锚网钢带支护在煤巷掘进中的应用

石门穿煤采用锚网钢带喷碹联合支护,是巷道支护方式的一项改革,同时也为今后回采巷道支护提供了技术依据。     

夏70－斜05井落井电缆打捞工艺

夏７０－斜０５井完钻电测时３３９７ｍ长的电缆断落井内。使用自制外捞绳器和磨鞋历时７４０ｈ成功地将落井电缆全部打捞出井，避免了该井的报废，挽回了近２００万元经济损失。文中较详细地介绍了打捞作业的难点及打捞工具的制作，最后针对电缆事故的处理提出了几点认识。     

基于SIR的同轴腔体带通滤波器设计

基于阶跃阻抗谐振器SIR(stepped impedance resonators)的基本原理,采用λg/4型SIR作为基本谐振单元,设计了一款小型化同轴腔体带通滤波器.仿真结果显示,相比实际长度λg/4该滤波器尺寸压缩了56.7%,通带内回波损耗小于-17.5 dB,插入损耗小于0.1 dB,带外抑制度达到了-38.8 dB,满足了现代通信系统对滤波器小型化、低插入损耗、高选择性的要求,能够广泛应用于现代移动通信系统.     

基于深度强化学习的动态装配算法

针对动态装配环境中存在的复杂、动态的噪声扰动,提出一种基于深度强化学习的动态装配算法。将一段时间内的接触力作为状态,通过长短时记忆网络进行运动特征提取;定义序列贴现因子,对之前时刻的分奖励进行加权得到当前时刻的奖励值;模型输出的动作为笛卡尔空间位移,使用逆运动学调整机器人到达期望位置。与此同时,提出一种对带有资格迹的时序差分算法改进的神经网络参数更新方法,可缩短模型训练时间。在实验部分,首先在圆孔–轴的简单环境中进行预训练,随后在真实场景下继续训练。实验证明提出的方法可以很好地适应动态装配任务中柔性、动态的装配环境。     

用电磁波速诊断XLPE电缆绝缘

XLPE电缆绝缘诊断的研究对于掌握电缆的绝缘老化状态,保证电力传输系统的安全可靠运行有着十分重要的意义。针对工程实际中大规模应用的诊断方法不多见的现状,提出了一种XLPE电缆状态检测的新方法,即用电磁波在一段XLPE电缆中的传播速度作为诊断这段电缆是否发生老化的依据。在阐明了该方法的原理和理论依据后介绍了所搭建的实验平...     

Development of the bus joint for the ITER Central Solenoid

The terminations of the Central Solenoid (CS) modules are connected to the bus extensions by joints located outside the CS in the gap between the CS and torodial field (TF) assemblies. These joints have very strict space limitations. Low resistance is a common requirement for all ITER joints. In addition, the CS bus joints will experience and must be designed to withstand significant variation in the magnetic field of several tenths of a Tesla per second during initiation of plasma. The joint resistance is specified to be less than 4 nΩ.The joints also have to be soldered in the field and designed with the possibility to be installed and dismantled in order to allow cold testing in the cold test facility. We have developed coaxial joints that meet these requirements and have demonstrated the feasibility to fabricate and assemble them in the vertical configuration. We introduced a coupling cylinder with superconducting strands soldered to the surface of the cable that can be installed in the ITER assembly hall and at the cold test facility. This cylinder serves as a transition area between the CS module and the bus extension.We made two racetrack samples and tested four bus joints in our Joint Test Apparatus. Resistance of the bus joints was measured by a decay method and by a microvoltmeter; the value of the current was measured by the Hall probes. This measurement method was verified in the previous tests. The resistance of the joints varied insignificantly from 1.5 to 2 nΩ.One of the challenges associated with a soldered joint is the inability to use corrosive chemicals that are difficult to clean. This paper describes our development work on cable preparation, chrome removal, compaction, soldering, and final assembly and presents the test results.     

大跨度悬吊索系结构目标位置成形分析方法

针对大跨度悬吊索系结构,建立了一种精确的结构成形分析方法棗目标位置成形分析方法,并将这种方法应用于大跨度悬吊索系结构和索穹顶结构。分析结果表明,提出的分析方法理论正确、计算高效,并具有很高的精度,可作为结构成形分析的一种有力工具。     

悬索桥用大直径螺杆的生产工艺

悬索桥主缆采用AS法架设时,其锚固螺杆将承受较大的股靴拉应力作用.为保证锚固系统的安全,一般可通过增大螺杆直径来提高其承载力.但大直径螺杆制造难度较大,且缺乏成熟的制造工艺.为确定合理的大直径螺杆制造工艺,以阳宝山大桥φ150 mm的大直径螺杆为例,讨论了悬索桥用大直径螺杆制造工艺.螺杆选材为淬透性能良好的40CrNi...     

高压系统接地在Y/Y变压器中压侧引起的传递过电压

分析了某电厂110 kV Y y d三圈变压器在110 kV侧发生接地时造成35 kV系统的传递过电压引发事故的原因,建议该类35 kV系统中性点应采用小电阻接地或消弧线圈加并联阻尼电阻接地方式.