C60辅助下ZnNiS光催化分解水制备氢气的研究

通过在光催化剂掺杂ZnS中加入球笼化合物富勒烯C60,提高了光催化水分解的效率.并采用气相色谱法跟踪反应,发现氢气释放量是未加C60时的4倍多.同时,对该催化反应的机理进行了初步的探讨.     

Coal liquefaction using a hydrogenated creosote oil solvent: H-atom transfer from hydrogen donor components in the solvent

The presence of hydroaromatic, hydrogen donor components in a coal-derived solvent is one of the more important factors in the successful operation of a non-catalytic coal liquefaction process. Various hydrogen donor species present in a hydrogenated creosote oil have been identified. Their rate of disappearance under conditions that are consistent with a short residence time coal liquefaction process has been used to rank the reactivities of the various hydrogen donors. 1,2,3,10b-Tetrahydrofluoranthene was found to be an exceptional donor while 4,5-dihydropyrene, the hexahydropyrenes and 9,10-dihydrophenanthrene were found to be quite active. Sym.-octahydrophenanthrene and 2a,3,4,5-tetrahydroacenaphthene exhibited moderate activity. Tetralin and the four methyltetralin isomers were found to be unreactive under the coal liquefaction conditions employed.     

固定化微生物脱除工业酸性废气中H_2S的研究

以H 2软性填料作为氧化亚铁硫杆菌的固定化载体 ,构成了固定床生物反应器。在一定操作条件下 ,考察了固定床生物反应器对Fe2 +的氧化速率 ,最大可达 7.6 7g/ (L·h)。并对固定床生物反应器运行中在载体表面形成的络合物进行了研究 ,X射线衍射证明此络合物为黄钾铁矾 [KFe3(SO4 ) 2 (OH) 6]。     

MIP-CGP工艺专用催化剂CGP-1的开发与应用

阐述了生产汽油组分满足欧Ⅲ排放标准并多产丙烯的催化裂化工艺（简称MIP-CGP）专用催化剂（简称CGP-1）的研究开发与工业应用结果。CGP-1催化剂的基质具有良好的容炭性能，使活性组元受到良好保护，其优势作用在第二反应区得以充分发挥，具有更高的氢转移活性和强的汽油小分子烯烃裂化活性。中国石化九江分公司和镇海炼化公司的MIP-CGP工业试验标定结果表明，与常规FCC相比，采用CGP-1催化剂的MIP-CGP技术在生产烯烃体积分数小于18％的汽油组分的同时，丙烯产率达到8％以上。此外，汽油诱导期大幅提高，抗爆指数增加；总液体收率有所提高，干气产率下降，焦炭选择性良好。     

镍氢电池负极用低成本储氢合金的研究

研究了ABS型储氢合金在低Co含量条件下，随B组元替代元素Co，Al，Si等含量的变化对合金电化学性能的影响规律，同时研究了A组元中不同La／Ce比对合金电化学性能的影响情况。结果表明，随合金中Co含量的降低，合金的活化性能和放电容量得以改善，但合金的循环寿命下降也比较明显；在试验范围内，随Al元素的加入，合金的循环寿命得以改善，但材料的放电容量和活化性能均有所下降；随合金La／Ce比的降低，合金的放电容量略有下降，但其循环寿命和放电电压平台有较大提高。     

VRDS装置常压分馏塔系统的问题分析

胜利炼油厂重油加氢 (VRDS)装置的常压分馏塔为填料塔 ,2 0 0 1年检修开工后该系统出现异常 ,经过查找分析 ,确定轻烃 /产品减压渣油换热器和柴油汽提塔重沸器内漏是装置异常的主要原因     

注氢硅中微结构缺陷的TEM观察

通过透射电子显微镜观察到注氢硅片中存在损伤带，损伤带的位置和注人氢的分布几乎一致，推断损伤带是由于氢的注入引起的。损伤带内主要以平行于正表面的{111}面状缺陷为主，另外还有斜交于正表面的{111}面状缺陷以及{100}面状缺陷，这是由于氢朝能量低的位置的迁移聚集而形成的。在损伤带的中间还可见到晶格紊乱团块和空洞，这是由于损伤带中间存在高浓度的氢和高密度的面状缺陷面导致形成的。     

环氧大豆油增塑剂的合成

本合成采用无溶剂一步法环氧化工艺，取消了苯作溶剂，用新型催化剂代替硫酸，在稳定剂上用３０％双氧水合成的环氧大豆油，环氧值达９５％以上。     

Corrosion fatigue short crack growth behaviour in a high strength steel

The influence of an aggressive environment (0.6 M, aerated NaCl solution) on short fatigue crack initiation and growth behaviour has been studied. The study involved three major test series, namely: air fatigue, corrosion fatigue, and intermittent air fatigue/corrosion fatigue. The above tests carried out under fully reversed torsional loading conditions at a frequency of 5 Hz, showed that it was the non-metallic inclusions which took part in crack initiation resulting from debonding at metal matrix/inclusion interface and pitting of inclusions in both air and corrosove environments, respectively. Short fatigue crack growth results in these two environments obtained by using plastic replication technique, indicated a large effect of microstructure i.e. prior austenite grain boundaries. The stage/stages at which the environmental contribution was dominant has been discussed by considering the results achieved from intermittent tests. However, the mechanisms involved in corrosion fatigue short crack growth have also been described in the light of results obtained from futher investigations carried out by conducting corrosion fatigue tests under applied cathodic potential conditions and tests on hydrogen pre-charged specimens under air fatigue and uniaxial tension conditions.