Non-equilibrium particle motion in the vicinity of a single blade

The motion of sand particles close to a single moving blade was investigated using Positron Emission Particle Tracking (PEPT) during the period in which the free bed surface profile was evolving to an equilibrium shape. The area affected by the blade was divided into active and inactive regions and these were analysed separately. The characteristic heart-shape of the active region in the plan view was determined. An approximately 10-particle-diameter wide velocity transition zone is found between the two regions. While the tracer particle is in the inactive region moving away from the blade, the time dependence of the axial displacement is well described by a logarithmic relationship. The probability of particle movement towards the centre of the blade was quantified using a “central tendency” index. The calculated central tendency shows maxima at each side of the blade. The separation of the two maxima, which indicates the width of the active region, increases with fill level but is independent of rotational speed.     

光学材料的激光微加工研究进展与应用前景

综述了国内外在光学材料激光微加工方面的研究成果和应用状况，并展望了其发展前景。     

液力联轴器喷油着火事故的原因分析及预防

以矿用液力联轴器为研究对象 ,阐明其喷油着火的机理 ,分析其喷油着火的原因并作出事故树分析 ,针对现场使用的情况 ,提出预防措施及发展趋势 ,对矿井安全生产具有指导性作用。     

声诱饵仿真试验系统

介绍了声诱饵仿真试验系统的组成、工作原理、对接装置结构等,建立了对接装置声耦合状态下的数学模型,对近场声压分布进行了仿真计算,得出了匹配材料厚度、发射和接收换能器的选取原则。     

Investigation into polishing process of CVD diamond films

A new technique used for polishing chemical vapor deposition (CVD) diamond films has been investigated, by which rough polishing of the CVD diamond films can be achieved efficiently. A CVD diamond film is coated with a thin layer of electrically conductive material in advance, and then electro-discharge machining (EDM) is used to machine the coated surface. As a result, peaks on the surface of the diamond film are removed rapidly. During machining, graphitization of diamond enables the EDM process to continue. The single pulse discharge shows that the material of the coated layer evidently affects removal behavior of the CVD diamond films. Compared with the machining of ordinary metal materials, the process of EDM CVD diamond films possesses a quite different characteristic. The removal mechanism of the CVD diamond films is discussed.     

正确选用热力管网保温材料的几个问题

介绍了做好热力管网保温应具备的有关知识和数据，以及宝钢蒸汽主干管网在采用四种保温材料下的经济保温层厚度和相对的节能效益，认为目前适于宝钢公司热源温度在６００℃以下较好的保温材料有新型矿渣棉制品和泡沫石棉板。     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

液压伺服马达拖动研究

液压伺服马达拖动和液压伺服加载 ,目前列为液压技术研究的前缘学科。本文专门从液压伺服马达进行探讨。     

湿硫化氢环境下的球罐腐蚀状况分析

在湿硫化氢环境下 ,尤其储存介质中的硫化氢含量超标时 ,很容易对储存容器壳体 (含焊缝和母材 )造成硫化氢应力腐蚀或氢鼓包。作者较仔细分析了 1 0 0 0m3 丙烯球罐产生硫化氢应力腐蚀开裂和40 0m3 LPG球罐产生氢鼓包的原因。提出了此类设备在设计选材、设备制造、施工安装和使用维护等环节应注意的问题。     

天然多糖类/蛋白质复合材料的研究进展

在参考了 31篇文献的基础上 ,详述了天然多糖类与蛋白质复合材料的研究进展