Flammability characteristics at applied heat flux levels up to 200 kW/m2

This paper documents the first of the two interrelated studies that were conducted to more fundamentally understand the scalability of flame heat flux, the motivation being that it has been reported that flame heat flux back to the burning surface in bench‐scale experiments is not the same as for large‐scale fires. The key aspect was the use of real scale applied heat flux up to 200kW/m² which is well beyond that typically considered in contemporary testing. The main conclusions are that decomposition kinetics needs to be included in the study of ignition and the energy balance for steady burning is too simplistic to represent the physics occurring. An unexpected non‐linear trend is observed in the typical plotting methods currently used in fire protection engineering for ignition and mass loss flux data for several materials tested and this non‐linearity is a true material response. Using measured temperature profiles in the condensed phase shows that viewing ignition as an inert material process is inaccurate at predicting the surface temperature at higher heat fluxes. The steady burning temperature profiles appear to be invariant with applied heat flux. This possible inaccuracy was investigated by obtaining the heat of gasification via the ‘typical technique’ using the mass loss flux data and comparing it to the commonly considered ‘fundamental’ value obtained from differential scanning calorimetry measurements. This comparison suggests that the ‘typical technique’ energy balance is too simplified to represent the physics occurring for any range of applied heat flux. Observed bubbling and melting phenomena provide a possible direction of study. Copyright © 2007 John Wiley & Sons, Ltd.     

开放式玻璃自动切割机计算机控制系统

文章介绍一种自行研制的玻璃自动切割机开放式计算机控制系统，并针对该切割机加工范围大、惯性大、动态精度要求高等特点，研究了一种智能适应型PID控制算法。现场测试表明，该系统在功能、性能和控制精度上达到或接近国外同类产品的先进水平，在系统硬件和软件的开放性上优于国外产品。文中详细介绍了该计算机控制系统的功能、系统设计、控制算法及其调试结果。     

大小样品在液氮中的淬冷沸腾换热比较研究

分析了大小样品在液氮中的淬冷沸腾换热特性。大小样品的淬冷沸腾换热有着明显的差别，小样品的热流密度比大样品的明显高得多。小样品的淬冷沸腾有一起始段，其温降高达６０Ｋ。从实验结果还可以看到，小样品的Ｌｅｉｄｅｎｆｒｏｓｔ点和临界热流点对应的壁面过热度明显比大样品的高。最后还分析了样品直径对临界热流密度的影响。     

感应电动机转速对定子电流暂态过程的影响

本文运用根轨迹法，分析了感应电动机转速对定子电流暂态过程的影响。并通过对稳态时定子电流在电压阶跃干扰下的暂太响应分析，验证了结论有效性。     

Effect of site-selective substitution in bulk superconducting Tl2Ba2CaCu2O8

Magnetization measurements were carried out on bulk Tl₂Ba₂CaCu₂O₈ (referred to as Tl-2212) and on various site-selective substituted Tl-2212 samples. At 5K between 0 and 4.5 T, the 5 at. % Mg-doped Tl-2212 (Tl,Mg-2212) samples displayed enhanced pinning as demonstrated by a field dependent increase of the magnetic critical-current density J_c by 18 to 25 percent over that of pristine Tl-2212. Excess Mg (10–15 at. %), however, is deleterious. Rietveld refinement of the x-ray diffraction pattern showed Mg on the Tl sites. Auger electron spectroscopy analysis showed part of the Mg on grain boundaries. The flux-creep activation energies are higher for flux expulsion than for flux penetration in both Tl-2212 and Tl,Mg-2212 samples; the latter displays higher individual values. Our results demonstrate an increase in the number density of flux lines as a result of increased density of atomic-size-structural, defects by Mg (5 at. %) doping. In the Tl_2−yBa₂(Ca_1−zY_z)Cu₂O_8−x(z=0–0.3; single phase; x and y represent oxygen and thallium vacancies) system also studied, the T_c decreases as z increases. At z=0.3, the sample becomes an antiferromagnetic semiconductor.     

