冗余技术在维持DCS系统稳定运行中的作用

以浙江中控JX300-XP为例,介绍冗余系统在系统长周期运行中的关键作用。     

Authority updating: An expert authority evaluation algorithm considering post‐evaluation and power indices in social networks

In group assessment, the focus is on finding high‐authority experts to improve the reliability of assessment results. In this study, we propose an authority updating algorithm while considering the power and judgement reliability of an expert on the basis of social networks and post‐evaluations. A network power index is established and used to reflect the power of an expert while considering social networks. The measurement of the judgement reliability of an expert considers the post‐evaluation of the objects selected by experts, thereby more scientifically reflecting the reliability of experts. The analysis shows the following: although the social‐network structure influences the authority of experts, the influence weakens when the assessment group is a highly or even fully connected group; the network effect may increase the authority of some experts and reduce that of others, and it will weaken as the network connectivity increases; moreover, the judgement reliability and authority of an expert while considering post‐evaluation can encourage him/her to make fair assessments and strive to reduce his/her motivation and cognitive biases.     

Solid-liquid phase equilibria of benzene + 2-methyl-2-propanol system under high pressures

Solid-liquid phase equilibria of the benzene + 2-methyl-2-propanol system have been investigated at temperatures from 278 to 323 K and pressures up to 300 MPa using a high-pressure optical vessel. The uncertainties of the measurements of temperature, pressure and composition are within ±0.1 K, ±0.5 MPa, and ±0.001 mole fraction, respectively. The freezing pressure at a constant composition increases monotonously with pressure. The eutectic point shifts to a higher temperature and benzene-rich composition with increasing pressure. In order to describe the pressure-temperature-composition relation of high-pressure solid-liquid phase equilibria, a new simple equation has been proposed as follows:

可视化基站发电管理系统

针对以前的发电管理系统或只是数据呈现,提供市电及发电相关数据信息,或只是提供出车轨迹,主要实现对出车的管理,不能全面反应发电全过程且不便于对发电事件进行分析的情况,提出可视化发电管理系统的概念。在简要介绍了LBS系统、动力环境监控系统后,讲述了可视化基站发电管理系统的组成以及通过LBS定位管理、短信互动、实时监测数据等进行系统实现。可视化发电管理系统通过可视化的界面帮助发电管理人员进行管理,直观、便捷。     

Use of electron microscopy on microstructure characterization of high chromium cast irons

The physical metallurgy underlying the development of cast microstructures in abrasion resistant high chromium cast irons, and their structural modification by thermal treatments is relatively complex. Structural characterisation via electron microscopy therefore has a key role to play in furthering our understanding of the phase transformations that control the microstructures and hence the service performances of these irons as wear parts. This paper shows how both scanning and especially transmission electron microscopy can provide valuable information on the nature of eutectic and secondary carbides and on the matrix structures in these irons. Particular attention is given to current characterisation research on conventionally cast 30%Cr irons that are used for applications involving corrosive wear e.g. slurry pumps and on a semi-solid cast 27%Cr iron that has a potential for applications in industry.     

提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。     

变频开关电源Fuzzy-PID控制器的设计

针对感应式变频开关电源在对金属材料进行热处理过程中，负载的等效参数和谐振频率发生变化，而变频电源的输出频率不能及时调整和跟踪的问题，结合PID和Fuzzy控制技术的优点，设计Fuzzy-PID控制器对变频电源进行控制，在大偏差时用Fuzzy控制，在小偏差时用PID调节。Fuzzy-PID控制器以单片机8098为核心，采用SPWM专用芯片SA4828，实现变频开关电源的电压、电流双闭环控制，使变频电源不仅具有较快的动态响应、更小的超调，并且具有较高的稳态精度和频率跟踪控制特性。     

High solids content emulsions. III. Synthesis of concentrated latices by classic emulsion polymerization

Two different methods of producing bi‐ and trimodal latices of a mixture of methyl methacrylate, butyl acrylate, and small amounts of acrylic acid were tested. It is shown that a combination of concentrating blends of seed particles by semibatch reaction, followed by a nucleation of small particles plus a second semibatch phase allowed us to obtain stable latices with solids contents over 65% and viscosities of below 2500 mPa s^?1 with little coagulum formation. The key parameter in determining latex stability, coagulum formation, and viscosity appears to be the the particle size distribution, and especially its modification attributed to secondary nucleation. Because it is not possible to eliminate water‐soluble monomers from the polymerization recipe, secondary (homogeneous) nucleation must be minimized by careful addition of the free‐radical initiator and choice of monomer feed flow rates. The nucleation of the third population in the trimodal latices is best accomplished with a mixed surfactant system because renucleation by anionic surfactant alone leads to detrimental changes in the particle size distribution (PSD) resulting from excessive flocculation of particles. In addition, it was found that the viscosity of the final products was not sensitive to small changes in the ionic strength of the latex, although neutralization to a pH of 6 effectively doubles the final latex viscosity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1916–1934, 2002; DOI 10.1002/app.10513     

POWER CONSUMPTION WITH ANCHOR MIXERS EFFECT OF BOTTOM CLEARANCE

The effect of bottom clearance on power draw for anchors is investigated. The results suggest that power input decreases as the bottom clearance ratio b/D increases. A new correlation is proposed in which both bottom and wall clearance effects on power input are considered. The dependence of power input on these effects is additive rather than multiplicative. Thus, the total power consumption is the sum of the power inputs generated by the wall and bottom clearance. Power results from 3D-CFD numerical simulations are also presented. These results confirm fairly well the experimental points.     

悬浮法合成聚丙烯腈高吸水性树脂

以偶氮二异丁腈为引发剂，用悬浮聚合法合成了交联聚丙烯腈，然后对其进行水解，得到了高吸水性聚丙烯腈。交联剂用量和水解条件对树脂吸水倍数的影响很大。树脂吸去离子水倍数为420倍，平均粒径为250μm。