Numerical analysis of galvanic corrosion of Zn/Fe interface beneath a thin electrolyte

A numerical analysis of galvanic corrosion of a Zn/Fe interface beneath a thin layer electrolyte is presented. Specifically, a circular defect, where the zinc coating has been removed, is considered. It is assumed that both oxygen reduction and iron oxidation can occur on the Fe surface, while only zinc oxidation occurs on the Zn surface. The importance of electrolyte thickness and conductivity and defect radius is considered. It is assumed that the iron and zinc oxidation rates are described by a Tafel relationship. If the kinetic parameters of the oxidation reactions are known, the cathodic protection of Fe is a function of a Wagner number, the ratio of the electrolyte thickness to the defect radius, and the ratio of the radius of the defect to the outer radius of the zinc layer.     

载体预处理对Pd/C催化剂催化性能的影响

研究了活性炭硝酸表面改性对以其为载体制备的负载钯催化剂性能的影响。利用表面官能团滴定、N₂物理吸附和扫描电镜对催化剂进行表征，以邻硝基氯苯催化加氢制备2，2'-二氯氢化偶氮苯反应为模型反应对催化剂的性能进行评价。结果表明，经过不同浓度的HNO₃处理，活性炭孔结构性能变化不大，但是活性炭表面酸性含氧基团的浓度有了较大程度的增长，为Pd金属粒子的沉积提供了大量的吸附位，提高了Pd金属的分散度，从而制得高活性的Pd/C催化剂。通过30%HNO₃ 60 ℃水浴中回流4 h处理的活性炭可以达到最佳效果，所制得催化剂的活性是以未经硝酸处理过的活性炭载体制备的催化剂活性的2.3倍。     

Unique Dielectric Behavior of 0.6Pb(Ni1/2W1/2)O3·0.4PbTiO3 Derived from Mechanical Activation

0.6Pb(Ni_1/2W_1/2)O₃·0.4PbTiO₃(0.6PNW·0.4PT) of complex perovskite structure is successfully synthesized by mechanical activation of mixed oxide composition, followed by sintering at 950°C. It exhibits a considerably stable temperature dependence of dielectric constant over the wide temperature range of −120° to 20°C, although there occurs a dielectric peak at around 74°C. Raman spectroscopic studies show the coexistence of tetragonal and pseudocubic perovskite phases on sintering at 950°C, which are attributed to the inhomogeneous distribution of PbTiO₃ arising from mechanical activation. The dielectric behavior can be fine tuned by thermal annealing at 750°C, leading to phase redistribution in PNW-PT.     

Synthesis of Thermally Stable χ-Alumina by Thermal Decomposition of Aluminum Isopropoxide in Toluene

Thermal decomposition of aluminum isopropoxide in toluene at 315°C resulted in χ-alumina that had high thermal stability, whereas the reaction at lower temperatures resulted in formation of an amorphous product. The χ-alumina thus obtained directly transformed to α-alumina at ∼1150°C, bypassing the other transition alumina phases, whereas the amorphous product transformed to γ-alumina and then to θ-alumina before final transformation to α-alumina. When the χ-alumina, solvothermally synthesized at 315°C, was recovered by the removal of the solvent at the reaction temperature, thermal stability of the product was improved further. This procedure is convenient because it avoids bothersome work-up processes that yield large-surface-area and large-pore-volume alumina.     

Crystallographic Texture Development in Bismuth Sodium Titanate Prepared by Reactive-Templated Grain Growth Method

Bi_0.5Na_0.5TiO₃ (BNT) and 0.94Bi_0.5Na_0.5TiO₃·0.06BaTiO₃ (BNT–BT) bulk ceramics with extensive 〈100〉 texture were prepared by the reactive-templated grain growth method, using platelike Bi₄Ti₃O₁₂ (BIT) particles as templates for BNT. Calcined compacts were composed of matrix grains with random orientation and 〈100〉-oriented grains transformed from aligned BIT particles, and the texture developed by the growth of oriented grains during sintering. Ceramics with extensive texture were obtained by using the starting mixture containing the maximum concentration of platelike BIT to form the maximum volume fraction of oriented grains.     

Top-Down方法在成型模具设计中的应用

介绍模具Top—Down设计的基本思想、设计流程及其主要特点，并基于Pro/Engineer软件平台，以一鞋楦模具为设计对象，例示出模具Top—Down设计方法的主要设计过程。采用先进的Top-Down模具设计方法可以帮助设计者提高设计速度，避免一般设计中容易发生的错误，降低设计制造成本，加快交货期限。     

A/O结合循环式活性污泥法处理海产品加工废水

针对海产品加工废水氨氮含量较高的特点。舟山兴业有限公司的污水处理工程采用两段A/O结合循环式活性污泥法工艺，工程验收合格后运行一年多来，排放废水的各项污染指标均达到国家《污水综合排放标准》（GB8978-1996）的二级标准，处理系统具有很好的抗冲击能力和脱氮效果。     

GC/MS法建立烟用香精指纹图谱研究

采用超声辅助液液萃取法(ULLE)对8个不同批次的烟用HMT香精成分进行提取,用GC/MS对其进行定性定量分析,建立了该香精的GC/MS指纹图谱的研究方法,目的在于为烟用香精质量控制提供一种方便、快捷、可靠的分析手段。结果表明:ULLE方法具有操作简便、快速、节能、萃取效率高、重现性好等特点,适合于烟用香精成分的提取。8个批次的HMT香精的指纹图谱稳定性好,相似度高,具有很强的特征性和唯一性。通过该香精指纹图谱的建立,对日后进厂的HMT香精进行质量控制提供了依据。     

磷钨钼杂多酸掺杂聚苯胺催化合成丁醛乙二醇缩醛

报道了以磷钨钼杂多酸掺杂聚苯胺为催化剂,通过丁醛和乙二醇反应合成了丁醛乙二醇缩醛。系统考察了醛醇物质的量比、催化剂用量以及反应时间诸因素对产品收率的影响。确定适宜的工艺条件为n(丁醛)∶n(乙二醇)=1∶1.5,催化剂的质量为反应物料总质量的0.8%,反应时间1.0 h。在此反应条件下,丁醛乙二醇缩醛的收率可达71.1%。     

Sintering of Pt/Al2O3 reforming catalysts: EXAFS study of the behavior of metal particles under oxidizing atmosphere

The effect of an oxidative atmosphere (300 °C) is studied on fresh and sintered unchlorinated naphtha reforming catalysts containing 0.6–1% Pt. The TPR profiles show that only one species is formed using our experimental conditions, regardless of the mean crystallite size of the metal particles. The structural information supplied by EXAFS compared with cuboctahedral particle modeling, implies that such species is a surface platinum oxide, the structure of which is close to that of PtO₂, but largely distorted. This is true whether the catalyst is sintered or not.