WTG420铁路罐车用钢的组织结构和力学性能分析

分析了ＷＴＧ４２０铁路罐车用钢的组织结构和力学性能。提出了冶炼与轧制的技术关键，其一，添加稀土元素改善钢中夹杂物；其二，采用控轧控冷使铁素体晶粒细化。     

Microscopic fatigue processes in a plain-weave glass-fibre composite

This paper focuses on the microscopic damage and progressive failure of a composite reinforced by plain-weave glass cloth under tensile fatigue loading. The fatigue process was divided into three stages like that of multi-directional laminates. It was found that the internal damage at each stage (matrix cracks, debonds in the weft, successive debonds in the warp and ‘metadelaminations’ between warps and wefts) occurred near the cross-over point of the fabric. The modulus decay mechanism was explained by considering the progression of this internal damage. From the end of the first stage to the beginning of the middle stage, a characteristic damage state (CDS) (called a ‘meta-CDS’) was observed. It was found that woven composites have a unit area of damage accumulation (called a ‘unit cell’) and the damage of each unit cell and its distribution control the total fatigue damage of the material.     

Thermodynamic Analysis of Various Dehumidifying Dryers for Wood

Typical methods of dehumidification of air circulating in the dehumidifying driers (indirect and direct cooler and partial exchange of the air) were analysed. Energy aspect of cooler operation was evaluated. The method for minimization of unit thermal energy consumption in a dehumidifying drier by the optimal selection of the cooler point was also given. Methods of the heat recovery of heat conveyed in a cooler lending to save energy (heat regeneration. expansion and compression of the air, a dehumidifier) were analysed. It was indicated that introduction of dehumidifiers into contemporary wood driers caused significant improvement of energy aspects of their operation     

Reduction of Stibnite at Moderate Temperature

Reduction of stibnite with hydrogen in the presence of calcium oxide has been experimentally inves-tigated at moderate temperature. The results reveal that the effluent generated in the reduction pro-cess contains much less air-polluting substance H_2S, and that the reaction activation energy is63. 3 kJ/mol. The form of antimony changes considerably when the reaction temperature varies.     

Performance of absorption refrigeration cycle at maximum cooling rate

The influence of irreversibility of finite-rate heat transfer on the performance of an absorption refrigerator is investigated using an endoreversible cycle model with continuous flow. The cooling rate is adopted as an objective function for refrigerator optimization. The maximum cooling rate and the corresponding coefficient of performance are derived. The optimal performance with respect to heat transfer areas of the refrigerator is analysed. In addition, certain significant conclusions are reached.     

The performance of a direct-sequence spread-spectrum acquisition system using a linear prediction filter for narrowband interference suppression

The coarse acquisition performance of a direct sequence spread-spectrum receiver is analyzed when a linear prediction filter is used for narrowband interference suppression. We show that once an appropriate matching strategy is identified, the linear prediction filter can provide favorable performance when narrowband interference is present over a considerable range of both interference power and bandwidth. In addition, the presence of the filter dramatically improves the performance over the case where there is no filter, except when the interference bandwidth and the power are both small (i.e., when the processing gain provides sufficient interference immunity without the filter). If long spreading sequences are used with moderately sized observation windows, the acquisition performance can be severely degraded when a parallel acquisition scheme is used due to the linear predication filter. We show, however, that a slower serial receiver will provide reliable performance.This work was supported in part by the Office of Naval Research under contract ONR N00014-91-J-1234, the Army Research Office under contract ARO DAAL03-91-0071, and the NSF Center for Ultra-High Speed Circuits and Systems (ICAS).     

28Cr2Mo1VA钢变速冷却转变动力学研究

用膨胀法对28Cr2Mo1VA钢测定了变速冷却过冷奥氏体转变动力学曲线,结果表明,先慢冷后快冷,珠光体、贝氏体转变滞后;反之,转变超前。并提出用图解计算法求转变点,结果与实验相符合。     

含氮化合物废气选择性催化氧化技术研究进展

通过对当前含氮化合物废气治理技术的对比分析,总结选择性催化氧化的相关技术优势。根据对含氮化合物的种类及来源分析,介绍氨气、腈类、胺类及其他含氮化合物的催化净化技术。重点总结催化剂的种类、研发进展和在实际使用中可能遇到的问题,同时展望含氮化合物废气选择性催化氧化技术的研发方向。     

三维定量储层地质模型与参数动态预测方法

提出了三维定量储层地质模型及其参数动态预测方法，用该方法可预测储层开采状态，水淹区及剩余油区分布和各剩余油区的可采储量，三维定量储层地质模型的预测图件可为合理开采提供依据。     

The effect of pre-wetting on dynamic contact angles

A roll-coating experimental system is used to study the effect of pre-wetting on dynamic contact angles, the interfacial displacement depth, and the associated phenomenon of air entrainment. The system consists of a roll, which is horizontally rotating in a liquid pool. The dynamic contact angle is recorded by a macrophotography system. The test liquids are glycerol solutions with viscosities in the range 104 < μ < 748 mPa · s. The value of (μV/ρg)^0.5 is taken as the characteristic length to be used in the dimensionless relationships which correlate experimental measurements. The effect of base layer entry angle into the liquid pool on the dynamic contact angles and other flow parameters is studied. Comparison is made with measurements in dry tape-coating and other pre-wet roll–coating systems.