液化石油气磁力泵改造

对输送液化石油气磁力泵在运行1个月后出现的故障进行了分析,提出了在磁路、气路及安装等方面采取的一些改进措施。     

真空相变锅炉低排烟温度设计与低温腐蚀

真空相变锅炉是否会明显发生烟气低温腐蚀，一直众说不一。文章从锅炉发生低温腐蚀的机理人手，通过理论分析计算并通过实践检验，提出了真空相变锅炉虽然不能完全避免低温腐蚀问题，但不论排烟温度是否高于烟气露点，低温腐蚀的程度都很弱的观点；给出了真空相变锅炉沿烟气流程金属壁面的腐蚀速度与壁面温度的关系曲线，和烟气温度低于酸露点时金属壁面的腐蚀速度与壁面温度的关系曲线；同时，文章推荐真空相变锅炉的设计排烟温度取130℃左右的低排烟温度。根据上述观点设计的数百台产品已经过多年实际运行，未发现明显     

给水泵密封水系统对机组真空的影响

介绍了银川热电厂二期工程投运一年以后,多次出现凝汽器真空缓慢下降的现象。在机组系统严密性试验合格的前提下,经多次观察,发现是给水泵密封水系统漏空气造成的。在采取了一些相应措施后,解决了这个问题。     

电潜泵大修打捞配套工具研制

随着采液时间的延长,电潜泵井事故不断增加,仅辽河油田每年就有30口左右的电泵井需要转大修.由于没有专用的打捞工具,作业设备的能力有限,其处理事故的周期往往较长,效果不理想.因此,在已有φ139.7mm套管内电泵打捞工具的基础上,研制开发了φ177.8 mm套管内电泵打捞工具,解决了油田电泵打捞的难题.     

Research on Marine Boiler＇s Pressurized Combustion and Heat Transfer

The effect of pressure on combustion and heat transfer is analyzed. The research is based on the basic combustion and heat transfer theorem. A correction for the heat calculation method for pressurized furnace is made on the basis of the normal pressure case. The correction takes the effect of pressurizing into account. The results show that the correction is reasonable and the method is applicable to combustion and heat transfer of the marine supercharged boiler.     

SUPMAX500系统在锅炉控制系统中的应用

针对动力厂35t/h锅炉的工艺控制要求，选用SUPMAX500集散控制系统。介绍了系统的软、硬件构成及其具体实施方法。     

水喷雾灭火系统在电信枢纽工程燃气锅炉房的应用

分析了燃气锅炉的火灾危险性和水喷雾用于燃气锅炉消防的灭火机理,提出了水喷雾灭火系统的设计参数的选择、系统的控制方法以及在设计中可能涉及到的问题和注意事项,并结合工程实例进行了探讨。     

A continuum model for pumping performance of turbomolecular pumps in all flow regimes

In the present study a continuum model for one-dimensional plane Couette-Poiseuille flow is implemented to turbomolecular pumps in different flow regimes. Pumping performance of various turbomolecular pumps including 6 single rotors, a rotor-stator row, a rotor-stator-rotor row, and a multi-row with 13 alternative rotor-stator rows is considered here. The obtained results show that the model provides good quantitative values for pumping performance of turbomolecular pumps over the whole regimes ranging from molecular flow to transition to slip flow.     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

KMLS型立式砂泵的振动噪声产生原因及解决措施

针对KMLS型立式砂泵振动、噪声产生原因及其表现特征,提出了解决措施。通过对这些原因的分析研究,可以提供泵设计者和生产者在减少砂泵振动方面采取相应的措施,使KMLS型立式砂泵能更好的服务于用户。