Mass Transfer in a Flat Gas/Liquid Interface using non‐Newtonian Media

Gas/liquid mass transfer has been investigated using a stirred vessel gas/liquid contactor using non‐Newtonian media and carbon dioxide as absorbent and gas phase, respectively. The volumetric mass transfer coefficients at different operational variables have been determined. Non‐Newtonian media (liquid phase) were prepared as aqueous solutions of sodium carboxymethyl cellulose salt. The influence of the rheological properties, polymer concentration, stirring rate, and gas flow rate on mass transfer was studied for these liquid phases. Kinematic viscosity and density experimental data were used to calculate the average molecular weight corresponding to the polymer employed. The Ostwald model has been used to fit the rheological behavior of aqueous solutions of the polymer employed as absorbent phase. Reasonably good agreement was found between the predictions of the proposed models and the experimental data of mass transfer coefficients.     

超高压大容量铝电解电容器的研制

分析了大功率设备用超高压大容量铝电解电容器的特点,通过研制工作电解液、制订制作工艺及零部件设计方案,研制出的超高压大容量铝电解电容器具有损耗角正切小(tgδ为0.25)、承受纹波电流能力强(100 Hz,2.12～27.8 A)及寿命长的特点,耐久性达到85℃,5 000 h。     

Extracting Light from Polymer Light‐Emitting Diodes Using Stamped Bragg Gratings

In this paper, we describe a method for increasing the external efficiency of polymer light‐emitting diodes (LEDs) by coupling out waveguided light with Bragg gratings. We numerically model the waveguide modes in a typical LED structure and demonstrate how optimizing layer thicknesses and reducing waveguide absorption can enhance the grating outcoupling. The gratings were created by a soft‐lithography technique that minimizes changes to the conventional LED structure. Using one‐dimensional and two‐dimensional gratings, we were able to increase the forward‐directed emission by 47 % and 70 %, respectively, and the external quantum efficiency by 15 % and 25 %.     

Platinum Binuclear Complexes as Phosphorescent Dopants for Monochromatic and White Organic Light‐Emitting Diodes

Efficient blue‐, green‐, and red‐light‐emitting organic diodes are fabricated using binuclear platinum complexes as phosphorescent dopants. The series of complexes used here have pyrazolate bridging ligands and the general formula C^∧NPt(μ‐pz)₂PtC^∧N (where C^∧N = 2‐(4′,6′‐difluorophenyl)pyridinato‐N,C^2′, pz = pyrazole ( 1 ), 3‐methyl‐5‐tert‐butylpyrazole ( 2 ), and 3,5‐bis(tert‐butyl)pyrazole ( 3 )). The Pt–Pt distance in the complexes, which decreases in the order 1 > 2 > 3 , solely determines the electroluminescence color of the organic light‐emitting diodes (OLEDs). Blue OLEDs fabricated using 8 % 1 doped into a 3,5‐bis(N‐carbazolyl)benzene (mCP) host have a quantum efficiency of 4.3 % at 120 Cd m^–2, a brightness of 3900 Cd m^–2 at 12 V, and Commission Internationale de L'Eclairage (CIE) coordinates of (0.11, 0.24). Green and red OLEDs fabricated with 2 and 3 , respectively, also give high quantum efficiencies (～ 6.7 %), with CIE coordinates of (0.31, 0.63) and (0.59, 0.46), respectively. The current‐density–voltage characteristics of devices made using dopants 2 and 3 indicate that hole trapping is enhanced by short Pt–Pt distances (< 3.1 Å). Blue electrophosphorescence is achieved by taking advantage of the binuclear molecular geometry in order to suppress dopant intermolecular interactions. No evidence of low‐energy emission from aggregate states is observed in OLEDs made with 50 % 1 doped into mCP. OLEDs made using 100 % 1 as an emissive layer display red luminescence, which is believed to originate from distorted complexes with compressed Pt–Pt separations located in defect sites within the neat film. White OLEDs are fabricated using 1 and 3 in three different device architectures, either with one or two dopants in dual emissive layers or both dopants in a single emissive layer. All the white OLEDs have high quantum efficiency (～ 5 %) and brightness (～ 600 Cd m^–2 at 10 V).     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

An Analysis of Citation Counts of ETRI‐Invented US Patents

From its foundation until 2004, ETRI has registered over 1,000 US patents. This letter analyzes the characteristics of these patents and addresses the explanatory factors affecting their citation counts. For explanatory variables, research team related variables, invention specific variables, and geographical domain related variables are suggested. Zero‐altered count data models are used to test the impact of independent variables. A key finding is that technological cumulativeness, the scale of invention, outputs in the electronic field, and the degree of dependence on the US technology domain positively affect the citation counts of ETRI‐invented US patents. The magnitude of international presence appears to negatively affect the citation counts of ETRI‐invented US patents.     

Discrete Wavelet Transform: Architectures, Design and Performance Issues

Due to the demand for real time wavelet processors in applications such as video compression [1], Internet communications compression [2], object recognition [3], and numerical analysis, many architectures for the Discrete Wavelet Transform (DWT) systems have been proposed. This paper surveys the different approaches to designing DWT architectures. The types of architectures depend on whether the application is 1-D, 2-D, or 3-D, as well as the style of architecture: systolic, semi-systolic, folded, digit-serial, etc. This paper presents an overview and evaluation of the architectures based on the criteria of latency, control, area, memory, and number of multipliers and adders. This paper will give the reader an indication of the advantages and disadvantages of each design.     

Synthesis and photosensitivity of acryloylmorpholine copolymers with a pendant (meth)acryloyl group

We have developed new photopolymers that have superior waterproof properties and that can easily interact with polyfunctional acrylate compounds, thus serving as hydrophobic photocrosslinking reagents. Acryloylmorpholine monomers whose homopolymers were less moisture absorbing than the usual water‐soluble polymers but were still water soluble to a good degree, were copolymerized with other acryloyl monomers. We then introduced the photosensitive (meth)acryloyl group to side chains of the resulting polymers. Among six copolymers examined, the copolymers composed of acryloyl morpholine, hydroxyethyl acrylate, ethyl, or methyl methacrylate, and methacryloyl isocyanate were found to have nicely balanced hydrophilicity and waterproof properties, in addition to good compatibility with hydrophobic photocrosslinking reagents. The composite polymers thus obtained were confirmed to be promising photopolymers usable even in a highly humid environment. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 684–692, 2003