Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

Nitric oxide reduction and carbon monoxide oxidation over carbon-supported copper-chromium catalysts

Carbon supported copper-chromium catalysts are shown to be very active for both the reduction of nitric oxide with carbon monoxide and the oxidation of carbon monoxide with oxygen. Mixed copper-chromium oxide active phases have good activity in the simultaneous removal of nitric oxide and carbon monoxide from exhaust gases. The influence of several catalyst variables has been investigated. The activity per volume of catalyst increases with increasing loading, while the intrinsic activity shows a maximum around C/M=100−50. An optimum catalyst for nitric oxide reduction and carbon monoxide oxidation has a copper/chromium ratio of 2/1. The apparent activation energy for the carbon monoxide oxidation over carbon supported copper-chromium catalysts is 77 kJ/mol, suggesting that the Cu---O bond rupture is the rate-limiting process. The reduction of nitric oxide takes place at higher temperatures. Since all catalysts have a low selectivity for molecular nitrogen formation at lower temperatures, the dissociation of nitric oxide is probably rate determining, resulting in a slightly reduced catalyst system. In an excess of carbon monoxide the reaction is first-order in nitric oxide and zero-order in carbon monoxide. Moisture inhibits the reaction by reversible competitive adsorption, whereas carbon dioxide does not. Oxygen completely inhibits the reduction of nitric oxide due to the more rapid reoxidation of the catalytic sites compared to nitric oxide. Therefore, the reduction of nitric oxide takes place only when all oxygen has been converted and, hence, is shifted to higher temperatures. As a possible consequence, the production of nitrous oxide is reduced. Nitric oxide and molecular oxygen react preferentially with carbon monoxide, so, in an excess of oxidizing component, gasification of the carbon support occurs at higher temperatures after carbon monoxide has been completely consumed.     

Feasibility analysis of membrane reactors – discovery of reactive arheotropes

A feasibility analysis methodology adopted from reactive distillation is applied to membrane reactors. A model is formulated to depict the reactive liquid phase composition on the retentate side of a continuous type membrane reactor. The effects of both the chemical reaction kinetics and the membrane mass transfer kinetics on the feasible products are elucidated by means of retentate phase diagrams and bifurcation analysis. The proposed method can be applied to various membrane processes, independent of the specific structure of the membrane. Two quaternary reaction systems are considered to illustrate the methodology. In the first hypothetical system, it is shown how selective membranes can influence the sequence of effective volatilities which in turn affects the feasible products of the system. In the second example of practical importance, i.e. the heterogeneously catalysed synthesis of propyl acetate coupled with permeation through a porous polycarbonate membrane, the dusty gas model is applied to describe the component fluxes through the membrane. For the latter reaction system, the existence of reactive arheotrope is demonstrated. Arheotropes represent mass transfer controlled feasible products of membrane separation process.     

Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

探讨电石法PVC烟气治理方法

分析了电石法PVC生产链中电石炉烟气及电厂烟气二氧化硫的排放情况,指出利用电石炉烟气中的CO合成氨、再将合成氨用于燃煤电厂烟气的"氨法"脱硫是具有较大应用潜力的循环经济产业链。     

Effect of surfactants and liquid hydrocarbons on gas hydrate formation rate and storage capacity

Hydrate formation rate plays an important role in making hydrates for the storage and transport of natural gas. Micellar surfactant solutions were found to increase gas hydrate formation rate and storage capacity. With the presence of surfactant, hydrate could form quickly in a quiescent system and the energy costs of hydrate formation reduced. Surfactants (an anionic surfactant, a non‐ionic surfactant and their mixtures) and liquid hydrocarbons (cyclopentane and methylcyclohexane) were used to improve hydrate formation. The experiments of hydrate formation were carried out in the pressure range 3.69–6.82 MPa and the temperature range 274.05–277.55 K. The experimental pressures were kept constant during hydrate formation in each experimental run. The effect of anionic surfactant (sodium dodecyl sulphate (SDS)) on natural gas storage in hydrates is more pronounced compared to a non‐ionic surfactant (dodecyl polysaccharide glycoside (DPG)). The induction time of hydrate formation was reduced with the presence of cyclopentane (CP). Cyclopentane and methylcyclohexane (MCH) could increase hydrate formation rate, but reduced hydrate storage capacity The higher methylcyclohexane concentration, the lower the hydrate storage capacity. Copyright © 2003 John Wiley & Sons, Ltd.     

谢尔渣油气化油改气控制系统的改造

介绍了Shell渣油气化装置将渣油原料改为天然气时控制系统的改造方案。提出的改造思路不但可用于Shell渣油气化，也可用于德士古渣油气化的油改气工程中。     

Understanding and Modeling the Effect of Surfactants in Enhanced Particle Removal from Surfaces in Aqueous Media

The removal of particulate contamination is a critical issue for many manufacturing processes. It is particularly critical to the electronics industry in which small pieces of microscopic debris remaining after chemical mechanical planarization (cmp) using submicron polishing particles can cause device failure. One way to enhance particle removal following the cmp process is to utilize surfactants. Recent research has shown ways to model the effect of surfactants on enhanced particle removal. However, previous research has not demonstrated the effect of ionic strength on enhanced particle removal associated with surfactant use. Past research has also not shown the combined effects of ionic strength and surfactant concentration on enhanced particle removal using surfactants. This article summarizes the parameters affecting particle removal, and it provides data and analysis on the effect of ionic strength as well as the combined effects of ionic strength and surfactant concentration on particle removal following cmp processing.     

Characterization and modification of fillers for paints and coatings

This paper highlights the possibility of inverse gas chromatography for the surface characterization of common fillers (CaCO₃, talc, SiO₂,) for paints and coatings. Divided solids are described, on the one hand, by the dispersive component of their surface energy and, on the other, by a specific parameter indicating their acid-base interaction potential. The role of the surface morphology at a molecular level is also examined. It is demonstrated that steric effects play an important role in the adsorption of probes on lamellar solids like talc. The consequences of surface treatments as well as examples of practical applications are also reported.     

Cyclamate intake and cyclohexylamine excretion are not related to male fertility in humans

Cyclamate and its metabolite cyclohexylamine affect male fertility in high dose animal studies, but this affect has not been investigated in epidemiological studies. This paper reports the first epidemiological study designed to investigate the possibility of a relationship between cyclamate and cyclohexylamine and male fertility in humans, in which 405 cases of clinically defined infertility in men and 379 controls were surveyed. Semen evaluation, urine analysis for cyclamate and cyclohexylamine and dietary questionnaires were compared between cases and controls. No evidence was found of a significant association between cyclamate intake and male infertility; neither high cyclamate nor high cyclohexylamine excretion were associated with elevated risk. The lack of association remained after adjusting by age, area of residence, education, total energy intake and other variables. No significant correlations were observed between cyclamate intake, metabolism or excretion, and sperm count and motility. The results demonstrate no effect of cyclamate or cyclohexylamine on male fertility at the present levels of cyclamate consumption.