减小风场参量估计对天线间距的敏感度；阶数k≥3时,对高斯噪声有很强抑制;同时可以得到风场参量的高阶估计，这是普通的二阶方法（如全相关分析、全谱分析）不具备的。     

Hopping and optical absorption of electrons in nano-porous crystal 12CaO·7Al2O3

Recently it has been discovered that a nano-porous main group oxide 12CaO·7Al₂O₃ (C12A7) can be converted from a wide-gap insulator to a good transparent conductor. Using ab initio modelling we explain good conductivity of this material by very small barriers for hopping of localised electrons between neighbouring positive cages. We show that optical absorption of C12A7 in infrared region and at energies higher than 2.7 eV is due to inter-cage and intra-cage electron transitions, respectively. The proposed mechanisms can be useful in further search for conducting transparent media.     

L－B膜修饰电极循环伏安行为模拟──（Ⅰ）电荷转移速度常数对循环伏安性能的影响

本文用计算机数字模拟方法研究了电活性分子多层Ｚ型Ｌ－Ｂ膜修饰电极的循环伏安行为。计算了电极与修饰Ｌ－Ｂ膜分子第一层之间的电荷转移速度常数Ｋ_ｏ，Ｌ－Ｂ膜分子层间的电荷转移速度常数ｋ_ｉ；对峰电位差△Ｅ_ｐ及阳极峰面积Ｑ的影响，以及在不同条件下各层分子的氧化态分数随扫描时间的变化。为研究和设计电活性分子修饰电极的实际体系提供了大量数据和信息。     

单片机仿真系统

本文讨论单片机离线仿真系统的设计方法，其关键技术是：单片机硬件系统（ＲＡＭＲＥＧＩＳＴＥＲＳ）仿真，指令系统仿真，中断系统仿真，应用系统硬件仿真。     

利用反射纵波评价裂缝倾角的模拟实验研究

声波全波列测井中的反射纵波可以用来评价高角度裂缝和对井周附近地质结构进行成像。目前的研究主要侧重于直接从波形资料处理出发计算裂缝的位置和倾角 ,其可靠性和准确性无从评价和校验。文中采用模拟实验的方法记录了倾角为 6 0°～80°范围内的 8种倾角裂缝的反射脉冲纵波波形 ,自行推导了反演裂缝倾角的公式 ,结合波场分离技术对实验测量波形数据进行了处理 ,计算出的裂缝倾角与实际值具有良好的一致性。本文结果表明 ,利用至少 2个深度点的纵波反射波波形资料就可以准确地反演裂缝的倾角     

CD++: a toolkit to develop DEVS models

The features of a toolkit for modeling and simulation based on the DEVS formalism are presented. The tool is built as a set of independent software pieces running on different platforms. Not only are the main characteristics of the environment presented, a focus on its use is also considered by inclusion of application examples for a variety of problems. Many models can be defined in an automated fashion, simplifying the construction of new models and easing their verification. The use of this formal approach has allowed the development of safe and cost‐effective simulations, significantly reducing development time. Copyright © 2002 John Wiley & Sons, Ltd.     

Influence of the intrinsic layer characteristics on a-Si:H p–i–n solar cell performance analysed by means of a computer simulation

In this paper a set of one-dimensional simulations of a-Si:H p–i–n junctions under different illumination conditions and with different intrinsic layer are presented. The simulation program ASCA permits the analysis of the internal electrical behaviour of the cell allowing a comparison among the different internal configurations determined by a change in the input set. Results about the internal electric configuration will be presented and discussed outlining their influence on the current tension characteristic curve. Considerations about the drift–diffusion and the generation–recombination balance distributions, outlined by the simulation, can be used to explain the correlation between the basic device output, the i-layer characteristics (thickness and DOS), the incident radiation intensity and photon energy.