An examination of the effect of composite constituent properties on the notched-strength performance of composite materials

The effect of matrix and fiber properties on the strengths and failure processes of notched, continuous-fiber composite specimens has been investigated. Bearing, open and filled hole tension and compression tests were conducted on AS-4/3501-6, IM-8/3501-6, AS-4/APC-2 and IM-8/APC-2 specimens. Failure characteristics of tested specimens were studied by fractographic techniques. Failure progression was tracked by means of incremental loading, radiography and fractographic inspection.     

Al2O3/TiB2/SiCw三元复合材料的力学性能及显微结构

以Al₂O₃为基体,SiC晶须和TiB₂颗粒两种增韧剂,采用热压烧结工艺制备了Al₂O₃/TiB₂/SiC_w三元复合陶瓷材料。研究了热压工艺参数对材料致密度的影响和晶须含量对该复合材料的力学性能和显微结构的影响。结果表明;随晶须含量的增加,该复合材料的热压温度和保温时间需要相应的增加;晶须拔出、裂纹偏转和晶须的桥接为该复合材料的主要增韧机理;随晶须含量的增加,该材料的室温断裂韧性增加;该材料的断裂韧性随温度的升高而呈增大趋势,并且晶须含量越高,材料的高温断裂韧性增幅越大。     

Thin conducting polypyrrole film on insulating surface and its applications

An electrically conductive plastic material was obtained by the polymerization of pyrrole on insulating polymeric materials and nylon cloth impregnated with the oxidant by vapour phase technique, resulting in a uniform, smooth and adherent coating of conducting polymer having a surface resistance ranging from 200 Ω/□ to 20 kΩ/□, which makes it suitable for applications as an antistatic material.     

基体改性对C/C复合材料性能影响的研究(一)

本文从C/C复合材料的基体入手,研究了基体沥青、焦炭中添加氧化物的工艺条件及其在复合材料中的作用.结果表明,添加氧化物对基体改性,不仅能提高C/C复合材料的高温抗氧化性,也能对其它性能带来很大影响.只要控制适当的工艺条件,就可以得到高性能的C/C复合材料.     

The effect of fibre alignment on composite strength: II. The strength of angle-ply laminates

Experiments have been carried out on relatively wide angle-ply laminate samples with very short gauge lengths. These proved to be very much stronger than samples tested in earlier work, and which form the basis for our present design with these materials. It is highly likely that the early results for strength were more indicative of edge effects than true laminate strength. This is confirmed by data from tests on pressurized tubes. A review of the literature on this shows that such tests produced results which can be an order of magnitude higher than the early laminate tests. Thus our design calculations could well be severely underestimating the potential strength of angle-ply laminates. This may be having serious consequences for the aerospace industry, through the use of design criteria for strength which may be too conservative. Single-fibre experiments may pave the way for more realistic estimates of angle-ply laminate strengths. These indicate that a simple one-third power rule can be used to estimate the potential strength. However, this is purely ad hoc at present, and needs to be put on a firmer footing through both theoretical and experimental studies. Furthermore, if this approach is adopted, edge effects will still have to be allowed for, and estimated on the basis of the aspect ratio of the part.     

武钢 3×10~4m~3/h 空分手动变负荷生产的探索与实践

对武钢引进的两台３×１０４ｍ３／ｈ空分设备，为改变其自动变负荷生产调节范围小、时间长的问题，采用了人工手动变负荷的操作方法。实践表明：扩大了增减产范围，缩短了调节时间，有十分明显的综合经济效益，可供大型空分变负荷生产借鉴参考。     

Pultruded fibre reinforced polyurethane composites II. Effect of processing parameters on mechanical and thermal properties

This paper presents a novel process for the fabrication of pultruded polyurethane (PU) composites. The effects of the processing parameters on the mechanical properties (flexural strength and flexural modulus, etc.) and thermal properties (HDT) of the fibre reinforced PU composites by pultrusion have been studied. The processing parameters investigated include pulling rate (in-line speed), die temperature, filler type and content, and post-cure time and temperature. Results show that the composites possessed various optimum pulling rates at different die temperatures. On the basis of the DSC diagram, the swelling ratio, the mechanical properties and the thermal properties of composites, the optimum die temperature can be determined. It is found that the mechanical and thermal properties increase with filler content for various types of filler. The mechanical and thermal properties increase at a suitable post-cure temperature and time. Furthermore, the properties which decreased due to the degradation of composite materials for a long post-cure time will be discussed.     

SiC粒子增强铸造Al基复合材料的研制

本文用真空烘烤封罐法对 SiC 粒子进行预处理,在固液两相区内搅拌添加,制造了铸造 Al 基复合材料。测试表明,该复合材料具有铸造性能好,力学性能高的优点,适用于采用压铸、石膏型精密铸造、金属型铸造等工艺方法成型的活塞、连杆等要求苛刻的零件。     

分离有机/有机混合物的PVA、CA系列膜及其渗透汽化性能研究(Ⅱ) 成膜条件对渗透汽化性能的影响

用溶剂完全蒸发法制备了PVA复合膜 .经对MTBE/MeOH混合物的分离实验得到了PVA复合膜的最佳成膜条件 ,即 :铸膜液中PVA、马来酸浓度分别为 7%、3% ,热处理温度130～ 15 0℃ .在 1%～ 2 %丙酮水溶液中浸泡处理 4～ 8h ,CTA中空纤维RO膜被改性成渗透汽化膜 .CTA中空纤维膜的分离性能优于其它醋酸纤维素系列膜 ,PVA/CA复合膜的性能优于PVA/PAN复合膜和CA/PAN复合膜     

Effect of the particle size ratio on the conductivity of conductor-insulator powder composites: Numerical simulation

A theoretical method for determining the percolation limit and effective conductivity of composites based on polydisperse mixtures of insulator and conductor powders is proposed. The effect of the particle size ratio between the insulator and conductor on the percolation limit and effective conductivity is studied. Numerical simulation of the microstructure, effective properties, and percolation limit in composites is discussed. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 1–2(453), pp. 31–40, 2007.