管杆漏磁探伤现场应用中的问题及对策

阐述了漏磁探伤漏磁场沿管、杆径向的分布特征 ,分析了影响探伤装置漏磁检测准确性的 4个因素 ,验证了信号提离距离的变化对传感器和探伤装置灵敏度的影响。针对在用的大多数浮动式传感器固定机构存在的两个严重缺点 ,提出采用自定位传感器固定机构 ,可消除机械装置对传感器灵敏度的影响。提出了一套标定和校验检测装置的方法 ,以保证探伤仪器的检测灵敏度始终恒定 ,提高检测结果的准确性和可靠性。     

Influence of thermal boundary conditions on natural convection in a square enclosure partially heated from below

Natural convection in air-filled 2D square enclosure heated with a constant source from below and cooled from above is studied numerically for a variety of thermal boundary conditions at the top and sidewalls. Simulations are performed for two kinds of lengths of the heated source, i.e., a small and a large source corresponding to 20% and 80% of the total length of the bottom wall, respectively. The Rayleigh number varied from 10³ to 10⁷. Results are presented in the form of streamline and isotherm plots as well as the variation of the Nusselt number and maximum temperature at the heat source surface. Comparisons among the different thermal configurations considered are reported.     

面向对象方法在7号信令软件设计中的应用

随着交换技术的飞速发展，程控交换软件的规模越来越大，改动也越来越频繁，如何使代码对数据的改动具有相对的稳定性成为程控软件设计的一个首要问题。本文以ＣＣＳ７（７号公共信道信令）为例，从对象模型、动态模型、功能模型３个方面阐述了ＯＯ（面向对象）方法在ＣＣＳ７软件设计中的应用。这一方法，也可应用于程控软件的设计。     

Intelligent control of doubly‐fed induction generator systems using PIDNNs

An intelligent control for a stand‐alone doubly‐fed induction generator (DFIG) system using a proportional‐integral‐derivative neural network (PIDNN) is proposed in this study. This system can be applied as a stand‐alone power supply system or as the emergency power system when the electricity grid fails for all sub‐synchronous, synchronous, and super‐synchronous conditions. The rotor side converter is controlled using field‐oriented control to produce 3‐phase stator voltages with constant magnitude and frequency at different rotor speeds. Moreover, the grid side converter, which is also controlled using field‐oriented control, is primarily implemented to maintain the magnitude of the DC‐link voltage. Furthermore, the intelligent PIDNN controller is proposed for both the rotor and grid side converters to improve the transient and steady‐state responses of the DFIG system for different operating conditions. Both the network structure and online learning algorithm are introduced in detail. Finally, the feasibility of the proposed control scheme is verified through experimentation. Copyright © 2011 John Wiley and Sons Asia Pte Ltd and Chinese Automatic Control Society     

Directions for improving manual fire suppression using a physically based computer simulation

The Swedish Fire Research Board and the U.S. Federal Emergency Management Agency are sponsoring a project to further the understanding of the basic mechanisms involved, as well as to support the development of standards for and to seek ways of improving the performance of portable fire suppression systems used by fire departments.This paper describes a physically based computer model developed to simulate one aspect of the problem: the manual suppression of postflashover fires. This includes: (1) an overview of the physical basis behind the model; (2) a comparison of model predictions with available experimental data, and (3) an analysis of fire suppression effectiveness using the model.The analysis concludes that, when direct access and extinguishment of the burning fuel is not possible, improved fire control occurs with water sprays having a Rosin-Rammler distribution of droplet sizes with volume-median-drop diameters in the 0.15 to 0.35 mm range. This agrees with available experimental data. It is also shown that fire fighting venting and standoff distance requirements may lead to more severe fires requiring more water for control; although venting and water spray induced air/gas flow also serve to channel hot steam and gases away from the fire fighter adding to his safety. The analysis also shows that allowing higher gas and surface temperatures at fire control through improved fire fighter protective clothing and equipment design reduces water flow rate requirements. Additional experimental work is recommended before all these conclusions are considered definitive. Reference: L. M. Pietrzak and G. A. Johanson, Directions for Improving Manual Fire Suppression Using a Physically Based Computer Simulation,Fire Technology, Vol. 22, No. 3, August, 1986, p. 184.