金属管式换热器在气烧石灰竖窑上的应用

气烧石灰竖窑针对窑型产能较低、能耗较高的弊端,韶钢在新建气烧石灰竖窑上采用的双预热技术,使窑的产量提高47.5％,活性度提高每10min在20ml以上,能耗降低35.62％,经济效益明显.     

基于BOOSt结构下不连续导电模式的PFC电路

采用现代高频功率变换技术的有源功率因数校正（Power Factor Corrector,PFC)技术是解决高频开关变换器谐波污染的有效手段。与传统的PFC电路相比，有源PFC电路的输入电流接近正弦波且与输与电压同相位，能有效抑制电流波形畸变和谐波，因此避免了对同一电网设施的干扰。在PFC电路中，Boost变换器是研究和应用得最多的一种变换器。本文着重分析了Boost电路在不连续导电模式状态下，PFC电路的临界条件，对实际电路结构的设计有很好的指导意义。     

过氧化甲乙酮合成研究

论述了过氧化甲乙酮的合成方法，用阳离子交换树脂催化剂代替传统的无机酸催化剂。考察了离子交换树脂用量、反应温度对反应产率、活性氧含量的影响及溶剂对产品稳定性的影响。     

阴离子表面活性剂测定方法的探讨

本文对“阴离子表面活性剂的测定方法”进行探讨,优化了显色剂、萃取剂的用量及萃取频率等分析条件,有效地降低了方法的检出浓度,提高了分析精度及准确度,节约大量试剂。本法最低检出浓度的0.019mL/L。     

几种OLED有源驱动电路中像素单元电路的分析

在有机电致发光器件两管单元有源驱动电路的基础上．分析了几种四管单元电流控制型和电压控制型的驱动电路，它们都能补偿TFT阈值电压的漂移．但都有各自的优缺点：前者能准确地调节显示的灰度，但它的响应速度慢；后者的响应速度快，但不能准确地调节显示的灰度。     

用Tow-Thomas电路设计含有限非零传输零点有源滤波器的方法

Tow-Thomas电路是一种实现全极点滤波器的典型电路。本文给出了用Tow-Thoms电路设计含有限非零传输零点有源滤波器的方法，从而使Tow-Thomas电路可用于单片集成滤波器电路。而文中给出的公式可用于计算外接元件。设计实例表明了文中给出的计算公式的正确性。     

TCP/IP网络的动态模型描述

拥塞现象成为TCP/IP网络发展面临的一个重要问题。因此，拥塞控制对TCP/IP网络的鲁棒性和稳定性具有重要作用。目前，网络拥塞控制策略主要包括两类：端到端的控制机制，如TCP拥塞控制算法；网络内部的主动队列管理(AQM)策略。但由于缺乏对网络系统动态特性的了解，这些拥塞控制策略大都基于专家经验，并没有建立完整的理论分析框架。为此，本文从数据流的角度出发，通过建立网络基本单元状态方程模型来实现IP网络系统的数学解析模型，然后用混杂系统来描述TCP带有拥塞控制策略的数据传输过程，建立了TCP/IP网络的动态模型，为网络系统中动态性能的分析、拥塞控制策略的设计奠定了基础。实验结果表明，该数学模型与NS仿真实验的结果相一致。     

The Difference in Turbulent Diffusion between the Active and Passive Scalars in a Thermally Stably Stratified Medium

The difference in the turbulent diffusion between the active (heat) and passive (mass) scalars in a thermally stably stratified medium is investigated. The axisymmetric problem is treated on the formation of a turbulent circulation flow above a heated disk and on the turbulent diffusion of a passive scalar (impurity) from a continuous surface source in a stably stratified medium. The results indicate that the thermal stratification causes appreciable differences in the coefficients of turbulent transfer between the active (heat) and passive (mass) scalars. This means that the assumption of the identity of the coefficient of turbulent diffusion of heat and mass, employed in conventional models of turbulence, produces significant errors in estimating the heat and mass transfer in a thermally stably stratified medium.     

Level set and geodesic active contours based measurement of material removal between serial sections

The measurement of the thickness of material removed between serial sections is a crucial step of three-dimension reconstruction. Geodesic active contours is an efficient method for contour detection of objects on an image. The indents on the SiC/Al composite micrographs are segmented by using level set and geodesic active contours. After getting the contours of the indents, we calculate the distance from the uppermost pixel to the lowermost pixel to get the vertical diagonal length, and calculate the distance from the leftmost pixel to the rightmost pixel to get the horizontal diagonal length of each contour. Then the final length of each diagonal is acquired by averaging the vertical diagonal length and the horizontal diagonal length, respectively. The Vickers’ indenter is made by a square pyramidal-shaped diamond with opposite faces at an angle of 136°, so the thickness of material removed between two serial sections and the length difference of the diagonals on the two serial sections has a definite geometrical relation. Thus the thickness of material removed between two serial sections is acquired using the geometrical relation.