Evaluation of influence of external magnetic disturbance on superconducting magnet taking conservation of linkage flux into account

External magnetic disturbance influences the quality of the image obtained with a magnetic resonance imaging (MRI) system because it causes magnetic resonance frequency drift. When a superconducting magnet in persistent current mode operation is exposed to external magnetic disturbance coil current varies to keep linkage flux constant. Conventional analysis is usually formulated with constant current and does not provide correct evaluation of drift of magnetic field in the magnet. This paper proposes a method of numerical analysis of magnetic field considering conservation of linkage flux in a superconducting magnet under a persistent current mode operation. This method is applied to evaluate drift of the magnetic field in a superconducting magnet for magnetic resonance imaging due to external magnetic disturbance. Analysis results show good agreement with the experimental results.     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

沼气汽车加气站的探讨

分析了适合于汽车加气用沼气的品质，就沼气汽车加气站的流程、设备选型等进行了论述。     

Effect of water inlet velocity on thermal stratification in a mantled hot water storage tank

Thermal stratification in a mantled hot water storage tank is analysed numerically for different water inlet velocities. The aim is to obtain higher thermal stratification and supply hot water for usage as long as possible. Twelve different water inlet velocities to the hot water storage tank are considered. The numerical method is validated by comparing its results against experimental and numerical results from the literature. It turned out that the results obtained from the numerical analysis have shown very good agreements with the results from previous works. As a result, the water temperature in the tank increases with the increase of the water inlet velocities to the mantle but this increment is not proportional. After a period of operation of 7.2 h, which corresponds to the average sunshine duration in Turkey, temperature increments of 6.5 and 35 K have been estimated for the hot water inlet velocities of 0.01 and 0.3 m s^?1, respectively, at a radial distance of 0.1 m and a height of 1 m inside the storage tank. Copyright © 2005 John Wiley & Sons, Ltd.     

Effect of pretreatments and freezing rate on the firmness of potato tissue after a freeze–thaw cycle

The texture of potato tissue after a freeze–thaw process using different freezing rates and different pretreatments was analysed, in order to select the best strategy for optimum preservation of the textural characteristics of pre‐frozen potato. Ten blanching conditions were tested and a two‐step blanching process with calcium chloride (0.07 g mL^?1) proved the most effective in protecting the tissue after a freeze–thaw process (maximum load force around 10–55% of the raw tissue, depending on potato batch, for air‐blast freezing and 20–60% for immersion freezing). Vacuum impregnation at 100 and 400 mbar, even when followed by different pre‐drying treatments to remove excess water, was very detrimental to resistance to a freeze–thaw process (maximum load force below 10% of the raw tissue for air‐blast freezing and below 20% for immersion freezing). Microstructure analysis confirmed better tissue integrity retention with ethyleneglycol immersion freezing instead of air‐freezing. Differences were found between batches with a 6‐month difference in storage time, indicating that the fresher batch was more suitable for freezing.     

Use of ultrafiltration for preparing improved tomato pulp

The characteristics of high-quality tomato pulp (commercial def.: crushed or diced tomatoes with about 30% tomato juice as packing medium) canned with tomato juice pulp enriched by ultrafiltration as packing medium were compared with those covered with conventional vacuum-concentrated juice.
Both hot- and cold-break products were prepared and those containing 20% serum-reduced packing juice proved to be the best, showing no signs of syneresis on storage and with improvements in sensory properties, colour and non-enzymatic browning; some volatile components were reduced.     

