A direct stiffness analysis of a composite beam with partial interaction

The use of the conventional semi-analytical stiffness method in finite element analysis, in which interpolation polynomials are used to develop the stiffness relationships, leads to problems of curvature locking when beam-type elements are developed for composite members with partial interaction between the materials of which it is comprised. The curvature locking phenomenon that occurs for composite steel–concrete members is quite well reported, and the general approach to minimizing the undesirable ramifications of curvature locking has been to use higher-order polynomials with increasing numbers of internal nodes. This paper presents an alternate formulation based on a direct stiffness approach rather than starting from pre-defined interpolation polynomials, and which does not possess the undesirable locking characteristics. The formulation is based on a more general approach for a bi-material composite flexural member, whose constituent materials are joined by elastic shear connection so as to provide partial interaction. The stiffness relationships are derived, and these are applied to a simply supported and a continuous steel–concrete composite beam to demonstrate the efficacy of the method, and in particular its ability to model accurately both very flexible and very stiff shear connection that causes difficulties when implemented in competitive semi-analytical algorithms. Copyright © 2004 John Wiley & Sons, Ltd.     

Analysis of the Ductile Strength of Welds Weakened by Notches in Longitudinally Welded Pipes of Large Diameter by the Method of Slip Lines

We study the stressed state of an inhomogeneous welded joint containing an interlayer of a more high-strength material under the action of tensile loads. It is assumed that the contact boundary has a cracklike defect. We deduce analytic dependences of the fracture load on the mechanical inhomogeneity of the joint, thickness of the interlayer, and depth of the defect. The maximum depth of the defect to which the joint is insensitive is established. The proposed theoretical results are innovative and agree with the experimental data obtained for specimens cut out from a pipe of 14KhGS steel.     

Controllability of One Spin and Two Interacting Spins

Mathematics of Control, Signals, and Systems - ?We consider the problem of steering control for the systems of one spin ½ particle and two interacting spin ½ particles in an...     

遗落的明珠——浅谈岑参山水写景诗的艺术价值

唐代诗人岑参以边塞诗闻名于中国古代诗坛，同时他的山水写景诗写得也毫不逊色，取得了极高的艺术成就，特别是其清淡、清新、清旷、清丽的“四清”并行的艺术风格尤为突出。由于历史和个人原因，岑参的山水写景诗历来鲜为人知，但这并不能否定其特有的艺术价值。     

氧气顶吹转炉溅渣护炉试验研究

采用水力模型研究方法 ,针对马钢 2 0t转炉进行溅渣护炉冷态模拟试验 ,得出最佳工艺参数为 :枪位 1680mm ,氮气流量为 110 0 0m3/h ,大流渣量 ,渣粘度适中。此外 ,在满足炼钢生产的条件下 ,采用夹角为 13°的喷头溅渣效果好     

矿石中金的快速测定

研究了活性炭纤维滤布富集分离的条件和解脱方法,并利用微波溶样、液珠萃取比色法测定矿石中的金。该方法的测定范围为(0.5~xx)×10-6,相对标准偏差RSD为3.2%,可用于矿石中金的野外快速测定。     

Fuzzy Multiobjective and Linear Programming Based Management Models for Optimal Land-Water-Crop System Planning

In this article, linear programming and fuzzy optimization models are developed for planning and management of available land-water-crop system of Mahanadi-Kathajodi delta in eastern India. The models are used to optimize the economic return, production and labour utilization, and to search the related cropping patterns and intensities with specified land, water, fertilizer and labour availability, and water use pattern constraints. Due to extreme backwardness of the study area, it has been decided to keep all the three objectives of the linear programming models at the same priority level to obtain the compromised solution in a fuzzy environment that incorporates the imprecision in fuzzy goals and fuzzy constraints. These non-structural models facilitate the conjunctive use of available surface water and groundwater resources. A comparative evaluation along with the benefit-cost ratios of the existing and proposed farming systems is also presented.     

难处理金矿石加石灰焙烧焙砂中CaS的消除

介绍了用空气氧化预浸加石灰焙烧焙砂中的CaS，以消除其对金氰化的影响。预浸后金的氰化浸出率可从58％提高到80％以上。     

有环境约束时完成一族跟踪任务的力控制

本文为工业机器人提出了一种极点配置控制法，这种控制方法的优点有：一是它的积分作用消除了机器人的微小扰动和稳态误差；二是能任意设置系统的极点，因此能保证闭环系统的稳定性和规定状态变量的暂态响应；三是加入了加速度反馈，抑制了由电枢电感所引起的机械手的振动，最后，给出了ＰＵＭＡ５６２机器人的计算机仿真和实验结果验证了此控制法的有效性。     

阳平关砂金矿精选厂尾矿综合回收的研究

本文详细的介绍了陕西省阳平关砂金矿精选厂尾矿金和其他可利用的矿物综合回收方法和最佳分选流程。