基于激光多普勒测速法的2×106m/s2高冲击校准技术

在高冲击传感器动态性能校准中,实现高量程、宽脉冲激励是目前高冲击校准急需解决的问题。采用速度改变法校准原理,以气炮为激励源,利用激光多普勒测速方法测量砧体运动速度,建立高冲击校准系统。分析碰撞系统的作用原理,提出调整和控制激励脉宽的方法;分析测速误差,提出双光束差动侧向测速方法。实验结果表明:高冲击校准系统校准量程为2×106m/s2,激励脉宽在2×106m/s2时大于100μs,校准冲击灵敏度的扩展不确定度小于5%(k=2)。     

A copper/polyimide Metal-base packaging technology

A unique substrate MCPM (Mitsubishi Copper Polyimide Metal-base) technology has been developed by applying our basic copper/polyimide technology.¹ This new substrate technology MCPM is suited for a high-density, multi-layer, multi-chip, high-power module/package, such as used for a computer. The new MCPM was processed using a copper metal base (110 × 110 mm), full copper system (all layers) with 50-μm fine lines. As for pad metallizations for the IC assembly, we evaluated both Ni/Au for chip and wire ICs and solder for TAB ICs. The total number of assembled ICs is 25. To improve the thermal dispersion, copper thermal vias are simultaneously formed by electro-plating. This thermal via is located between the IC chip and copper metal base, and promotes heat dispersion. We employed one large thermal via (4.5 mm^?) and four small vias (1.0 mm^?) for each IC pad. The effect of thermal vias and/or base metal is simulated by a computer analysis and compared with an alumina base substrate. The results show that the thermal vias are effective at lowering the temperature difference between the IC and base substrate, and also lowering the temperature rise of the IC chip. We also evaluated the substrate’s reliability by adhesion test, pressure cooker test, etc.     

Solid-liquid phase equilibria of benzene + 2-methyl-2-propanol system under high pressures

Solid-liquid phase equilibria of the benzene + 2-methyl-2-propanol system have been investigated at temperatures from 278 to 323 K and pressures up to 300 MPa using a high-pressure optical vessel. The uncertainties of the measurements of temperature, pressure and composition are within ±0.1 K, ±0.5 MPa, and ±0.001 mole fraction, respectively. The freezing pressure at a constant composition increases monotonously with pressure. The eutectic point shifts to a higher temperature and benzene-rich composition with increasing pressure. In order to describe the pressure-temperature-composition relation of high-pressure solid-liquid phase equilibria, a new simple equation has been proposed as follows:

���׸ߵ����ѷ��ݻ�����ԭʼ�������㷽��̽��

本文把与井简直接连通的大裂缝及井筒定义为“裂缝—井筒系统”,通过气体状态方程的变换和续流总量的计算,探索出井底大裂缝的容积及其储量的计算方法。     

Use of electron microscopy on microstructure characterization of high chromium cast irons

The physical metallurgy underlying the development of cast microstructures in abrasion resistant high chromium cast irons, and their structural modification by thermal treatments is relatively complex. Structural characterisation via electron microscopy therefore has a key role to play in furthering our understanding of the phase transformations that control the microstructures and hence the service performances of these irons as wear parts. This paper shows how both scanning and especially transmission electron microscopy can provide valuable information on the nature of eutectic and secondary carbides and on the matrix structures in these irons. Particular attention is given to current characterisation research on conventionally cast 30%Cr irons that are used for applications involving corrosive wear e.g. slurry pumps and on a semi-solid cast 27%Cr iron that has a potential for applications in industry.     

提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。     

高沸点溶剂法合成原乙酸三甲酯

对低沸点溶剂法制备原乙酸三甲酯工艺进行了改进，比较了煤油、2-乙基己醇、氯苯、异佛尔酮、邻苯二甲酸二丁酯、乙二醇二丁醚等高沸点溶剂对反应的影响，筛选出最优高沸点溶剂煤油：研究了新反应体系的醇解pH值、溶剂的循环使用次数对反应的影响及溶剂循环损耗率，结果表明，醇解的最佳pH值为5．6；随着溶剂循环次数增加，原乙酸三甲酯收率从83．6％(1次)逐渐下降到76．7％(16次)；溶剂次平均损耗率4．6％。实现了直接蒸馏产品，溶剂循环使用的新工艺。避免了旧工艺先蒸溶剂，后蒸产品，产品大量分解，收率低等缺点。     

High solids content emulsions. III. Synthesis of concentrated latices by classic emulsion polymerization

Two different methods of producing bi‐ and trimodal latices of a mixture of methyl methacrylate, butyl acrylate, and small amounts of acrylic acid were tested. It is shown that a combination of concentrating blends of seed particles by semibatch reaction, followed by a nucleation of small particles plus a second semibatch phase allowed us to obtain stable latices with solids contents over 65% and viscosities of below 2500 mPa s^?1 with little coagulum formation. The key parameter in determining latex stability, coagulum formation, and viscosity appears to be the the particle size distribution, and especially its modification attributed to secondary nucleation. Because it is not possible to eliminate water‐soluble monomers from the polymerization recipe, secondary (homogeneous) nucleation must be minimized by careful addition of the free‐radical initiator and choice of monomer feed flow rates. The nucleation of the third population in the trimodal latices is best accomplished with a mixed surfactant system because renucleation by anionic surfactant alone leads to detrimental changes in the particle size distribution (PSD) resulting from excessive flocculation of particles. In addition, it was found that the viscosity of the final products was not sensitive to small changes in the ionic strength of the latex, although neutralization to a pH of 6 effectively doubles the final latex viscosity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1916–1934, 2002; DOI 10.1002/app.10513     

悬浮法合成聚丙烯腈高吸水性树脂

以偶氮二异丁腈为引发剂，用悬浮聚合法合成了交联聚丙烯腈，然后对其进行水解，得到了高吸水性聚丙烯腈。交联剂用量和水解条件对树脂吸水倍数的影响很大。树脂吸去离子水倍数为420倍，平均粒径为250μm。