镀镍云母导电复合材料的研究

对云母粒子化学镀镍及以LDPE为基材,镀镍云母粒子为填料制备的导电复合材料进行研究。认为此种导电复合材料只有质量轻、强度大及良好的导电等性能。     

一种蒸发式冷凝器的新型设计方法

蒸发式冷凝器设计方法的粗糙和繁琐限制其广泛应用,特别是限制其应用于民用和小型商用建筑中。针对上述问题,作者通过实验研究了蒸发式冷凝器的影响因素（进风湿球温度、最小截面风速和喷淋水量）对蒸发式冷凝器热质交换的影响。同时提出了一种新型设计方法,此方法简单,精度较高。适合工程设计、选型和生产应用。     

Direct electroless Ni-P deposition on AM50 magnesium alloy from sulfate bath

A bright electroless Ni-P deposition on AM50 magnesium alloy in a sulfate plating bath was proposed by using direct plating process with non-chromate pretreatment. The electroless Ni-P plating on AM50 magnesium alloy has an admirable appearance and good adhesion. The results indicate that the electroless Ni-P deposition with non-chromate pretreatment has better adhesion than that of zinc immersion coating. Anodic polarization curves indicate that the electroless Ni-P deposition obtained from the sulfate bath has similar corrosion-resistance to that obtained from basic nickel carbonate bath. The deposition process generates less pollutant by a non-chromate plating bath and is suitable for the magnesium alloys manufacture because of its low cost. The hardness of the electroless Ni-P plated AM50 is about HV 720.6 and HV 969.7 after heat treatments at 180℃ for 2 h. The wear resistance of Ni-P plated magnesium alloy specimens is about 5 to 9 times as high as that of bare magnesium alloys.     

NiCuZn铁氧体和银内电极的共烧行为

NiCuZn铁氧体正作为磁介质广泛地应用于低烧多层片式电感，因此有必要对其与银内电极的共烧行为进行研究。该文主要介绍NiCuZn铁氧体／银内电极多层复合体共烧过程中的烧结收缩、界面反应、扩散对介质性能的影响。尖晶石结构中存在相当数量的空位，这为银离子提供了一定的溶解度，因此在共烧过程中银对铁氧体的相组成影响较小。银对铁氧体性能的影响体现在两个方面。一方面是由于银具有相对低的烧结温度，从而在烧结过程中起到助烧剂的作用，促进致密化过程，提高烧结体的密度和磁导率；另一方面，银促使铁氧体中的铜在晶界处析出，导致晶界处应力，使磁导率降低，晶粒生长也被一定程度地抑制。     

高功率双工旋转场移相器

旋转场移相器具有移相精度高(均方根误差可小于1°)和温度稳定性好等特点,通过改进射频传输结构,可大大提高他的功率容量。利用旋转场移相器的互易特性和铁氧体圆极化器的非互易特性,设计出高功率双工旋转场移相器。其双工特性可将收/发信号分开,实现移相器和环行器的双重功能,用于天线的收发通道等场合时,可省去一个高功率环行器,结构紧凑。分析了双工旋转场移相器的工作原理,阐述了高功率应用下的设计方法,推导出了管状铁氧体的相移量计算公式,按此方法设计了实用的器件,并给出了试验数据。     

Effect of Additives on Magnetic Properties of High Frequency MnZn Power Ferrite

In keeping with the advance of more compact and more power-saving electronic equipment, the demand is increasing for smaller and more efficient switching power supply. Therefore, it is necessary to provide the adequate magnetic power ferrite materials to satisfy the demand. Such ferrite materials have to meet the following main requirement: 1) high initial permeability (μ i ); 2) high saturation magnetic induction (Bs); 3) high Curie temperature (Tc); 4) high electrical resistivity (ρ ); 5)…     

化学镀工艺在微电子材料中的研究和应用

简要综述了化学镀工艺在微电子材料中的应用,讨论了影响化学镀镍、铜、锡、钴和贵金属等的主要因素,阐述了化学镀微电子材料的特性、存在问题及研究动态。     

THE REACTIVITY AND DURABILITY OF ZINC FERRITE HIGH TEMPERATURE DESULFURIZATION SORBENTS

Cylindrical pellets of zinc ferrite high temperature desulfurization sorbent have been prepared using a number of formulation recipes and induration conditions. Physical and structural properties of the resultant sorbents were measured, and reactivity and durability screening tests were carried out using a single pellet electrobalance reactor. The formulation variables studied were ZnO to Fe₂O₃ ratio, Fe₂O₃ source, and the addition of inorganic (bentonite) and organic (methocel) binders to the sorbents. Pellet induration conditions ranged from 0.25 hours at 815^°C to 4.0 hours at 1038°C. Stronger pellets having greater attrition resistance resulted when 5% bentonite was added to the formulation recipe and when the pellets were indurated at high temperature for extended times. In contrast, bentonite content was not a significant factor in determining sorbent reactivity and durability, both of which were improved by mild induration conditions. Sorbent regeneration temperature was found to be an important factor in improving reaction durability, as was the addition of 0.5% methocel to the formulation recipe. Pellets containing catalyst-grade Fe₂O₃ were more reactive than those containing pigment-grade Fe₂O₃. This effect, however, was less important than the effect of induration conditions.     

Effect of Reactor Ambient Pressure on the Morphology of Spray Dried Magnesium Sulphate Powders

The effect of reducing the reactor air pressure on the morphology of spray dried magnesium sulphate powders is investigated, experimentally. A reactor, capable of drying and pyrolyzing solution sprays at low pressures, is designed and manufactured. A vibrating mesh nebulizer is employed to generate the spray. Four different pressures, starting from 60 Torr to the atmospheric pressure, and two different reactor air temperatures of 130°C and 420°C, are considered. In addition, two different concentrations of magnesium sulphate solutions are tested. The results are explained based on the effect of reactor air pressure on the droplet evaporation rate.     

Studies on spray pyrolyzed molybdenum trioxide thin films

Semiconducting molybdenum trioxide thin films have been prepared by employing simple and inexpensive spray pyrolysis technique. Films are found to be polycrystalline in nature with hexagonal phase. Optical band gap energy (direct) and room temperature electrical resistivity are of the order of 2·9 eV and 10⁸ ohm-cm, respectively. These films exhibit cathodic electrochromism.