Lake-Level Change and Water Balance Analysis at Lake Qinghai,West China during Recent Decades

Lake Qinghai, the largest saline lake with an area of 4,260 km² (2000) and average depth of 21 m (1985) in West China, has experienced severe decline in water level in recent decades. This study aimed to investigate water balance of the lake and identify the causes for the decline in lake level. There was a 3.35-m decline in water level with an average decreasing rate of 8.0 cm year⁻¹ between 1959 and 2000. The lake water balance showed that mean annual precipitation between 1959 and 2000 over the lake was 357 ± 10 mm, evaporation was 924 ± 10 mm, surface runoff water inflow was 348 ± 21 mm, groundwater inflow was 138 mm ± 9 and the change in lake level was −80 ± 31 mm. The variation of lake level was highly positively correlated to surface runoff and precipitation and negatively to evaporation, the correlation coefficients were 0.89, 0.81 and −0.66, respectively. Water consumption by human activities accounts for 1% of the evaporation loss of the lake, implying that water consumption by human activities has little effect on lake level decline. Most dramatic decline in lake level occurred in the warm and dry years, and moderate decline in the cold and dry years, and relatively slight decline in the warm and wet years, therefore, the trend of cold/warm and dry climate in recent decades may be the main reasons for the decline in lake level.     

结晶器液面自动控制系统在唐钢板坯连铸机的应用

介绍了涡流法和同位素法2种结晶器钢水液面自动控制检测方式,及其在唐钢板坯连铸机的应用.     

镁法海绵钛生产工艺中大型无隔板镁电解槽的节能实践

以镁法海绵钛生产工艺中大型无隔板镁电解槽的实际节能情况为例，探讨了在镁电解生产中的非生产耗电、生产耗电、漏电等因素造成的能量浪费，阐述了生产中粗镁直流电耗、电流效率、工作电压3者之间的关系，指出了影响电解槽工作电压的有关因素及降低电解槽工作电压的途径。     

束流测量中的工频陷波器

提出了一种应用于电子束曝光机束流测量中的自动跟踪工频陷波器，给出电路结构，基于对其工作原理的分析，介绍了提高陷波器跟踪精度的设计要点及调试方法。     

双辊薄带钢连铸在线自动检测系统

介绍了双辊薄带钢连铸工艺,设计了双辊连铸机的计算机在线自动检测系统,通过采取正确的抗干扰措施提高了检测的精度,系统在双辊薄带钢连铸试验中应用效果良好.     

通用雷达故障诊断专家系统的设计

目的：为了提高雷达装备故障诊断的效率和可靠性。方法：通过对雷达装备综合测试和故障诊断要求和方法的分析。介绍一种适用于雷达装备的故障智能诊断专家模型，探讨了该模型的基本结构和相应的推理机制及故障诊断策略。结果：结论雷达故障诊断的特点，研究了该模型及诊断方法在雷达装备中的具体应用，证实了该方法是有效的。结论：将自动测试技术和专家系统相结合，可以提高故障诊断的效率和可靠性。     

降温集油技术在朝阳沟油田的应用

精确界定油井温度界限值,对回油温度进行自动控制是降低气耗、能耗的有效措施。首先推导了单井温度界限数值模型,然后针对朝阳沟油田的实际情况对油井进行了分类,并选择了有代表性的单(环)井进行了试验。通过现场实测值与利用模型计算的预测值比对,符合率达到了70%以上。在此基础上利用温度界限分析仪进行了进一步的验证试验,结果符合预期。在单(环)井上加装了掺水量自动控制装置,实现了回油温度的自动控制。     

Development of a Magnetic Suspension Densimeter and Measurement of the Density of Toluene

The development of a magnetic suspension densimeter that has been built for measurement of the density of compressed liquid at pressures up to 30 MPa in the temperature range 20 to 150°C is described. The densimeter was first built by the author and his coworkers at NIST. We describe here further improvements made on a second system built at NMIJ based on the same principle. The densimeter uses a small coil suspended from an electronic balance. Within the coil is placed a sample cell in which the pressurized sample and a buoy, which is a permanent magnet, are enclosed. For measurement of density, balance readings are recorded (1) with the buoy at rest and (2) with the buoy in magnetic suspension. The measurement procedure is basically a hydrostatic weighing, which is simpler than those of conventional magnetic densimetry. As an example, measurements of toluene density performed as part of an inter-laboratory comparison are presented. The data agreed with reliable literature values to within a few hundredths of a per cent.     

提高曲面近似展开精度的方法与实现

通过对不可展曲面近似展开精度的研究，提出了根据曲面曲率的大小对曲面自动进行网格划分，通过对综合展开误差数据场进行数据拟合来选取最优展开基点，基于空间曲面与其展开图间近似的等距变换关系进行展开样形的误差矫正等3种方法，这几种方法的实现在不同程度上有效地减小了曲面的近似展开误差，提高了曲面的近似展开精度。     

接地故障保护的设置和整定(三)

7 TT系统接地故障保护 TT系统的电源中性点直接接地,而电气设备的外露可导电部分则经各自的PE线接地。这样在大多数情况下,由于故障回路包括两个接地电阻,使接地故障电流太小,不足以使过电流保护动作切断接地故障电流。而且由于故障电流小,故障点未被熔焊,故障点阻抗是难以估计的接触电阻。因此,TT系统接地故障回路阻抗和故障电流难以估算。所以,必须设置漏电电流动作保护。