英台地区天然水驱油藏的开发特点及稳产技术

掌握边底水运动规律，控制并利用活跃的边底水能量，是成功开发天然水驱油藏的关键。英台地区的英台、四方坨子和一棵树等三个油田均为天然水驱油藏，天然能量充足。油藏投入开发后初期含水较高，含水上升极快，造成产油量大幅度递减。针对其开发特点，适时采用大泵、电潜泵提液强采，通过大量补孔层间接替以及加密调整和扩边等稳产技术措施，确保了油藏以3％-5％的采油速度长期稳产，水驱采收率高达50％以上。     

Optimum thermoeconomic and thermodynamic performance characteristics of an irreversible three-heat-source heat pump

The coefficient of performance and specific heating load of an irreversible three-heat-source heat pump are given by using a general cycle model affected by the finite-rate heat transfer, heat leak and internal irreversibility of the cyclic working fluid. The heat pumping load divided by the total cost per unit time is taken as a new objective function and used to investigate the performance of the heat pump. The thermoeconomic and thermodynamic performance characteristics of the heat pump are discussed in detail. Some important performance parameters such as the thermoeconomic objective function and coefficient of performance are optimized. The optimally operating regions of the heat pump and the bounds of several performance parameters are determined. Finally, it is pointed out that the Carnot heat pump may be taken as a special case of a three-heat-source heat pump and consequently its optimal performance can be directly derived from the results obtained here.     

第三代伞状喷雾的分布特性及多片喷雾系统的应用研究

为解决前两代伞状喷雾在高背压下贯穿距不足的问题,借鉴碰撞喷雾方式,提出了第三代伞状喷雾概念。通过高速摄影对喷雾的分布特性进行了研究,结果表明:喷雾具有贯穿距可设定、扩散度高、空间分布均匀等特点。为避免碰撞后二次油束雾线相互干涉,又提出了一种多片喷雾概念,并在单缸四气门135柴油机上对多片喷雾燃烧系统进行了初步的性能试验,结果显示:系统能够有效地促进缸内均质混合气的形成;在供油提前角为19°CA时,全负荷范围内柴油机的油耗和碳烟排放均较低。     

液氨装置工艺计算及改造总结

介绍我公司液氯装置由活塞式氨气压缩机氨-CaCl2盐水系统改为带经济器的螺杆式氯气液化机组的工艺计算,新建装置特点以及改造后的装置在我公司运行情况和使用效果。经改造后的液氯装置每年可节约电费73万余元,同时提高了装置的安全可靠性。     

中央空调冷冻水泵变频调速运行特性研究(2):模拟计算与分析

利用前文的分析结果，对采用定压差控制的某空调系统进行了模拟计算，并将计算结果与相似定律所得结果进行了比较，表明直接按相似定律所确定的泵的扬程和能耗均偏低；同时对冷冻水管路系统中的雷诺数Re、沿程阻力系数和管路阻抗等随空调负荷的变化关系，以及空调负荷分布、压差设定值等对冷冻水泵变频运行参数及能耗的影响等方面进行了分析，提出了冷冻水泵变频的最有利及最不利工况，并根据模拟与分析结果对空调冷冻水泵变频调速系统的设计等提出了建议。     

Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system in a diesel engine

This paper investigates the effect of injection parameters on the characteristics of dimethyl ether (DME) as an alternative fuel in a diesel engine with experimental and analytical models based on empirical equations. In order to study macroscopic and microscopic characteristics of DME fuel, this work focuses on the atomization characteristics of DME and compares experimental and predicted results for spray development obtained by empirical models for diesel and DME fuel. Detailed comparisons of spray tip penetration from three different empirical correlations and from visualization experiments of diesel and DME fuels were conducted under various fuel injection conditions. In comparison with the results of different empirical equations for measured spray tip penetration, the experimental results of this study provide good agreement with the calculation results based on empirical equations, except during the earliest stage of the injected spray sequence. The results of atomization characteristics indicate that DME showed better spray characteristics than conventional diesel fuel. Also, the fuel injection delay and maximum injection rate of DME fuel are shorter and lower than those of diesel fuel at the same injection conditions, respectively.     

双柱塞砂浆泵中工作机构的设计和仿真研究

本文介绍了双柱塞砂浆泵的工作原理，根据机构替代原理建立起双柱塞砂浆泵工作机构的运动分析模型，然后在MatLab环境下，详细介绍了工作凸轮曲线的设计程序，利用计算机设计程序可以方便地分析工作缸活塞以及工作凸轮机构的位移、速度、加速度，利用SIMULINK仿真工具箱进行运动学仿真，为工作机构设计提供相应的理论分析依据。     

离心压缩机可倾轴瓦油封漏油问题的解决

本文全面分析了DH80—16型离心压缩机可倾轴瓦油封漏油的原因,并介绍了可倾轴瓦油封漏油问题的解决及具体实施方案。     

海水泵房土石方开挖及大围堰施工回顾

着重说明海水泵房临海的大围堰工程是厂区土石方开挖和厂房施工的先决条件之一。外方设计方案偏离厂址实际情况 ,存在许多施工难题。中方根据厂区实际情况 ,提出新的施工方案 ,不仅保证了1 998年 6月 8日第一罐混凝土施工 ,还节约了几百万资金     

Fabrication and characterization of Cu2ZnSnS4 thin films deposited by spray pyrolysis technique

We have investigated synthesis conditions and some properties of sprayed Cu₂ZnSnS₄ (CZTS) thin films in order to determine the best preparation conditions for the realization of CZTS based photovoltaic solar cells. The thin films are made by means of spraying of aqueous solutions containing copper chloride, zinc chloride, tin chloride and thiourea on heated glass substrates at various temperatures. In order to optimize the synthesis conditions of the CZTS films, two series of experiments are performed. In the first series the sprayed duration was fixed at 30 min and in the second it is fixed at 60 min. In each series, the substrate temperature was changed from 553°K to 633°K. The X-ray diffraction shows, on one hand, that the best crystallinity was obtained for 613°K as substrate temperature and 60 min as sprayed duration. On the other hand, these CZTS films exhibit the kesterite structure with preferential orientation along the [112] direction. Atomical Force Microscopy was used to determine the grain sizes and the roughness of these CZTS thin film. After the annealing treatment, we estimated the optical band-gap energy of the CZTS thin film exhibiting the best crystallinity as 1.5 eV which is quite close to the optimum value for a solar cell.