分析再热器超温爆漏与水冷壁结焦控制量的关系

文章介绍了宝钢自备电厂在改善锅炉燃烧工况，控制锅炉水冷壁结焦所采取的技术措施，分析了锅炉水冷壁结焦量与锅炉二次再热器烟气出口平均温度的关系，为解决锅炉水冷壁结焦所引发的二次再热器超温爆漏问题提供了依据。     

关于电视群信号对光纤副载波调频传输中的信噪比平衡问题的分析

本文对微波副载波用电视群信号调频的光纤传输中的信噪比平衡问题进行了分析,推导出VSB-AM信号在解调后的信噪比表达式,引入了信噪比恶化系数的概念.为了实现多路VSB-AM信号间的信噪比的平衡,相应的微波副载波频偏应有确定的比例关系.     

表面稳定模式铁电液晶的电光特性测试

采用一种改进的高分子膜摩擦定向法成功地实现了表面稳定模式铁电液晶的光学双稳态，对比度大于１４０，响应时间达１００微秒。     

Thermodynamic Analysis of Various Dehumidifying Dryers for Wood

Typical methods of dehumidification of air circulating in the dehumidifying driers (indirect and direct cooler and partial exchange of the air) were analysed. Energy aspect of cooler operation was evaluated. The method for minimization of unit thermal energy consumption in a dehumidifying drier by the optimal selection of the cooler point was also given. Methods of the heat recovery of heat conveyed in a cooler lending to save energy (heat regeneration. expansion and compression of the air, a dehumidifier) were analysed. It was indicated that introduction of dehumidifiers into contemporary wood driers caused significant improvement of energy aspects of their operation     

强度型光纤传感器的信号检测系统

本文阐述了一种可提高强度型光纤传感器测量精度的检测系统。该系统利用同一检测电路交替检测信号、参考通道的输出信号，并将信号、参考两通道的检测结果相除，从而消除了因发光二极管光源波动及检测电路系统不稳定所带来的误差。采用同步相关技术抑制了噪声，提高了输出信噪比。实验证明，当时间常数ＲＣ为０．０５Ｓ时，采用该检测系统可获得优于千分之一的零点稳定性和优于２×１０３的输出信噪比。     

Influence of two-step process and of different stoichiometric ratios on morphologies generated in castor oil epoxy resins

Phase separation during polymerization was studied in a model system consisting of a diepoxide based on diglycidyl ether of bisphenol A (DGEBA), variable amounts of ethylenediamine (EDA) and the mass of castor oil (CO) necessary to obtain a mass fraction equal to 0-15 in a final system where the stoichiometric ratio of amine to epoxy equivalents, r, was equal to 1. A two-step polymerization process was performed by curing first a system with r = 0-5, during variable times before phase separation, and then carrying the system to r = 1. Thermodynamic analysis of samples with different r values led to a linear relationship between the Flory-Huggins interaction parameter and r. The concentration (P) and average size (D?) of dispersed-phase particles followed opposite trends, i.e. P increased while D? decreased, when either r was increased or the time of curing in the first step of a two-step process was decreased. This was explained by assuming that the competition between nucleation and growth was determined by the viscosity at the cloud point, η_cp. Low values of η_cp favoured growth over nucleation and led to fewer but larger particles.     

无间隙原子钢的微观结构特征和塑性应变比

采用Ｘ射线衍射的ＯＤＦ和ＬＰ分析技术，ＳＥＭ电子通道花样和蚀坑技术观测，研究了超深冲无间隙原子钢板的微观结构特征。结果表明：控制化学成分、保证基体纯净、优选工艺参数，促进强的γ－〈１１１〉∥Ｎ．Ｄ纤维织构的形成是获得优异成型性的关键。用ＣＭＴＰ方法，由ＯＤＦ织构数据从理论计算了塑性应变比（ｒ），表明ｒｍ值高达３．１８。文中讨论了再结晶织构形成机制。     

90°分束偏光镜光强分束比研究

给出了90°分束偏光镜的e,o光光强分束比的计算公式,以及光强分束比随光波长的变化曲线;在6328Å测得的光强分束比与计算值是一致的。     

In-chain functionalization by alternating anionic copolymerization of styrene and 1-(4-dimethylaminophenyl)-1-phenylethylene

Anionic copolymerizations of styrene (M₁) with excess 1-(4-dimethyl-aminophenyl)-1-phenylethylene (M₂) were conducted in benzene at 25°C for 24h, using sec-butyllithium as initiator. Narrow molecular weight distribution copolymers with M?;_n = 16.1 × 10³ g/mol (M?_w/M?_n = 1.04) and 38.2 × 10³g/mol (M?_w/M?_n = 1.05), and 24 and 38 moles of M₂ per macromolecule, respectively, were characterized by size exclusion chromatography, ¹H NMR spectroscopy and DSC. The monomer reactivity ratio, r₁ = 5.6, was obtained from the copolymer composition at complete consumption of M₁, assuming that the rate constant k₂₂ =0,i.e. r₂ =0. The polymers exhibited T_g values of 128 and 119°C, respectively, which correspond to an estimated T_g = 217°C for the hypothetical homopolymer of M₂.     

含氮化合物废气选择性催化氧化技术研究进展

通过对当前含氮化合物废气治理技术的对比分析,总结选择性催化氧化的相关技术优势。根据对含氮化合物的种类及来源分析,介绍氨气、腈类、胺类及其他含氮化合物的催化净化技术。重点总结催化剂的种类、研发进展和在实际使用中可能遇到的问题,同时展望含氮化合物废气选择性催化氧化技术的研发方向。