离散Hopfield神经网络和联想记忆的开关电流技术实现

研究了离散Ｈｏｐｆｉｅｌｄ神经网络（ＤＨＮＮ）和联想记忆神经网络的开关电流技术实现，利用多权输入跨导，开关电流延迟器（ＳＩＤ）和可编程电流比较器（ＰＣＣ）实现了离散Ｈｏｐｉｅｌｄ神经网络，并提出了利用离散Ｈｏｐｆｉｅｌｄ神经网络实现自联想记忆时相应的开关电流电路，所提出了开关电流神经网络适宜于超大规模集成，能在低电压（如３．３Ｖ）下工作。     

A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

潜油电动机滑行时间的自动测量

潜油电动机滑行时间是评定电动机装配质量的重要指标。鉴于手工测量电动机滑行时间存在效率低和误差较大的不足,设计了潜油电动机滑行时间自动测量系统。它通过分压电路和计算机自动测量系统测量潜油电动机定子上感应的电压变化状况,即可得到电动机滑行时间。用手工测量、波形分析和自动测量3种方法测量6种型号电动机的滑行时间,其中5种滑行时间长于3s,判定为合格;1种滑行时间短于3s,判定为不合格。3种方式测量的滑行时间具有较好的一致性,仅波形分析法得出的滑行时间比自动测量的滑行时间稍长,表明自动测量方法的精度和重复性可满足要求。     

同步电机转子的检修探讨

同步电动机转子时常由于磁极松动,导致电机振动现象严重.本文以烧结厂1#抽烟机转子检修为例对同步电机的转子检修进行探讨,很好的解决了这个问题.同时为同步电机转子检修提供了一整套检修方法.     

配网侧接入电源对负荷建模的影响

研究了配网侧接入电源对负荷建模的影响。发现当配网侧电源的发电容量逐渐增大时，原有的感应电动机并联恒阻抗、恒电流、恒功率（ZIP）模型的负荷模型将不再能很好地反映该区域的负荷特性，进而提出了一种新的负荷模型结构———异步发电机并联ZIP模型。通过仿真计算，验证了该新负荷模型的有效性，并进一步统一了上述2种负荷模型，称为异步机并联ZIP负荷模型。     

MPLS交换路由器的设计与实现

MPLS是目前Internet核心网上最看好的技术，基于Crossbar的高速交换技术的发展也很快，但是如何实现2种技术的有机结合以到达最优的性能却有一系列问题需要考虑。本文结合某MPLS路由器的设计项目，综合考虑了当前MPLS的标准以及有关交换结构的最新技术，对实现MPLS交换路由器进行了深入研究，并详细探讨了高速接口、排除和调度以及Crossbar等关键模块的设计和实现方案。     

自复中调速器在高水头高转速机组上的应用

简要介绍了自复中电/机调速器的机械和电气原理，并就使用该调速器的机组在生产运行中容易出现的停机后导叶开度漂移、停机时导叶不能完全关闭和显示开度与实际开度不一致等主要问题，通过修改可编程逻辑控制器（PLC）程序、调节调零杆位置、修改PLC程序参数等方法进行解决，这些方法对同类水电厂处理类似问题有借鉴作用。     

外转子电机关键技术及解决措施

对外转子电机的关键技术和主要工艺问题进行了探讨分析，并提出了解决措施。     

Minimum-Energy Translational Trajectory Generation for Differential-Driven Wheeled Mobile Robots

Mobile robots can be used in many applications, such as exploration, search and rescue, reconnaissance, security, and cleaning. Mobile robots usually carry batteries as their energy source and their operational time is restricted by the finite energy available from the batteries. Therefore, energy constraints are critical to the service time of mobile robots. This paper investigates the minimum-energy control problem for translational trajectory generation, which minimizes the energy drawn from the batteries. Optimal control theory is used to find the optimal velocity trajectory in analytic form. To demonstrate energy efficiency obtainable, we performed simulations of minimum-energy velocity control and compared the results with loss-minimization control and energy-optimal trapezoidal velocity profiles. Simulation results showed that significant energy savings can be achieved, of up to 9% compared with loss-minimization control and up to 10% compared with energy-optimal trapezoidal velocity profile. We also performed an actual robot experiment using Pioneer 3-AT platform to show the validity of the proposed minimum-energy velocity control. The experimental results revealed that the proposed minimum-energy velocity control can save the battery energy up to 10% compared with loss-minimization control. Categories (3): Robot control, (5): RobotMotion Planning     

天铁热力厂4#锅炉电气自动化控制系统

介绍了热力厂4^#锅炉电气系统与微机联络控制的方式。系统分别采用变频器485接口式电动机保护测控单元或接触器与微机连接，实现4^#锅炉电气控制过程。