非晶Mg65-xNi21Pr14Agx合金电极的制备及其放电性能

用铜模喷铸法制备了非晶Mg65-x Ni21-Pr14Ag x合金,采用球磨方法细化了合金颗粒。系统研究了不同Ag含量对非晶合金电极充放电行为、放电容量、循环稳定性、高倍率放电等性能的影响规律。结果表明,Ag元素的添加改善了合金电极充/放电性能,随着Ag含量的增加,非晶合金电极的最大放电容量和循环稳定性均呈现先增大后减小的规律,其高倍率放电性能也有所提高,适量Ag的添加可明显改善非晶MgNi-Pr系合金的放电性能。     

变极性等离子弧焊铝合金厚板工艺研究

变极性等离子弧焊是一种新型焊接方法,由于等离子弧对焊接工艺和规范参数的变化比较敏感,获得良好焊缝接头的合理规范参数范围窄、裕度小.本文通过工艺试验,探讨了变极性等离子弧焊16mm铝合金厚板的技术可行性,论述了其相对于传统弧焊工艺的优点.     

Ag/LaNixCo1-xO3触点材料的制备及电接触性能研究

本文运用溶胶-凝胶燃烧法合成了双钙钛矿型LaNixCo1-xO3(LNCO)纳米材料,利用粉末冶金和热挤压技术制备了相应的Ag/LNCO触点材料及元件样品。重点考察了不同Ni、Co含量对Ag/LNCO触点材料微观结构、物相组成、物理性能、力学性能及电寿命服役能力的影响,对其电弧侵蚀失效行为进行了研究,并与SnO2粉体增强Ag基触点材料进行对比。结果表明:溶胶凝胶法合成的LNCO纳米颗粒粒径为20-30 nm,经粉末冶金工艺制备的Ag/LaNi0.5Co0.5O3触点材料电学性能和电寿命都优于Ag/SnO2触点材料,其电阻率低至2.10 μΩ?cm,电寿命性能达到51287次。表明Ag/LaNi0.5Co0.5O3触点材料性能较佳,是一种可以取代Ag/CdO的新型触点材料。     

Application of Magnetron Sputtering in Fabricating MEMS Microbatteries

With the development of MEMS and the electronic devices's miniaturization and integration, a new kind of power sources that can satisfy the need for high energy density is required. Microbatteries are being researched abroad for their advantages of extreme thinness and long-term power supply. The development of MEMS microbatteries are reviewed and suggestedmagnetron sputtering in fabricating a high-performance microbattery. The technics as annealing are analyzed. The microbattery with a LiNi1-x Cox O2 cathode exhibited stable cycle ability and a high specific discharge capacity, which was attributed to the alloying effect of the LiNiO2and LiCoO2.     

Synthesis of single-walled carbon nanotubes by arc-vaporization under high gravity condition

Arc-vaporization is one of the common methods to synthesize single-walled carbon nanotubes (SWNTs). However the detailed synthesis mechanism is still not clear, and the synthesis of longer and chirality-selected SWNTs has not been obtained. Here influence of the gravity G = 1 g₀, 2 g₀, and 3 g₀ is studied in order to develop the synthesis method of SWNTs. Simultaneously, calculations of heat convection are also carried out by using a fluid simulation program and the results are compared with the experimental results.     

Analysis of low energy arc discharge characteristics based on dynamic V-A characteristics model

Low energy arc discharge characteristics was analyzed based on dynamic V-A characteristics model. It draws conclusions that discharge time relates to the source voltage and the product of inductance and stable current, discharge time will increase when the source voltage increases; current reduce rate is in inverse proportion to the value of inductance; arc resistance when the arc occurs is the ratio of minimum arcing voltage to stable current. It also gains the expressions of arc resistance and arc power, arc resistance and arc power both increase as the source voltage increases and decrease as the value of inductance increases. Conclusions above mentioned are helpful to design intrinsically safe circuits.     

Electrode Evaporation Effects on Air Arc Behavior

A numerical study of the effects of copper and silver vapours on the air arc behavior is performed. The commercial software FLUENT is adapted and modified to develop a twodimensional magneto-hydrodynamic （MHD） models of arc with the thermodynamic properties and transport coefficients, net emission coefficient for the radiation model of 99% ai-1% Cu, 99% air-1% Ag, and pure air, respectively. The simulation result demonstrates that vaporization of the electrode material may cool the arc center region and reduce the arc velocity. The effects of Ag vapour are stronger compared to those of Cu vapour.     

变压器高压线圈表面发生电晕放电现象的分析探讨

对变压器高压线圈表面发生电晕放电现象进行了分析和探讨,并提出了处理及防范措施。     

超高压可控电抗器抑制潜供电流研究

笔者阐述了抑制潜供电流的意义和国内外的研究现状。针对潜供电流产生的机理及抑制措施进行了详细分析,介绍了可控电抗器的结构和基本工作原理,列出了四射线补偿方法下并联电抗器中性点小电抗器的计算公式,并建立了三峡右岸-江陵500 kV输电线路和可控电抗器模型,仿真研究了用可控电抗器取代常规并联电抗器后抑制潜供电流的效果。仿真结果表明,超高压可控电抗器能有效地抑制潜供电流。     

空冷机组排汽装置疏水改进方案

我国现在生产的空冷机组都将排汽装置与凝结水箱做成一个整体,这种设计方案具有占地省、系统简单等显著优点,所以能得到推广应用。