冷轧带肋钢筋直径与拉丝机卷筒直径的匹配

采用被动式工艺生产冷轧带肋钢筋须经过减径、成型两台轧机连续轧制．要求钢材的秒流量相等，否则将造成断线停产或线材在拉丝机卷筒上打滑，致使卷筒严重磨损．用双层卷筒拉丝机提供动力生产冷轧带肋钢筋时，线材直径与卷筒直径的匹配是在一个小的调整范围，通过轧机拉力控制在一定范围变化，可保证成品尺寸符合公差要求而不产生打滑，从而避免了卷筒严重磨损．     

基于Multisim8的压控振荡电路仿真分析

介绍了Multisim8的仿真功能的特点，并通过实例说明了用Multisim8进行仿真分析的具体方法，简单介绍了如何设置参数和进行仿真操作。     

Note on ‘Construction of Double Sampling s‐Control Charts for Agile Manufacturing’

He and Grigoryan (Quality and Reliability Engineering International 2002; 18 :343–355) formulated the design of a double‐sampling (DS) s control chart as an optimization problem and solved it with a genetic algorithm. They concluded that the DS s control charts can be a more economically preferable alternative in detecting small shifts than traditional s control charts. We explain that, since they only considered the average sample size when the process is in control, their conclusion is questionable. Copyright © 2006 John Wiley & Sons, Ltd.     

连轧机用人字轮齿轴断裂失效分析

用宏观断口分析、化学检验、力学性能测定、低倍检查、金相组织及夹杂物评定鉴别、受力分析及强度寿命定量估算的方法，对人字轮被动齿轴端断裂失效原因进行分析，并提出改进措施。     

Electrochemical Aspects of Electroosmotic Dewatering of Clay Suspensions

An attempt is made to elucidate the electrochemical aspects of the electroosmotic dewatering (EOD) of clays as reported in some recent work, especially that on interrupted DC power electroosmotic dewatering published by Rabie, Mujumdar and Weber (2). These authors showed that the dewatering by EOD stops after the DC power has been on for several minutes or hours; on interruption of their power and on short-circuiting of the electrodes, conditions can be created again for some further dewatering by DC power EOD. This discovery, of Rabie et al. is interpreted as a fuel cell effect and it is shown that it affords clues to several other electrochemical strategies for the possible enhancement of the efficiency of the EOD by DC power.

Further, the open circuit potentials observed by Rabie et al. (2) on the interruption of DC power are given an electrochemical interpretation which leads to quantitative estimates in agreement with the experimental values.     

高可靠镀Ni／Au工艺及其在微波PTFE电路上的应用

介绍了高可靠电镀Ｎｉ／Ａｕ工艺在ＰＴＦＥ微波印制电路上的应用，并分析了氨基磺酸盐镀软镍和亚硫酸盐镀软金工艺的影响因素及提高Ｎｉ／Ａｕ镀层之间附着力的措施。通过实验及应用证明了与直接镀金工艺相比，在软基材ＰＴＦＥ敷铜箔板上镀Ｎｉ／Ａｕ工艺能大大提高微波电路的可焊性，高温稳定性和长期可靠性，并且用其所制作的微波器件的高频性能也优于直接镀金工业。     

STI process steps for sub-quarter micron CMOS

This paper presents Shallow Trench Isolation (STI) process steps for sub-1/4 μ CMOS technologies. Dummy active areas, vertical trench sidewalls, excellent gap filling, counter mask etch step and CMP end point detection, have been used for a 0.18 μm CMOS technology. Electrical results obtained with a 5.5 nm gate oxide thickness show good isolation down to 0.3 μm spacing. Good transistor performances have been demonstrated.     

CMOS电路中抗Latch-up的保护环结构研究

闩锁是CMOS集成电路中的一种寄生效应,这种PNPN结构一旦被触发,从电源到地会产生大电流,导致整个芯片的失效。针对芯片在实际测试中发现的闩锁问题,介绍了闩锁的测试方法,并且利用软件Tsuprem4和Medici模拟整个失效过程,在对2类保护环(多子环/少子环)作用的分析,以及各种保护结构的模拟基础之上,通过对比触发电压和电流,得到一种最优的抗Latch up版图设计方法,通过进一步的流片、测试,解决了芯片中的闩锁失效问题,验证了这种结构的有效性。     

同杆并架双回线基于电流突变量的综合选相

相电流差突变量选相元件在单回线故障中具有良好的选相性能，但在同杆双回线跨线故障中可能误选相。利用六序故障分量的分析方法，分析了相电流突变量在同杆双回线跨线故障中的幅值和相位特征，给出了其相位比相方程。在此基础上，提出了一种运用测量阻抗和方向元件相结合的综合选相方法，并给出了选相流程图。仿真结果表明，在双回线简单故障和跨线故障时，基于单回线单端电气量的同杆并架双回线综合选相方法具有较理想的选相性能。     

岩盐钻井水溶双井连通开采工艺的研究与推广

文章就全国井矿盐采区多年的开采工艺技术，进行了系统的研究与总结，并提出了岩盐钻井水溶开采双井连通的各种开采工艺及其关键技术，具有很强的适用性和推广价值。