通用布缆系统标准化现状与分析

分析了通用布缆系统的基本组成结构，对每一部分的主要功能作了说明。总结了国内外通用布缆系统标准化体系的状况，重点描述了北美、欧洲以及国际通用布缆系统标准体系。回顾了国内通用布缆系统标准化的历程，重点分析了国内通用布缆标准化工作的特点和未来通用布缆标准化工作方向。     

基于循环前缀的单载波直接序列扩频技术(CP/CDMA)

介绍了下行链路中基于循环前缀的单载波直接序列扩频技术(CP/CDMA)。这种技术结合了多载波系统中的循环前缀和频域均衡,具有较低的复杂度。同时保留了单载波系统发射端复杂度低的优点。在时变信道中,利用基于辅助数据的信道估计方法,即每隔一定帧数的数据帧发送一帧训练序列来估计信道。在仿真中使用了信道编码。     

在无铅环境中的热风整平

当电子工业走向无铅焊接的时候,热风焊料整平仍然是继续可焊性保护的优选方法。     

添加剂对工业齿轮油性能影响的研究

研究了硫化烯烃、磷酸酯胺盐、硫磷酸酯极压抗磨剂,含氮杂环衍生物多功能添加剂和防锈剂等,对工业齿轮油抗乳化性能、极压抗磨性能、防锈性能的影响;以及硫化烯烃、磷酸酯盐极压抗磨剂与含氮杂环衍生物多功能添加剂之间的协和效应。试验结果表明:1.2%~1.6%复合添加剂调制的CKD220工业齿轮油中,磷酸脂盐的正确选用可以提高齿轮油的抗乳化性能、防锈性能和减少防锈剂用量。硫化烯烃与磷酸脂盐、含氮杂环衍生物多功能添加剂的合理组合,可以提高齿轮油的极压抗磨性能和防锈性能,减少添加剂总加剂量。     

基于LotusNotes的文档ID应用剖析

介绍了文档数据库Lotus Domino／Notes的特点．对其文档处理的核心，即Notes文档的ID构成机制作了系统剖析．并在此基础上分析了如何在文档复制中运用ID的不同组件以及如何运用API程序访问文档ID等。     

EBSP study of the annealing behavior of aluminum deformed by equal channel angular processing

Commercial purity aluminum (99.5%) was fabricated by equal channel angular pressing (ECAP) up to total accumulated strains of approx. 10. The annealing behavior of material deformed to total strains of approx. 1 and 10 was investigated, using heat treatments of 2 h at various temperatures from 100 to 500 °C. The microstructure of the annealed materials was characterized using the electron back-scatter pattern technique. A number of parameters were determined including the distribution and average values of both the boundary spacings and misorientations. For samples deformed to a total strain of 1, annealing resulted in discontinuous recrystallization. For samples deformed to a total strain of 10, annealing resulted in microstructures exhibiting characteristics of both uniform coarsening and, in a number of places, of discontinuous recrystallization. An attempt was made, based on the boundary spacing distributions, to separate these two components. The grain size after annealing was still however small, being just 6.4 μm after 2 h at 300 °C.     

阻尼胶囊的生产工艺研究

通过对胶料配方、工艺规程、模具结构的试验研究，成功地解决了胶囊制造过程中的难点问题。     

Vapor absorption by LiBr aqueous solution in vertical smooth tubes

Heat and mass transfer in a falling film vertical in-tube absorber was studied experimentally with LiBr aqueous solution. The presented results include the effect of solution flow rate, solution subcooling and cooling water temperature on the absorption in a smooth copper tube 16.05 mm I.D. and 400 mm long. The experimental data in the previous report for a 1200-mm-long tube was also re-examined and compared. It was demonstrated by the observation of the flow in the tube that the break down of the liquid film into rivulets leads to deterioration of heat and mass transfer at lower film Reynolds number or in longer tubes. An attempt to evaluate physically acceptable heat and mass transfer coefficients that are defined with estimated temperature and concentration at the vapor–liquid interface was also presented.     

Fatigue crack growth in SiC particulates reinforced Al matrix graded composite

The SiC/Al graded composite was fabricated by powder metallurgy processing and its fatigue crack growth behavior was studied. The volume percentage of SiC particulates was distributed from 5 to 30% layer by layer on the cross section. Since the aluminium was dissolved together, there was no evident interface between the two layers with different volume fraction of SiC particulates. Fatigue crack growth was in direction of from 5 to 30% SiC layers under sinusoidal wave-form. The retardation of fatigue crack growth was found when crack propagated from low volume fraction of SiC to high volume fraction of SiC. The crack deflection and branching between two layers were observed, which decreased crack growth rates. In view of crack tip driving force, the plasticity mismatch between the layers shielded crack tip driving force, i.e. decreased the effective J-integral at the tip of the crack as the plastic zone of the crack tip spread from the weaker material into the stronger material.