Control of polymerization processes of 10,12-pentacosadiynoic acid LB films

Studies have been carried out on KrF excimer laser light (EX), X-ray or electron beam (EB) induced polymerization of 10,12-pentacosadiynoic acid (PDA) Langmuir-Blodgett (LB) films in relation to molecular density or molecular arrangement of the films using X-ray diffraction analysis, infrared (IR) spectroscopy and Raman spectroscopy. The molecular arrangement or density of the PDA LB films was controlled by subphase conditions when the films were built up, such as pH, temperature of a subphase or salt concentration in the subphase. Polymerization sensitivity of the PDA LB film was affected by the arrangement or molecular density. On low density (A type) films the polymerization occurred by irradiation with EX, X-ray or EB, but on high density (B type) films the polymerization occurred only when the irradiation was carried out by high energy beams such as X-ray or EB. Decomposition of polymerized films was observed further by excessive irradiation of EX or X-ray, but not on the B type films. It was revealed by X-ray diffraction analysis that in the A type film, the PDA molecules bent to a larger extent than those in the B type film and the polymerization proceeded topochemically, that is, the thickness decreased little after EB irradiation in a helium atmosphere. On the other hand, in the B type film, the thickness decreased by about 10% as a result of EB irradiation. By IR reflection-absorption (RA) and Raman measurements, it was confirmed that conjugated diacetylenic bonds disappeared and conjugated double and new conjugated triple bonds appeared after high energy beam irradiations. These results support the supposition that 1,4-polymerization, i.e. polydiacetylene type polymerization, occurs easily in the A type film and 1,2- or 3,4-polymerization, i.e. polyacetylene type polymerization, occurs in the B type film, and that the polymerized A type film was decomposed at the polydiacetylenic bond when the irradiation continued further. It was also shown that the polyacetylene type polymer was obtained only when the B type film was irradiated with the high energy beam.     

High‐Tech‐Cellulose‐Funktionspolymere nach dem ALCERU®‐Verfahren

Functional High‐Tech‐Cellulose materials by the ALCERU® process Cellulose is one of the eldest materials of mankind. While the use of cellulose in former times was focused on application as a more construction or as a more textile material at present time the application profile turns to a more functional material using the ALCERU® process. Shaping of pure cellulose dissolution in NMMNO permits the manufacturing of materials for upholstery, filtration or biodegradable film strips having an uniform cross section. Fibreds, which can be applied in several packaging materials, are available using different techniques for regeneration cellulose. A great field of innovative functional cellulose materials is opened up by addition of several functional additives to cellulose dissolution. In this way piezo‐electrical conductive cellulose fibres (PZT) or high‐temperature filtration membranes are to be generated if one adds special types of ceramic powders. Above all PZT green fibres are applied in more recent uses as sensors or actuators. Electrically conductive cellulose fibres or filaments, which can be also used in the textile chain, can be prepared adding conductive carbon black to a cellulose dope on the same way, too. Cellulose material having adapted conductivity to different application is available by adding an exact defined amount of carbon black to cellulose dissolution. Finally cellulose beads can be manufactured by means of varied shaping technique. The beads are showing variable particle sizes and narrow pore size distribution. These properties open up very interesting application in the field of human blood purification or chromatography.     

Accidents,often the result of an ‘uncontrolled business process’—a study in the (Dutch) chemical industry

Often companies in the (petro‐) chemical industry claim that all possible countermeasures against potential accidents have been taken and therefore accidents are unforeseeable. In this paper we question this statement by analysing the pre‐warning signals (precursors) preceding a number of industrial accidents. 17 accidents that occurred in the (petro‐) chemical industry have been investigated by exploring FACTS, an accident database containing information about industrial accidents worldwide. This paper will demonstrate that the existence of precursor information could have been used to foresee and even prevent these accidents if a proper control action had been initiated. The accidents are analysed further, according to a control model, which was adapted from that of C. Argyris. It demonstrates the ineffectiveness of several elements of business process control loops and that the so‐called ‘double‐loop learning’ cycle is more important than the ‘single‐loop learning’ cycle if one considers safety improvement. Copyright © 2003 John Wiley & Sons, Ltd.     

An economic and environmental assessment of biomass utilization in lignite‐fired power plants of Greece

The environmental and socio‐economic impacts of biomass utilization by co‐firing with brown coal in an existing thermoelectric unit in Greece or through its pure combustion in a new plant were studied and evaluated in this work. The 125 MW_e lignite‐fired power plant in Ptolemais Power Station (Western Macedonia) was used as reference system. The environmental benefits of the alternative biomass exploitation options were quantified based on the life cycle assessment methodology, as established by SETAC, while the BIOSEM technique was used to carry out socio‐economic calculations. The obtained results showed clear environmental benefits of both biomass utilization alternatives in comparison with the reference system. In addition, co‐firing biomass with lignite in an existing unit outperforms the combustion of biomass exclusively in a new plant, since it exhibits a better environmental performance and it is a low risk investment with immediate benefits. A biomass combustion unit requires a considerably higher capital investment and its benefits are more evident in the long run. Copyright © 2005 John Wiley & Sons, Ltd.