In Situ FTIR Study of the Formation of an Organosilane Layer at the Silica/Solution Interface

An FTIR experiment especially designed to study the growth of an organosilane layer at the interface between a solution and a flat silica surface is presented. High sensitivity is achieved by using the attenuated total reflection (ATR) technique in a liquid flow cell. The ATR crystal, either silicon or germanium, is covered with a very thin silica layer. Chemical reactions of a mono-and a di-hydrolyzable silane with the silica substrate have been investigated. The grafting of a submonolayer of the first reagent has been monitored by following the C-H and SiO-H vibrations. The density of grafted molecules has been estimated and information on the nature of the chemical bonding has been achieved. Evidence for the chain-polymerization of the dihydrolyzable silane at the substrate/solution interface has been inferred from the appearance of a Si-O-Si absorption band.     

Prediction of venturi scrubber efficiency used in an updraft gasifier cleaning train

The performance of a venturi scrubber in the removal of tar from gas in updraft gasification has been studied. The gasifier has been operated with a husk feed rate of 1.6 × 10^?4 kg/s. The venturi scrubber has been operated at a superficial gas velocity of 56.4 m/s at the throat. A wide variety of scrubbing liquids having surface tensions ranging from 0.026 to 0.072 N/m have been used. The Q_g/Q_l, has been varied in the range of 1000–8000. The tar separation efficiency η has been found to vary from 51 to 98.5%. A mathematical model, assuming steady-state operation, has been developed considering very high pseudosolubility of tar in the scrubbing liquids. The predicted values of η have been compared with experimental results. The model satisfactorily explains the tar removal efficiency of the venturi for Q_g/Q_l values ranging from 4000 to 8000 for all scrubbing liquids. The following correlation has been developed for predicting venturi scrubber efficiency: .     

Experimental and numerical simulation of lignite chemical looping gasification with phosphogypsum as oxygen carrier in a fluidized bed

Phosphogypsum (PG) is a solid waste produced in the wet process of producing phosphoric acid.Lignite is a kind of promising chemical raw material.However,the high sulfur of lignite limits the utilization of lig-nite as a resource.Based on fluidized bed experiments,the optimal reaction conditions for the production syngas by lignite chemical looping gasification (CLG) with PG as oxygen carrier were studied.The study found that the optimal reaction temperature should not exceed 1123 K;the mole ratio of water vapor to lignite should be about 0.2;the mole ratio of PG oxygen carrier to lignite should be about 0.6.Meanwhile,commercial software Comsol was used to establish a fuel reaction kinetics model.Through computational fluid dynamics (CFD) numerical simulation,the process of reaction in fluidized bed were well captured.The model was based on a two-fluid model and coupled mass transfer,heat transfer and chemical reac-tions.This study showed that the fluidized bed presents a flow structure in which gas and solid coexist.There was a high temperature zone in the middle and lower parts of the fluidized bed.It could be seen from the results of the flow field simulated that the fluidized bed was beneficial to the progress of the gasification reaction.     

Some aspects of the role of coal thermoplasticity and coke structure in coal gasification. 2. The effects of pressure and heating rate on dilatometric parameters and optical anisotropy development

An examination of the influence of pressure and heating rate on the thermoplastic properties of a weakly coking coal and of coal with various pitch-like additives was carried out using a high pressure dilatometer. Pressure up to 4 MPa markedly increased the swelling properties and increased the plastic range by decreasing the softening temperature, but the effects of pressure were strongly influenced by rate of heating with high heating rates enhancing the effects. Additions of tar or pitch also enhanced swelling at low pressure. The solid carbonization residues from the dilatometer were examined by polarized light microscopy to determine the content and composition of optically anisotropic species. The anisotropic content was increased by increases in pressure and heating rate and pitch additives enhanced the anisotropic content, especially at low pressure, without affecting the composition of the anisotropy. No direct correlations exist between the dilatometric parameters and the optical anisotropy but their dependence on the conditions emphasizes that when considering high pressure gasification of coal, it is necessary to obtain data under appropriate conditions.     

气流床水煤浆气化技术的应用现状及开发进展

气流床水煤浆气化是煤高效、洁净利用的一项关键技术。简述了具有代表性的气流床水煤浆气化技术的应用现状及开发进展,并分析了影响水煤浆气化的主要因素,如烧嘴、耐火砖、进料系统、激冷环等,提出了一些改进措施。     

大化肥煤代油CO耐硫变换工艺流程的设计

分析石脑油制氨装置改扩建为水煤浆制氨装置ＣＯ耐硫变换工艺的特点，具体阐述其工艺流程优化设计中需考虑的主要技术问题。     

中氮肥煤造气技术改造调查与评述（上）

重点调查了９０年代以来，全国以煤焦为原料的中氮厂造气工序技术改造的基本情况，对技术改造的效果和存在的问题作了全面的评述，为各企业技术改造提供了一份可借鉴和参考的资料     

发挥贵州煤资源优势,加快煤化工的发展

对贵州煤化工现状进行的描述，指出从煤气化路线出发，以煤制合成气制得氮和甲醇为重点，建立大型煤化工装置并发展其下游产品，是贵州当前煤化工发展的方向。