联合循环余热锅炉螺旋鳍片管烟气放热系数研究

东南大学建造了1座IGCC余热锅炉鳍片管受热面流动和传热热态试验装置,并先后在其上进行了2个不同螺旋鳍片管组的传热特性研究,通过分析比较实测的烟气侧对流放热系数与无量纲准则式计算的结果,得出了完全热模拟公式更为准确的结论。     

水质稳定剂LSH-406的研制及应用

针对中国石油格尔木炼油厂10万t／a甲醇装置循环冷却水系统水质差，换热器出现结垢、腐蚀等问题研制开发了水质稳定剂(水稳剂)LSH-406，并进行了工业应用。经过2个月的运行监测，结果表明，系统浓缩倍数大于4，20^#碳钢腐蚀速率小于0．075mm／a，不锈钢腐蚀速率为0．0005mm／a，每月污垢沉积速率小于15mg／cm^2。     

地面驱动螺杆泵恒液面控制方法

恒液面控制有利于提高泵效,降低抽油杆柱和泵等设备的失效率。为此结合地面控制装置,研究了一种控制方法和软件。该软件根据控制装置实时测量的转速、扭矩等参数并结合地层开采能力、杆泵型号等参数,分析计算出液面高度和控制范围,并计算出转速改变量,由控制装置实行闭环控制。经大庆油田5口井试验表明,液面高度误差均在50 m内,实现了螺杆泵恒液面控制目的。     

新建循环流化床锅炉运行研究

介绍了陆续新建或投产大批的发电机组，主要以循环流化床锅炉为主，由于这些新建机组投产试运行过程中前期准备不足或设备自身缺陷，导致机组不能正常运行，针对这些问题进行分析研究，以供借鉴。     

Calculation methods for comparing the performance of pure and mixed working fluids in heat pump applications

Three methods for comparing cycle performance of working fluids, pure as well as non-azeotropic mixtures, are investigated for two applications and for two mixture pairs, HCFC22-CFC114 and HCFC22-HCFC142b, and their pure components. The methods differ in the way of calculating the heat exchange processes. They assume, respectively, equal minimum approach temperatures, equal mean temperature differences and equal heat transfer areas. Changes of coefficient of performance (COP) with composition are explained for all methods. It is shown that transport properties must be taken into account when making rigorous comparisons between working fluids. To predict the relations between fluids with high accuracy, one must use the method with equal heat transfer areas. By the method with equal mean temperature differences, the COP can be estimated with the same accuracy for mixtures as for pure fluids, and can be used for rough estimations of the COP level with different fluids. The method of equal minimum approach temperatures should be avoided for non-azeotropic mixtures.     

以应力分析为基础的汽包封头强度计算

本文介绍应力分析设计法的原理，通过有限元计算得到汽包封头的温度场、应力场，并以应力分析为基础对汽包封头强度作了校核。     

NUMERICAL STUDY ON QUASI- STEADY FLOW OF NONNEWTONIAN FLUID IN SUCK-ROD PUMP

This paper presents a numerical method for simulation of the flow and thecalculated results of the quasi-steady axisymmetrical flow field and pressure distribution on valveball with power-law model for Non-Newtonian fluid in suck-rod pump.We believe the methodcan provide a foundation for further research and improvement of the design of suck-rod pump.     

用参数泵分步结晶制取精萘的新工艺及放大

采用参数泵分步结晶工艺，开发了直立弹状流气泡管结晶器，由工业萘提纯制取精萘。实验室研究和放大试验的研究表明，产品纯度大于９９％，收率大于９２．５％。弹状气泡强化了传热和传质过程，流体的均布是放大过程的关键。     

大泵站超驼峰水位运行压缩空气断流系统的设计方法

阐述了压缩空气断流的原理，提出了压缩空气断流装置的一般构成和设计方法，首次应用气体喷射器作为压缩空气减压增量变换器，不但及时地增加了补气量，防止断流后流道压力的下降，而且大大减小了储气罐容积，使该项技术得以满足工程实际的要求，为同类泵站的技术改造     

机油泵转子的研究

本文研究了有关机油泵转子的齿形曲线、测绘及型腔设计等几个问题