混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。     

基于关键路径延时检测的自适应电压缩减技术

为了减小传统的最差情况设计方法引入的电压裕量,提出了一种变化可知的自适应电压缩减(AVS)技术,通过调整电源电压来降低电路功耗.自适应电压缩减技术基于检测关键路径的延时变化,基于此设计了一款预错误原位延时检测电路,可以检测关键路径延时并输出预错误信号,进而控制单元可根据反馈回的预错误信号的个数调整系统电压.本芯片采用SMIC180 nm工艺设计验证,仿真分析表明,采用自适应电压缩减技术后,4个目标验证电路分别节省功耗12.4％,11.3％,10.4％和11.6％.     

Design and performance study of phase‐locked loop using fractional‐order loop filter

The present work reports the realization of an analog fractional‐order phase‐locked loop (FPLL) using a fractional capacitor. The expressions for bandwidth, capture range, and lock range of the FPLL have been derived analytically and then compared with the experimental observations using LM565 IC. It has been observed that bandwidth and capture range can be extended by using FPLL. It has also been found that FPLL can provide faster response and lower phase error at the time of switching compared to its integer‐order counterpart. Copyright © 2014 John Wiley & Sons, Ltd.     

High-voltage and low specific on-resistance power UMOSFET using P and N type columns

For the first time, we present the unique features exhibited by power 4H–SiC UMOSFET in which N and P type columns (NPC) in the drift region are incorporated to improve the breakdown voltage, the specific on-resistance, and the total lateral cell pitch. The P-type column creates a potential barrier in the drift region of the proposed structure for increasing the breakdown voltage and the N-type column reduces the specific on-resistance. Also, the JFET effects reduce and so the total lateral cell pitch will decrease. In the NPC-UMOSFET, the electric field crowding reduces due to the created potential barrier by the NPC regions and causes more uniform electric field distribution in the structure. Using two dimensional simulations, the breakdown voltage and the specific on-resistance of the proposed structure are investigated for the columns parameters in comparison with a conventional UMOSFET (C-UMOSFET) and an accumulation layer UMOSFET (AL-UMOSFET) structures. For the NPC-UMOSFET with 10 µm drift region length the maximum breakdown voltage of 1274 V is obtained, while at the same drift region length, the maximum breakdown voltages of the C-UMOSFET and the AL-UMOSFET structures are 534 and 703 V, respectively. Moreover, the proposed structure exhibits a superior specific on-resistance (R_on,sp) of 2 mΩ cm², which shows that the on-resistance of the optimized NPC-UMOSFET are decreased by 56% and 58% in comparison with the C-UMOSFET and the AL-UMOSFET, respectively.     

Three-phase four-wire shunt active power filter based on the SOGI filter and Lyapunov function for DC bus control

The three-phase four-wire shunt active power filter (SAPF) was developed to suppress the harmonic currents generated by nonlinear loads, and for the compensation of unbalanced nonlinear load currents, reactive power, and the harmonic neutral current. In this work, we consider instantaneous reactive power theory (PQ theory) for reference current identification based on the following two algorithms: the classic low-pass filter (LPF) and the second-order generalized integrator (SOGI) filter. Furthermore, since an important process in SAPF control is the regulation of the DC bus voltage at the capacitor, a new controller based on the Lyapunov function is also proposed. A complete simulation of the resultant active filtering system confirms its validity, which uses the SOGI filter to extract the reference currents from the distorted line currents, compared with the traditional PQ theory based on LPF. In addition, the simulation performed also demonstrates the superiority of the proposed approach, for DC bus voltage control based on the Lyapunov function, compared with the traditional proportional-integral (PI) controller. Both novel approaches contribute towards an improvement in the overall performance of the system, which consists of a small rise and settling time, a very low or nonexistent overshoot, and the minimization of the total harmonic distortion (THD).     

Application of differential evolution for cascaded multilevel VSI with harmonics elimination PWM switching

Harmonic elimination pulse width modulation (HEPWM) method has been widely applied to multilevel voltage source inverter (MVSI) to remove low frequency harmonics from its output voltage. However, the computation of the HEPWM switching angles for MVSI is very challenging due to several constraints, namely angle sequencing, very tight angular spacing and the numerous possibilities of angles distribution ratio. Realizing the potential of Differential Evolution (DE) to handle complex problems, this work proposes its application to solve the HEPWM problem for cascaded MVSI. Its emphasis is on improving the availability of HEPWM for higher output voltage by extending the maximum range of modulation index (M). It also removes the discontinuities in the switching angles and reduces the number of distribution ratio required to obtain the required solution. Compared to the most advanced (similar) work, i.e., 7-level MVSI with seventeen switching angles, DE covers a wider range of M; the maximum achievable M is 2.80. Furthermore, it exhibits very low second order distortion factor (DF₂): for the worst case, the value of DF₂ is 0.0014%. To verify the viability of the proposed algorithm, simulation is carried out and hardware prototype is constructed. Both results show very good agreement with the theoretical prediction.     

继电保护中多路模拟量采集系统的设计

介绍了一种基于高性能浮点DSP芯片TMS320C32、CPLD芯片XC95288和A/D采样芯片AD976组成的多路采集系统的工作原理以及设计方法。通过对第一路施加特殊的电压量,在CCS开发环境下读取采样缓冲区的值,并利用Matlab对采样数据进行了全波傅氏变换。此外,该系统已在继电保护中得到广泛应用,实践表明,该系统能较好地解决多路模拟量的采集,并确保了采样数据的安全可靠性。     

Prediction of rock mass P wave velocity using blasthole drilling information

In this paper, the development of the models for the prediction of rock mass P wave velocity is presented. For model development, the database of 53 cases including widely used and recorded drilling parameters and P wave velocity was constructed from the field studies conducted in 13 open pit lignite mines. Both conventional linear, non-linear multiple regression and Adaptive Neuro Fuzzy Inference System (ANFIS) were used for model development. Prediction performance indicators showed that ANFIS model presented the best performance and it can successfully be used for the preliminary prediction of P wave velocities of rock masses.     

Effect of Moving Speed of Charged Metallic Spherical Electrode on Electrostatic Discharge

In this investigation, the nature of the electrostatic discharge (ESD) that occurs when a charged object moves toward a stationary grounded object is experimentally clarified. The spark lengths, discharge currents, and induced voltages in a magnetic probe were measured when a charged metallic spherical electrode connected to a 422 pF capacitor approached a stationary grounded object, which was the current target, for different moving speeds of the charged metallic spherical electrode in a range of 1 mm/s to 100 mm/s. The charge voltages of the capacitor were +6.5 kV and +10 kV. Based on the results, the average gap length shortened with the speed of the spherical electrode. The average peak values of the discharge current and the induced voltage were likely to increase with the speed of the spherical electrode. The average rise times of the discharge current and the induced voltage were likely to drop with the speed of the spherical electrode. The relation between the spark length and the discharge current due to the ESD can be explained qualitatively by using an equation derived from the spark resistance formula proposed by Rompe and Weizel.     

Voltage reference architectures for low-supply-voltage low-power applications

This paper presents a voltage reference generator architecture and two different realizations of it that have been fabricated within a standard 0.18 μm CMOS technology. The architecture takes the advantage of utilizing a sampled-data amplifier (SDA) to optimize the power consumption. The circuits achieve output voltages on the order of 190 mV with temperature coefficients of 43 ppm/°C and 52.5 ppm/°C over the temperature range of 0 to 120°C without any trimming with a 0.8 V single supply. The power consumptions of the circuits are less then 500 nW while occupying an area of 0.2 mm² and 0.08 mm², respectively.