双相位共轭镜的工作条件参数分析

本文讨论了纯扩散机制的光折变晶体用作单作用区的双相位共轭镜（ＤＰＣＭ）时的阈值耦合强度和允许的输入光强比范围，并与双作用区的情况进行比较后，给出了在输入光强比远离１的条件下，双相位共轭镜的正常工作的条件参数。     

A low power and small area all digital delay-locked loop based on ring oscillator architecture

A 133-500 MHz,5.2 mW @500 MHz,0.021 mm2 all digital delay-locked loop(ADDLL)is presented.The power and area reduction of the proposed ADDLL are achieved by implementing a high frequency ring oscillator(ROSC)to count the reference clocks such that the one-clock cycle delay chain and the phase detector in a conventional Master block are no longer needed.The proposed ADDLL has better immunity to PVT(process,voltage,and temperature)than most conventional DLLs,which do not update the control word signals after the locking process,since the control signals for slave delay line are updated in every 256 reference cycles.Fabricated in 0.13 um CMOS process,the measured RMS jitter is 10.83 ps at 500 MHz while the RMS jitter of the input signal is 9.97 ps.     

卧螺离心机变频调速PLC控制系统设计

针对传统的卧螺离心机控制系统存在稳定性差、工作效率低的问题,设计了一种卧螺离心机变频调速PLC控制系统;详细介绍了该系统中共直流母线变频调速系统、副电机随动方案及负载率调整方法、PLC控制系统、组态界面的设计。实际应用表明,该系统运行稳定,提高了离心机的性能。     

Blind estimation of the PN sequence in lower SNR DS-SS signals with residual carrier

This paper presents a method of singular value decomposition (SVD) plus digital phase lock loop (DPLL) to solve the difficult problem of blind pseudo-noise (PN) sequence estimation in low signal to noise ratios (SNR) direct sequence spread spectrum (DS-SS, DS) signals with residual carrier. Of course, the method needs to know the parameters of DS signal, such as the period and code rate of PN sequence. Firstly, the received signal is sampled and divided into non-overlapping signal vectors according to a temporal window, whose duration is two periods of PN sequence. Then, an autocorrelation matrix is computed and accumulated by the signal vectors one by one. The PN sequence with residual carrier can be estimated by the principal eigenvector of this autocorrelation matrix. Furthermore, a DPLL is used to deal with the estimated PN sequence with residual carrier, it estimates and tracks the residual carrier, removes the residual carrier in the end. Theory analysis and computer simulation results show that this method can effectively realize the PN sequence estimation from the input DS signals with residual carrier in lower SNR.     

基于环探头测量含运动导体的瞬态电流波形

电流除了用罗果夫斯基线圈进行测量外,还可通过环探头测量电流产生的磁场来计算得到。直线电机除了位置固定的母线导体外,还有沿母线运动的电枢;母线回路注入脉冲电流后,电枢会被加速而运动。简化母线和电枢为线电流模型,在长线模型基础上,通过环探头测量得到的磁场计算出近似电流波形。因为探头所测磁场主要由其附近电流所贡献,所以合理配置电枢起始位置与探头位置后,电枢运动对电流测量的影响很小。在瞬态电流上升沿、平台区和下降沿的不同阶段,利用实验折算的系数,可得到时域瞬态电流波形,其测量结果与用罗果夫斯基线圈测量波形一致。     

热卷箱是提高热连轧线竞争能力的最佳选择

介绍了热卷箱技术的发展及在我国的应用情况。结合“双工位无芯卷取”热卷箱技术在宝钢集团梅山钢铁公司1422mm热轧厂的成功应用，重点介绍了该技术的特点及在解决热轧板带中节能减排、减少氧化铁皮、避免甩尾、稳定精轧轧制及开发高附加值产品等方面的优势；认为其是提高热轧板厂竞争力的最佳选择。     

