酸化返出液中分离出的原油脱水时电脱水器跳闸原因及对策

海上油井酸化后,油井返排液沉降分离得到含酸原油,后者进入电脱水器后常引起电脱水器跳闸。其原因是含酸原油(油包水型乳状液)的电导率过高,超过了电脱水器的安全工作电导率κw。对于现场所用的电脱水器,由设计参数计算出κw=0.43μS/cm。从某海上油田3口油井酸化后不同时间的返排液共取样40份,随机选出13份,沉降分离后得到13份含酸原油样,测得电导率范围在0.03～10000μS/cm。认为原油的含水率(应<18%)不是引起跳闸的原因,跳闸的主因是含酸原油的高电导率。研制了一种油溶性的碱性添加剂,其化学成份是碱金属、碱土金属氧化物或氢氧化物,以浓溶液形式加入含酸原油中,可使电导率降至κw以下。加入量由实验确定。表2参2。     

真空钙热还原炉渣的综合利用研究

研究了从真空钙热还原炉渣中回收稀土的工艺条件；采用本工艺得到的合格稀土溶液，其回收率达65．41％；副产品氟化钙用作炼硅铁合金的助熔剂，使钙热还原炉渣得到综合利用。     

Boundary knot method for 2D and 3D Helmholtz and convection–diffusion problems under complicated geometry

The boundary knot method (BKM) of very recent origin is an inherently meshless, integration‐free, boundary‐type, radial basis function collocation technique for the numerical discretization of general partial differential equation systems. Unlike the method of fundamental solutions, the use of non‐singular general solution in the BKM avoids the unnecessary requirement of constructing a controversial artificial boundary outside the physical domain. The purpose of this paper is to extend the BKM to solve 2D Helmholtz and convection–diffusion problems under rather complicated irregular geometry. The method is also first applied to 3D problems. Numerical experiments validate that the BKM can produce highly accurate solutions using a relatively small number of knots. For inhomogeneous cases, some inner knots are found necessary to guarantee accuracy and stability. The stability and convergence of the BKM are numerically illustrated and the completeness issue is also discussed. Copyright © 2003 John Wiley & Sons, Ltd.     

A new bubble-point-pressure correlation for the binary LiBr/H2O solution

In accord with the increasing concern about the global environmental issues, the absorption refrigeration heat-pump systems are currently being considered very promising and attractive. For the purpose of supporting the advanced R&D technology in this area, we have developed a novel correlation to represent the bubble-point pressures of LiBr H₂O solutions. The developed correlation covers the most extensive range of validity ever proposed: 273–483 K for temperatures, 0.05 kPa to 1.0 MPa for pressures. and 29 76 wt% LiBr for concentrations.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994. Boulder, Colorado, U.S.A.     

Substituted uracils as corrosion inhibitors for copper in 3% NaCl solution

Substituted uracils were tested as corrosion inhibitors of copper in 3% NaCl medium using electrochemical polarisation, impedance measurements and non-electrochemical techniques (weight loss, IR and UV-visible). This study permitted to follow the evolution of the inhibitory effect of the uracil derivatives, according to their substituents, on copper in 3% NaCl medium. Comparison of results showed that dithiouracil (DTUr) was the best inhibitor. The maximum inhibition efficiency reached 98% at 10⁻³ M. DTUr adsorbs on the copper surface according to the Frumkin isotherm model.     

聚电解质溶液分子热力学模型

<正>链状聚电解质由于是长链大分子又有很高的电荷密度,其溶液即使在极低的浓度下仍具有很强的负偏差,与Debye-Huckel理论预测的结果相去甚远。工程上使用的Manning模型认为聚离子的电荷密度有一临界值,当超过临界值时,反离子即凝聚在聚离子表面使其实际电荷密度降至临界值。Nagvekar等在该模型的基础上引入NRTL方程,以计及短程相互作用的贡献。Manning等的方法虽然有一定的物理意义,但临界值的确定缺乏可靠的根据。     

多人决策的一类相对均衡解

本文分析由于决策人偏好不同而引起决策差异的多人多目标决策问题，提出了这类决策问题的一类相对均衡解的概念和求取方法。相对均衡解以决策群体偏好的加权集结为基础，能最大程度地反映每个决策人的偏好。文中研究相对均衡解的ＳＷＴ求取方法，并给出了求解的步骤。     

Fundamental solutions for half plane with an oblique edge crack

An elastic half plane with an oblique edge crack is considered in this paper. A pair of concentrated forces or point dislocations is assumed to act at an arbitrary point in the half plane. The half plane with an edge crack is first mapped into a unit circle by a rational mapping function so that the following analysis can be carried out on the mapped plane analytically. Then the complex stress functions are derived by separating the whole problem into two parts; one is the principal part corresponding to the infinite plane acted on by concentrated forces or dislocations, the other is the holomorphic part, which can be determined by making use of the property of regularity of complex stress functions. The stress intensity factors of the crack can be calculated with different inclined angles of the crack, and the displacement and stress components at an arbitrary position in the half plane can be expressed explicitly.     

A computational model for analysing interactive buckling and delamination growth in composite structures

In this paper, a unified method is presented: (i) to model delaminated stiffened laminated composite shells; (ii) for synthesising accurate multiple post-buckling solution paths under compressive loading; and (iii) for predicting delamination growth. A multi-domain modelling technique is used for modelling the delaminated stiffened shell structures. Error-free geometrically nonlinear element formulations — a 2-noded curved stiffener element (BEAM2) and a 3-noded shell element (SHELL3) — are used for the finite element analysis. An accurate and simple automated solution strategy based on Newton type iterations is used for predicting the general geometrically nonlinear and postbuckling behaviour of structures. A simple method derived from the 3-dimensionalJ-integral is used for computing the pointwise energy release rate at the delamination front in the plate/shell models. Finally, the influence of post-buckling structural behaviour and the delamination growth on each other has been demonstrated.     

超高压输电线路分裂导线通道模式理论分析

本对分裂导线传输电磁波的模式理论进行了分析，从所解特征根中选择一组最简单的模分量传递信息，并阐述了传输规律。