一种新型针刺延期药的研制及其应用

本文介绍了一种新型的针刺延期药的配方设计和制备工艺，这种低猛度高热量的针刺延期药具有较高的发火感度，可满足一定的延期时间和相容性要求。文中还介绍了它在几种小型针刺延期雷管中的应用。     

含RDX的硝胺丁羟推进剂能量特性研究

采用最小自由能平衡流法对RDX/AP/Al/HTPB推进剂能量特性进行了理论计算。通过BSF165mm和BSF315mm发动机点火试验,研究了RDX含量、燃烧室压强对RDX/AP/Al/HTPB推进剂能量特性的影响规律。根据理论计算和发动机试验结果,对配方进行了优化设计,与某型号760mm全尺寸发动机的实测结果对比,其实测比冲高达2428.1N·s·kg-1(pc=6.86MPa),验证了RDX的加入对RDX/AP/Al/HTPB推进剂比冲有较突出贡献。     

Energy absorption in splitting square metal tubes

This paper presents an investigation into the energy absorbing behaviour of axially splitting square metal tubes. Tubes 50 mm square with a variable thickness were pushed slowly against rigid pyramid shaped dies, which had various semi-angles. By pre-cutting 5 mm long slits at the four corners, the tube splits along the corners and curls outward with a certain radius at a constant force. In this energy dissipating system, there are three components: tearing energy, plastic deformation energy and frictional energy. Theoretical analysis of the three energy components is presented. Curl radius is also studied in detail. Good agreement between experiments and theory is obtained. The results show that tubes which both split and curl may be used as efficient, long stroke energy absorbing devices.     

Rolling contact fatigue behavior of sintered and hardened steels

Powder-metal-processed bearings and gears are finding increasing application because of their economical and technical advantages. The residual pores from the sintering operatives act as lubricant pockets and dampen sound and vibration. However, porosity also decreases the mechanical strength and reduces the life of components fabricated by powder processing relative to similar wrought components. The rolling contact fatigue behavior of sintered and heat treated steel rollers was investigated using a fatigue test machine designed and fabricated for that purpose. The powder-metal-processed and the wrought steel rollers that were tested had similar composition and hardness and were mated against wrought steel rollers of high hardness. The contact stress versus number of cycles to failure data showed that the wrought steel had a very high endurance limit under rolling contact fatigue compared to the sintered steels investigated. Rolling contact fatigue behavior was found to depend on the porosity present in the material. Large surface peeling failures and pitting type fatigue failures were observed in the sintered and hardened steels, while only pitting type failures were observed in the wrought steels     

《关于加强嫩江松花江近期防洪建设的若干意见》论证概要

水利部《关于加强嫩江松花江近期防洪建设的若干意见》近期已由国务院办公厅批转有关省、自治区和国务院有关部门执行。本文简单介绍了《关于加强嫩江松花江近期防洪建设的若干意见》编制过程中对设计洪水、防洪标准、工程布局和非工程措施的论证情况和主要结论。     

通信局(站)的接地与防雷

论述了分散接地与联合接地系统在防雷作用上的差异，归纳出通信局（站）在防雷与接地方面的若干原则。     

Systematic analysis of neutron yields from thick targets bombarded by heavy ions and protons with moving source model

A simple phenomenological analysis using the moving source model has been performed on the neutron energy spectra produced by bombarding thick targets with high energy heavy ions which have been systematically measured at the Heavy-Ion Medical Accelerator (HIMAC) facility (located in Chiba, Japan) of the National Institute of Radiological Sciences (NIRS). For the bombardment of both heavy ions and protons in the energy region of 100–500 MeV per nucleon, the moving source model incorporating the knock-on process could be generally successful in reproducing the measured neutron spectra within a factor of two margin of accuracy. This phenomenological analytical equation is expressed having several parameters as functions of atomic number Z_p, mass number A_p, energy per nucleon E_p for projectile, and atomic number Z_T, mass number A_T for target. By inputting these basic data for projectile and target into this equation we can easily estimate the secondary neutron energy spectra at an emission angle of 0–90° for bombardment with heavy ions and protons in the aforementioned energy region. This method will be quite useful to estimate the neutron source term in the neutron shielding design of high energy proton and heavy ion accelerators.     

风机盘管在空调工程中的应用及分析

根据风机盘管的特性，分析了设备运行状况和能量调节方法等方面的有关问题，指出了风机盘管采用变风量的方法调节能量所存在的弊端，同时还分析了在空调设计中，如何充分运用这些特点来合理选型，并对产品开发方面提出了建议。     

浅谈中承式钢管拱肋单拱桥的施工方法

右江平圩大桥钢管拱肋的制作、拼装、吊装、混凝土灌注的施工方法及注意事项 ,事故原因分析及处理。     

SP预应力空心板在居住建筑中的应用和发展

分析现浇板和传统预制板的特点和弱点，提出发展SP板和SP叠合板是住宅实现大开间、灵活隔断的有效途径之一，也是建筑施工实现现代化的重要内容之一。