The principle and fundamental characteristics of brushless three-phase synchronous induction motor with two stators

Brushless three-phase synchronous motor involving a rotating ac exciter on the same shaft as the motor and with the windings linked through a shaft-mounted rectifier is widely used as medium and large capacity machines. However, the motor needs to fit with damping windings for self-starting outside of the field winding in the rotor and needs to equip discharge resistance with complex electronic device to dispose of electromagnetic force induced in the field winding at starting. Therefore, the rotor structure is very complex, and there are disadvantages, especially for the robust and highly reliable motor that is desired. To solve the problem found in traditional motors, the authors proposed a brushless three-phase synchronous induction motor with two stators and one wound rotor. This problem is solved because the proposed motor is of two-stators structure: the rotor winding operates as a secondary winding of induction motor at starting and as the field winding at synchronous operation. The motor can self-start as a wound-rotor induction motor without external secondary resistance. Therefore, discharge resistance is not necessary; the starting equipment is very simple and the rotor structure is robust. It is possible to start with high torque. In this paper, the basic constitution of the proposed motor and the principles of operation are described in detail. The experimental results at starting and pulling into synchronism are shown for confirming the principles of operation and the experimental and numerical results of the starting characteristics. The load ones and the generating ones are shown and then the practical use of the proposed motor is confirmed.     

Effect of processing history on the properties of Ag-based tapes

The Bi-system tapes and coils were prepared by the powder-in-tube method. The effect of processing and heat treatment on the properties of the tapes and coils was studied. It is found that the shearing stress produced by the rolling process may destroy the 2223 phase, and the destroyed 2223 phase cannot be recovered by heat treatment, whereas the pressing stress produced by the uniaxial pressing process only makes the 2223 phase grains break, and the broken 2223 phase can be closed by the heat treatment. TheJ _c values of the rolling samples, pressing sample, and the coil with a diameter of 35 mm are over 1.3×10⁴, 2.5×10⁴, and 4×10³ A/cm² (77 K, 0 T), respectively.     

Reduction of Stibnite at Moderate Temperature

Reduction of stibnite with hydrogen in the presence of calcium oxide has been experimentally inves-tigated at moderate temperature. The results reveal that the effluent generated in the reduction pro-cess contains much less air-polluting substance H_2S, and that the reaction activation energy is63. 3 kJ/mol. The form of antimony changes considerably when the reaction temperature varies.     

高频脉冲微束等离子电弧温度场的测试及分析

本文首次采用单波长激光干涉技术，对恒定直流和高频脉冲电流微束等离子电弧温度场进行了测试，并做了分析比较。以电弧温度分布为基础分析了高频脉冲电流微束等离子电弧收缩、稳定的原因。     

The performance of a direct-sequence spread-spectrum acquisition system using a linear prediction filter for narrowband interference suppression

The coarse acquisition performance of a direct sequence spread-spectrum receiver is analyzed when a linear prediction filter is used for narrowband interference suppression. We show that once an appropriate matching strategy is identified, the linear prediction filter can provide favorable performance when narrowband interference is present over a considerable range of both interference power and bandwidth. In addition, the presence of the filter dramatically improves the performance over the case where there is no filter, except when the interference bandwidth and the power are both small (i.e., when the processing gain provides sufficient interference immunity without the filter). If long spreading sequences are used with moderately sized observation windows, the acquisition performance can be severely degraded when a parallel acquisition scheme is used due to the linear predication filter. We show, however, that a slower serial receiver will provide reliable performance.This work was supported in part by the Office of Naval Research under contract ONR N00014-91-J-1234, the Army Research Office under contract ARO DAAL03-91-0071, and the NSF Center for Ultra-High Speed Circuits and Systems (ICAS).     

High-field magnetic and transport critical current density of Sm-Ba-Cu-O: Agx superconductors at low temperature

Variation of magnetic critical current density (J _mc) and transport critical current density (J _tc) in high magnetic fields at liquid helium temperature were investigated on Sm-Ba-Cu-O: Ag _x (x=0.0, 0.2, 0.4, and 0.6) superconducting samples prepared by the coprecipitation technique.T _c and crystallographic parameters remain unaffected by Ag addition. However, bothJ _mc andJ _tc were found to increase on Ag addition. The volume pinning force (F _p) also increased with increase in Ag concentration, resulting in stronger flux line sheer. Microwave-induced d.c. voltage measurement shows a significant reduction of the total number of weak links between the superconducting grains with increasing concentration of Ag, which creates stronger pinning potentials between the boundary of the superconducting intergrains. Hence, the volume pinning force is greatly enhanced by Ag addition, leading to flux line lattice movement which is responsible for highJ _mc andJ _tc.     

本征吸除硅片特性研究

本文描述硅本征吸杂片的特性参数,如吸除区宽度、洁净度,氧沉淀密度、MOS电容寿命,介绍了表面态密度及残余间隙氧浓度的检测方法和工艺对参数的影响及参数之间的内在联系,文章还实验论证了不同参数水平对器件成品率的影响,建立了以MOS电容寿命为主导的参数控制方法,利用本文提供的控制参数,可使CCD-512器件成品率达60％,以上优品率≥85％。     

电机拆线固定装置的制作

针对传统拆线方法劳动强度大及不安全性,制作电机拆线固定装置,为车间的生产提 供安全保障。     

新型环氧树脂绝缘浸渍胶（WSK）在微特电机上的应用

介绍了新型环氧树脂少溶剂快干绝缘浸渍胶的性能试验数据及基在微特电机上的应用及注意事项。     

PTS瞬态流动与换热数值模拟研究

为了研究压水堆因“直接安注”冷水注入压力容器下降环腔而导致的承压热冲击（PTS）热工水力问题,基于1:10比例模型,应用计算流体力学软件FLUENT5.4进行了紊流流动换热的数值模拟分析,同时进行了常压瞬态传热实验研究。针对下降环腔折算流速0.5 m/s,安注流速10m/s的典型工况,研究了安注水开启后下降环腔内的瞬态流动换热特性,数值模拟与实验结果吻合良好。考察了压力容器安注接管出口区环形焊缝区及堆芯段筒体中子强辐照区所承受的热冲击状况,基于稳态流动研究了下降环腔内流体混合特性及流动机理,为热冲击分析提供参考。