Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Expert system for dispatch control in restoration of ehv power system after complete blackout

Present-day power systems operate with high reliability, and it is rare that a blackout will extend over an entire system swiftly and securely. This paper considers automatic power supply to loads after a complete blackout of a system. First, taking into account characteristics of generators, loads, and initial power sources, a method is proposed of allocating several generators to each load in parallel to the system and supplying power to the load sequentially. Second, to remove the imbalance between supply and demand of power, a method is proposed of adjusting the amount of supply and generation according to a present imbalance and the sum of past ones. Third, to automatically issue orders for start-up, parallel, follow-up, stand-by, and stoppage of generators, several rules for each power station are set and an expert system is made based on them. Finally, the expert system is applied to a model power system, and it is verified that it can restore loads without any trouble for a complete blackout which occur at any time of a day and in any restoration pattern.     

浅议轨道交通直流牵引供电系统的构成及保护配置

介绍了城市轨道交通直流牵引供电系统的构成,详细叙述了直流牵引供电系统的主要电气设备及其连接方法,以及系统的运行方式.另外,还简单介绍了系统配置的直流保护以及保护原理和保护作用.     

BINELOCA 程序与广东岭澳核电站大破口失水事故分析

ＢＩＮＥＬＯＣＡ程序是在吸收国外先进大破口失水事故分析计算机程序的基础上，针对我国现有大破口失水事故分析程序的不足和工程应用方面的问题，采用了一些成熟的、新型的和当今国际公认的瞬态热工水力数学物理模型以及水和蒸汽性质参数计算公式改编而成的大破口失水事故分析程序。通过对广东岭澳核电站大破口失水事故的计算表明，ＢＩＮＥＬＯＣＡ程序计算的结果与法国计算的结果是一致的。     

Characteristics and classification of high-current fault arcs on distribution systems

When a fault occurs on transmission or distribution systems due to lightning or overvoltage, often an arc discharge occurs at the fault point. The arc discharge, which is caused by a fault current, has a high current, high temperature, strong light emission, etc., thus it sometimes causes heavy damages to electric power equipment. The arc discharge is influenced by the conditions around the arcs, i.e., gas, insulation materials, gap length, weather, etc. Also, the arc voltage along the arc column indicates the characteristics of the arc. If the voltage waveforms of the arcs caused by the fault on transmission or distribution systems are classified, it is possible to find the location and the equipment where the fault occurred. In this paper, the arc voltage data in 6-kV class XLPE cables and 6-kV class overhead lines are analyzed and an artificial neural network method is applied to classify the arc voltage waveforms. The results obtained from the six artificial neural networks developed show that the artificial neural network method is effective for classification of arc voltage waveforms if adequate input parameters are selected.     

堆底熔穿事故的场外后果及其对策

在压水堆核电站应急计划和应急响应中，堆底熔穿事故占有重要位置。本文用法国核电厂事故源项Ｓ３（对应于堆底熔穿事故）计算了在典型气象条件下的场外放射学的后果，根据一般防护决策原则和我国颁布的干预水平，提出了保护公众的应急防护措施的建议。     

The magnetic applications choice among ferrite ceramics,metallic strips,or metal powder cores

Iron-based metallic strip materials such as iron, silicon-iron, and amorphous metal are used for low frequency (50–60 Hz. line) power applications. Low-loss Nickel-based alloys as high permeability strip or insulated powder cores are the choices for stable, low-level higher frequency applications. Iron-based powder cores offer low cost as power supply filter chokes. Ceramic ferrites combine highest frequency operation with low cost and reduced component size as transformers and chokes in telecommunication and high frequency power supply applications.     

圆盘式高速金属冷锯机锯切功率的实验研究

对１６００圆盘式高速金属冷锯机进行了锯切功率的实验研究。对某厂四种有代表性的产品，用不同的进锯速度，实测每种条件下的锯切功率变化，和最大瞬时锯切功率与平均锯切功率之比。并以实测数据为基础，得出每种产品以进锯速度为自变量的平均锯切功率回归公式。这些工作，不仅可以为这种冷锯机锯切功率的理论研究提供依据，还可直接为使用和设计这种冷锯机给出具体参考数据。     

新型高性能脉冲峰值保持电路

本文介绍了两种新型跨导型脉冲峰值保持器，分别用于多丝正比室（ＭＷＰＣ）和复合晶体闪烁探测器（Ｐｈｏｓｗｉｃｈ）输出脉冲信号的形状和幅度分析。电路的跨导放大级采用跨导型集成运算放大器，使电路结构简单化，且性能优良可靠，能响应输入脉冲最小上升时间分别为５０ｎｓ（Ｐｈｏｓｗｉｃｈ）和５００ｎｓ（ＭＷＰＣ）的信号，在４０ｄＢ的动态范围内，两电路的积分非线性均好于０．１％，特别适用于空间γ射线观测。     

A calibration method for the energy-integrating function in photovoltaic system monitoring

Solar radiation has an irregularly varying factor due to a basic day and night cycle and climatic conditions. For such conditions a data sampling interval is important to ensure the accuracy of energy monitoring in a photovoltaic system. While treating a system monitoring equipment as a black box. the author has developed the method of calibrating an energy-integrating function. At first for various input waveforms, the relationship between sampling intervals and quasi-integration outputs have been examined by trapezoidal rule. In the numerical simulation the phases of the sampling clock also are considered Then it is concluded that a sampling interval can be inspected through outside observation only by using a rectangular single pulse. By applying the pulse to the energy-integrating process, two kinds of integrated outputs can be obtained for different sampling phases. The calculated difference between both outputs can uniquely give the sampling interval being inspected. Conditions to ensure measuring accuracy are discussed and the validity of this method has been demonstrated experimentally. Practical calibrating procedures also are proposed for the integrating function of PV system monitoring.