Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

珠海台网络硬盘多频道数字播控系统

叙述了以视频服务器为中心构建的网络化多频道自动播出系统的实践、见解和系统的特点。该系统着重考虑了视频服务器选型、系统可靠性、网络化控制及监控、信号共享等问题；同时，实现了多路同时上载、多路边播边上载，以及自动延时播出等功能。     

砂岩酸化中水化硅沉淀的影响因素分析

讨论了砂岩酸化中产生水化硅沉淀的反应机理。使高岭土与1.0%HF和多种配比的HCl HF在不同温度(20-90℃)反应不同时间(10-300分钟),用等离子吸收光谱法(ICP)测定酸液中可溶性硅的浓度(mg/L),取某时段测定值的减小量为该时段水化硅沉淀生成量,讨论了多种因素的影响,得到了如下结果和结论。反应温度越高,则高岭土与HF之间的反应越快,形成水化硅沉淀的时间越短,最终生成的沉淀量越大;在HF中加入HCl(使用土酸体系)、减小土酸中HF质量分数、加大土酸中HCl、HF质量分数比,均可使生成沉淀时间延后,使最终生成沉淀量减少。60℃时300分钟沉淀量,在1.0%HF、5.0%HCl 1.0%HF、9.0%HCl 1.0%HF中分别为482、321、201mg/L。提出了在酸化设计与施工中可以采取的6条简便易行的减少水化硅沉淀量的措施。图4表1参6。     

低温低渗透砂岩油藏窜流大孔道深部封堵技术研究

所用堵剂为高强度的淀粉接枝聚丙烯酰胺交联凝胶SAMG-1,由<6%淀粉、4.5%-5.5%丙烯酰胺、0.003%-0.006%交联剂组成,35℃成胶时间受淀粉和交联剂用量控制,为18-20小时以上,成胶前黏度-100 mPa.s。该堵剂具有长期稳定性,在储层岩心中注入深度15 cm的堵剂,在35℃候凝48小时后及老化90天后,封堵强度分别为0.61和0.59 MPa/cm,封堵率分别为98.6%和98.1%。该堵剂优先进入高渗层,注入0.5 PV并成胶后,2组双填砂管组成的模型低、高渗管渗透率保留率分别为68.4%、0.7%和69.4%、0.0%。吉林扶余油田西一区+15-8.2区块有水井6口,油井13口,含水率达91.5%,注入水最快在5天内到达油井。报道了该区块整体深部调剖封堵窜流通道的情况,详细叙述了+15-9.2井施工中通过注入压力和井底回压控制注入流量,使堵剂陆续进入原生和次生孔道的工艺作业,该井设计注入堵剂92 m3。6口水井整体调剖后,油井产液量差别减小,产油量增加,有效期已超过了9个月,共增油843 t,含水平均下降3.87%。图7表1参8。     

基于ARM微处理器的故障记录系统

给出了在普通数据采集基础上的故障记录系统的设计方案,利用ARM微处理器实现了模拟信号较完整的故障波形记录和开关信号的事件顺序记录(SOE)。对LPC2106ARM系列处理器、ADS7871模/数转换器以及数据通信接口等内容进行了讨论,阐述了系统的工作原理、软件处理方式、系统通信。该设计方案电路简单,特别适用于电力系统。     

GPRS手机入网测试自动化

全球移动通信系统(GSM)广泛的应用于现代通信系统就在于其良好的兼容性,不同的移动设备之间在遵守一定协议规范的条件下可以相互通信;本设计测试的是GSM第11系列GSM11.10,他包括诸多测试项,只对接收机参考灵敏度电平在GSM900与DCS1800两个频段进行测量。给出了传统形式下的手动测试和自动测试平台的比较,并建立了收信机参考灵敏度指标的自动测试平台。     

四级蒸馏在常减压装置扩能改造中的应用

四级蒸馏工艺在镇海炼化第二套常减压装置扩能改造中得以成功应用,为新工艺在常减压装置扩能改造中的推广应用提供了可靠的经验。     

DS/FH通信系统的跳频同步技术研究

同步是DS/FH混合通信系统的关键技术之一。根据跳频系统中对同步的要求,介绍了一种适用于DS/FH混合扩频通信系统的跳频同步方法,采用同步字头和精准时间相结合的方法实现跳频同步。对同步性能进行了分析,结果表明该跳频同步方法同步时间短,捕获概率高。     

一种用于三电平逆变器的SVPWM调制方法研究

本文从二极管箝位型三电平逆变器的基本结构出发，分析其输出状态，推导出六角形空间电压矢量图。然后从一种改进的，可以减小开关损耗，避免高的dv／dt三电平空间矢量PWM调制策略出发，建立了基于Matlab的详细仿真方案，验证了方案的可行性。文章给出了扇区判断的算法流程图，脉冲生成模块的内部结构图，其中的扇区判断的算法和脉冲生成方法对于用DSP实现三电平SVPWM具有重要的参考价值。     

Finite element piezothermoelasticity analysis and the active control of FGM plates with integrated piezoelectric sensors and actuators

 An efficient finite element model is presented for the static and dynamic piezothermoelastic analysis and control of FGM plates under temperature gradient environments using integrated piezoelectric sensor/actuator layers. The properties of an FGM plate are functionally graded in the thickness direction according to a volume fraction power law distribution. A constant displacement-cum-velocity feedback control algorithm that couples the direct and inverse piezoelectric effects is applied to provide active feedback control of the integrated FGM plate in a closed loop system. Numerical results for the static and dynamic control are presented for the FGM plate, which consists of zirconia and aluminum. The effects of the constituent volume fractions and the influence of feedback control gain on the static and dynamic responses of the FGM plates are examined. Received: 13 March 2002 / Accepted: 5 March 2003 The work described in this paper was supported by a grant awarded by the Research Grants Council of the Hong Kong Special Administrative Region, China (Project No. CityU 1024/01E).