存储媒体的媒体内同步反馈控制算法

本文提出了一种存储媒体的媒体内同步反馈控制算法，该方案是建立在缓冲区占用率控制基础上，通过周期性地检查缓冲区的占用情况来检测失步，并将其反馈给发送方，由发送方对发送帧速率进行调整。文章给出了接收方所需缓冲区的设计准则及发送帧速率的调整方法，并分析了算法中各参数对同步性能的影响。实验表明该方案能够处理由于网络传输时延特性变化引起的失步，与其它反馈控制方案相比具有更低的数据丢弃率，从而使接收端播放平滑连续，具有良好的视频播放质量。     

SECANT-FUZZY LINEAR REGRESSION METHOD FOR HARMONIC COMPONENTS ESTIMATION IN A POWER SYSTEM

In order to avoid unnecessary damage of electrical equipments and installations,high quality power should be delivered to the end user and strict control on frequency should be made, Therefore, it is important to estimate the power system's harmonic components with higher accuracy. This paper presents a new approach for estimating harmonic component in a power system using secant - fuzzy linear regression method. In this approach the non - sinusoidal voltage or current waveform is written as I linear function. The coefficient of this function is assumed to be fuzzy number with a membership function that has center and spread value. The time dependent quantity is written as Taylor series with two different time dependent quantities. The objective is to use the sample obtained from the transmission line to find the power system harmonic components and frequencies. We used an experimental voltage signal from a sub power station as a numerical test.     

A Novel Segmentation and Feedback Model for Resolving Contention in Optical Burst Switching

A novel segmentation and feedback model (SFM) applied to resolve contention is proposed. Simulation and performance analyses show that the SFM effectively avoids contentions in optical burst switching (OBS). The long delay time of deflection routing and the immature technology of wavelength converters and optical buffers are not deployed in the SFM. The SFM does not only realize fast switching but also allows preemption by higher priority bursts.     

First Harmonic (2f) Characterisation of Resonant Frequency and Q-Factor of Micromechanical Transducers

In this paper, the response to the first harmonic component (2f) of the electrostatic force in single terminal driven electrostatic comb-drive and parallel-plate drive was used as a signal to extract device parameters, namely, the Q-factor and resonant frequency instead of the fundamental (1f) resonance response. It is shown that the difficulty in motional measurement due to electrical cross-talk (parasitics) using 1f measurement can be overcome with a higher signal-to-noise ratio of the 2f signal. Both atmospheric (low-Q) and reduced pressure environment were investigated using off-chip electronics and lock-in amplifier. The measurements were done on the electrostatic comb-drive and capacitive parallel plate sensing plates that form the two core modules of a yaw rate sensor (dual-axis resonator). The effects of AC and DC bias voltages on the measured response have been investigated. Experimental amplitude and phase response data have been analysed using the Lorentzian curve-fit, Resonance Curve Area (RCA) method, the half-power bandwidth method (3 dB) and the Nyquist plot for data fitting and determination of the Q-factor and resonance frequency.     

Analysis and Optimization of Noise in Bipolar RF Harmonic Mixers

A noise analysis of bipolar harmonic mixers (BHM) used for direct-conversion receivers is presented in this paper. Analytical and simulated results for the transfer function of the mixer are presented. Simple analytical expressions describing noise contribution from all sources are derived. Estimation of flicker noise quite agrees with harmonic-balance simulation results. Based on the derived expressions, total time average noise power spectral density (PSD) at the output is compared with simulation results. For the recommended regions of operation, error is less than 20%. The overall BHM noise figure (NF) is calculated and optimized based on a simple extracted formula. Errors introduced by analysis remain within a 1.5-dB margin with respect to simulation results. The validity of analysis for high frequencies is justified. The effect of flicker noise coefficient on the overall mixer NF is compared for different available processes.     

光电双基区晶体管(PDUBAT)的器件模型

本文在考虑了晶体管的小注入效应和大注入效应以及基区宽变效应等因素后,首次用近似和简化的数学表示式和相应的等效电路,描述了光电双基区晶体管(PDUBAT)负阻形成的机理并使负阻区和谷值区的理论计算和实验结果一致性很好.     

彩色多频同步显示器行激励级电路的倒推设计法（1）

行激励级电路的设计是完全为行输出级服务的,它实质上是行输出级电路设计的一个重要而不可分割的组成部分。因此行激励级电路的设计,自然采用了从显象管偏转线圈和行输出管到激励变压器和行激励级的倒推设计法。     

In-situ monitoring and control for MOCVD growth of AlGaAs and InGaAs

We have used spectroscopic ellipsometry to perform real-time monitoring during metalorganic chemical vapor deposition growth of AlGaAs (on GaAs) and InGaAs (on GaAs and InP). Optical constants for these materials were obtained up to growth temperatures of 600 to 700°C. This information permits real-time extraction of composition and layer thickness from the raw ellipsometric data at sample rates on the order of 0.5 Hz. We describe closed-loop control of composition and total layer thickness on AlGaAs-based structures, including Bragg reflectors. In-situ data obtained on double-heterostructure quantum-well laser structures demonstrate that spectroscopic ellipsometry is an extremely powerful monitoring and quality-control tool, giving important real-time information on complex structures that would be difficult and time-consuming to obtain after growth.     

Steady-state torque control system with secondary-current feedback for three-phase squirrel-cage induction motors

This paper presents a highly stable steady-state torque control system with a feedback of a secondary current signal. The torque control system is constructed with a feedback of the secondary current (I₂) signal using a quick response magnetic-field sensor constructed with an amorphous core multivibrator bridge, which can solve the secondary resistance change problem for temperature variation in the IM. Moreover, we added a state feedback to the system to improve the response speed for the unit step function of a torque order. The I₂ sensor method has advantages especially at a low-speed range, in which conventional method using an integrator shows control errors.     

离散事件动态系统的代数模型及其控制器的分析计算

本文在离散事件动态系统的Ｐｅｔｒｉ网图形描述的基础上建立了相应的代数模型，该模型可以用来计算无竞争无回路Ｐｅｔｒｉ网的“最大状态”；该“最大状态”的计算在本文给出的动态反馈控制器中得到了应用。