Comparison of a contactor catalytic membrane reactor with a conventional reactor: example of wet air oxidation

A wet air oxidation reaction was carried out in a gas/liquid catalytic membrane reactor of the contactor type. The oxidation of formic acid was used as a model reaction. The mesoporous top-layer of a ceramic tubular membrane was used as catalyst (Pt) support, and was placed at the interface of the gas (air) and liquid (HCOOH solution) phases.

A similar reaction was carried out in a conventional batch reactor, using a steering rate high enough to avoid gas-diffusion limitations, and exactly identical conditions than for the CMR (amount of catalyst, pressure, etc.). At room temperature, the CMR showed an initial activity three to six times higher than the conventional reactor. This activity increase was attributed to an easier oxygen access to the catalytic sites. Nevertheless, the catalytic membrane gradually deactivated after a few hours of operation. Different deactivation mechanisms are presented.     

热管及其在化工反应器中的应用

现代化工生产规模呈大型化趋势,要求更有效的传热元件来消除“放大效应”。简述了热管的工作原理及其在化工反应器中的应用。     

烯（醚）醛一步法合成异戊二烯技术开发—基础理论研究进展

本文介绍了烯(醚)醛一步法合成异戊二烯技术开发中,基础理论研究工作的进展,其中包括化学热力学、化学动力学、再生烧炭本征动力学和扩散动力学等理论研究。并针对该反应特征进行了化学反应规律和流动传递规律的研究。建立了流化床反应器数模和流化床再生器数模,为工程技术开发提供理论依据。     

固体颗粒对三相气升式环流反应器流动特性的影响

将液相视为连续相,气相和固相视为分散相,同时考虑各相之间的相互作用,结合气液固三相流体的动力学理论,建立气液固三相环流反应器三流体湍流流动的Eulerian模型.采用计算模拟软件Fluent对三相环流反应器的流动状况进行模拟,考察表观气速、固含率、颗粒大小对反应器的气含率以及液体流动速度的影响.模拟结果较好地解释了气升式环流反应器内的三相流体行为,模型与实验结果较好地吻合,表明了模型的可行性.     

DQ型高效催化剂在环管PP装置上的应用

介绍了使用DQ型球形高效催化剂在上海石油化工股份有限公司塑料事业部70kt/a环管连续法工业聚丙烯生产装置上应用研究的结果，并对结果进行了讨论。     

Cocurrent downflow circulating fluidized bed (downer) reactors — A state of the art review

In the last decade, cocurrent downflow circulating fluidized bed reactors, called “downer” reactors, have been proposed as an alternative to upflow circulating fluidized bed, or “riser”, reactors. In this paper, published results on downer studies are summarized and future directions of research are recommended. Downer reactors are shown to have several distinct advantages over upflow circulating fluidized bed reactors and can potentially be used in many industrial processes, mainly due to a more uniform gas and solids flow structure compared with risers.     

鲁奇甲醇生产装置数学模拟和工况分析——(Ⅰ)鲁奇副产蒸汽管壳型甲醇合成塔

以一氧化碳加氢和二氧化碳加氢为独立反应、甲醇和二氧化碳为关键组分,建立了鲁奇副产蒸汽管壳型甲醇合成塔催化床的一维拟均相数学模型,并求得管内各组分气体浓度和温度分布。讨论了不同操作条件对出口甲醇浓度和产量的影响。由于管外副产4.0MPa 的蒸汽,床层温度平稳。     

SBR反应器中反硝化条件下去除苯酚工艺

基于异养反硝化原理,在序批式间歇反应器(SBR)中对反硝化同时降解苯酚的菌种进行了149 d的驯化,驯化通过逐步提高进水中苯酚和NO3--N的浓度进行.驯化结束后,进水苯酚质量浓度达到360 mg/L,葡萄糖质量浓度达到100 mg/L,NO3--N质量浓度达到240 mg/L,水力停留时间6 h,苯酚和NO3--N去除率均大于98%.反应器运行结果表明:进水苯酚质量浓度低于720 mg/L时,SBR反应器运行稳定;高浓度NO2--N(＞60 mg/L)可以严重影响微生物对苯酚以及NO3--N的去除能力,同时反应器中20.5%～23.5%的COD可被用于微生物的细胞合成.     

Strong dependence on pressure of the performance of a Co/SiO2 catalyst in Fischer–Tropsch slurry reactor synthesis

A 10 wt% Co/SiO₂ catalyst was prepared by the incipient wet-impregnation method and tested in Fischer–Tropsch synthesis in a slurry reactor under conditions approaching industrial practice. The catalyst precursor was investigated by X-ray diffraction (XRD), temperature-programmed reduction (TPR), transmission electron microscopy (TEM) and photoelectron spectroscopy (XPS). The XPS and XRD techniques revealed the presence of a crystalline Co₃O₄ spinel-type phase, while-in addition-TEM and XPS analyses pointed to the formation of another amorphous Co₃O₄ spinel phase, both species interacting weakly with the silica substrate. The influence of total pressure on the conversion, selectivity and stability of the catalyst was studied. Upon increasing the overall pressure from 20 to 40 bar, not only activity increased but also the catalyst are not deactivating. These results are explained in terms of an increase of gases solubility in the solvent, this increment of CO concentration in the liquid phase favours carbonyl species formation and the cobalt particles segregation that implies an increase in the metal surface area.     

流化床电化学反应器研究进展

流化床电化学反应器是一种三维颗粒电极反应器,以其比表面积大、传质速率高而备受关注。就流化床电化学反应器在导电机理、数学模型、结构放大以及应用领域的研究现状和进展进行了综述,阐明了该类反应器开发、设计和模型化方面存在的问题,并提出了研究方向。