Photocatalytic syngas synthesis from CO2 and H2O using ultrafine CeO2-decorated layered double hydroxide nanosheets under visible-light up to 600 nm

The rational design of photocatalyst that can effectively reduce CO₂ under visible light(l>400 nm),and simultaneously precise control of the products syngas(CO/H2)ratio is highly desirable for the Fischer-Tropsch reaction.In this work,we synthesized a series of CeO₂-decorated layered double hydroxides(LDHs,Ce-x)samples for photocatalytic CO₂ reduction.It was found that the selectivity and productivity of CO and H₂ from photoreduction of CO₂ in conjunction with Ru-complex as photosensitizer performed an obvious“volcano-like”trend,with the highest point at Ce-0.15 and the CO/H₂ ratio can be widely tunable from 1/7.7 to 1/1.3.Furthermore,compared with LDH,Ce-0.15 also drove photocatalytic CO₂ to syngas under 600 nm irradiation.It implied that an optimum amount of CeO₂ modifying LDH promoted the photoreduction of CO₂ to syngas.This report gives the way to fully utilize the rare earth elements and provides a promising route to enhance the photo-response ability and charge injection efficiency of LDH-based photocatalysts in the synthesis of syngas with a tunable ratio under visible light irradiation.     

复吹转炉“留渣 双渣”脱磷工艺试验

摘要：在国内某转炉钢厂采用“留渣 双渣”工艺技术进行脱磷工艺试验。结果表明：随着转炉前期脱磷率不断升高,终点脱磷率不断提高。铁水硅含量对前期脱磷率的影响最大。根据铁水成分,在冶炼前期适当降低供氧强度、降低气固氧比、加入适量石灰及烧结矿,均有利于前期脱磷率的提高。在一倒时每吨钢液加入4~8kg石灰,不影响出钢温度,可提高一倒-终点阶段脱磷率,同时可提高终点脱磷率。从终点的控制效果可知,终点炉渣碱度应保持不小于3.0,炉渣中FeO质量分数在16%~20%,并适当降低终点出钢温度在1610~1630℃,有利于终点脱磷率的提高。通过加强熔池搅拌,促进钢渣反应趋于平衡,有利于终点磷分配比提高,从而可进一步提高终点脱磷率。     

Characterization of angular dependence of macroscopic magnetic properties in ASTM 36 steel using magnetic Barkhausen noise

Angular-dependent magnetic Barkhausen noise measurements were performed on ASTM 36 steel samples for various values of applied uniaxial stress. The maximum differential permeability and the coercive field are obtained from this Barkhausen signals. The angular dependence of these macroscopic magnetic properties is studied. The tension for which the magneto-elastic energy balances the anisotropic energy is estimated. The results are discussed based on the domain wall theory.     

双滑移取向Cu单晶的循环形变行为──Ⅱ．滑移带和形变带SCIEI

用光学显微镜和扫描电镜研究了双滑移取向（［０３４］，［１１７］）Ｃｕ单晶循环饱和后的表面形貌，塑性分切应变幅（γｐｌ）低于１０^（－３）时，［０３４］晶体表面上要为主滑移系的驻留滑移带（ＰＳＢｓ）占据，次滑移只在边缘区域启动，其ＰＳＢｓ细窄（＜１μｍ），体积百分数在１％以下．γｐｌ＞１０^（－３）时，次滑移开始在试样的中部启动，同时，表面出现二种贯穿晶体的宏观形变带（ＤＢＩ，ＤＢＩＩ），滑移带在形变带内集中．［１１７］晶体在γｐｌ＝４．４×１０^（－４）时，双滑移现象已十分明显．γｐｌ＞１０^（－３）时，表面也形成与前者相似的形变带．ＤＢＩ的惯习面与主滑移面平行（［０３４］晶体）或接近（［１１７］晶体），ＤＢＩＩ的惯习面则与前者垂直，文章讨论了形变带形成的可能原因．