基于8098单片机的伏安特性测量系统的设计

伏安特性测量技术有着广泛用途。本文介绍一种用８０９８单片机为控制核心的智能化通用伏安特性测量系统的设计要点。包括系统的硬件和软件设计，以及针对实际问题所采用的一些设计技巧。成果分析表明，采用８０９８单片机有着独特的优越性和推广价值。     

模拟集成温度传感器设计

介绍了一种模拟集成温度传感器的电路设计。该电路利用双极性晶体管基极-发射极结压降与热力学温度T成比例的关系来实现温度的测量,并在6μm双极工艺线上投片成功。该电路在常温25℃下输出298.2μA的电流,在-55℃～150℃的工作温度范围内的误差不超过±3℃,非线性度误差不超过±0.4℃。     

Citations do not solve problems.

D. T. Cambell and D. W. Fiske (1959) made the now-obvious statement that measures of the same variable made by different methods should agree (converge) and certainly should agree better than measures of different variables made by those several methods. Almost everyone accepted that statement, yet the multitrait–multimethod matrices published today show little or no improvement over the published examples cited in 1959. The article raised the conceptual problem of how a variable and its measurement should be linked and the methodological problem of clarifying the nature of methods and their effects. Given these unresolved problems, it is perhaps not surprising that the question of the appropriate statistical analysis of these matrices has also no consensual answer. Perhaps methods and traits or contents are so thoroughly intertwined that their interaction cannot be adequately analyzed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Overview of Tiber-II—Evolution toward an Engineering Test Reactor

TIBER II is designed to be a minimum size and cost candidate for an international Engineering Test Reactor. High-current density Nb₃Sn superconducting magnets with radiation-tolerant polymide insulation is combined with a minimum thickness tungsten inbored shield and a common, external vacuum boundary to minimize the inner radial build of the tokamak core. This results in a major radius of 3 m, compared to 5 m for previous ETR designs such as INTOR, with correspondingly lower costs expected. Cyclic stress fatigue limits the number of pulses so that steady-state current drive, based on a combination of neutral beams, lower hybrid and ECH, is designed to achieve reactor-relevant nuclear testing conditions (Fluence 3MW yr/m², rwall > 1 MW/m² in steady state).This report is abstracted from a more complete information document UCID-20863 with numerous authors. See Ref. l for complete credits.     

涡流检测技术在宝钢热轧轧辊上的应用

介绍了轧辊涡流检测仪的工作要求、设备组成和使用方法,指出对轧辊进行涡流检测可防止爆辊,减少轧辊磨削量。     

变频开关电源Fuzzy-PID控制器的设计

针对感应式变频开关电源在对金属材料进行热处理过程中，负载的等效参数和谐振频率发生变化，而变频电源的输出频率不能及时调整和跟踪的问题，结合PID和Fuzzy控制技术的优点，设计Fuzzy-PID控制器对变频电源进行控制，在大偏差时用Fuzzy控制，在小偏差时用PID调节。Fuzzy-PID控制器以单片机8098为核心，采用SPWM专用芯片SA4828，实现变频开关电源的电压、电流双闭环控制，使变频电源不仅具有较快的动态响应、更小的超调，并且具有较高的稳态精度和频率跟踪控制特性。     

3种高电流密度离子膜电解槽的性能对比与介绍

目前离子膜电解槽的发展方向为复极、自然循环、高电流密度、低电耗，伍德诺拉公司BM2．7-Ⅲ型槽、美国西方化学公司ExL^B-65槽、日本氯工程公司BiTAC-858槽即具有这些先进性能。对这3种槽进行了介绍与对比。     

外加电流阴极保护在海水冷却槽中的应用

论述了金属的电化学腐蚀和外加电流阴极保护原理。说明对以海水为介质的冷却、冷凝设备,采用外加电流阴极保护是防止设备腐蚀的有效方法。举例说明了应用效果。     

直流电桥法测量电缆故障点的距离

迅速、准确地探测故障点的位置对保证故障电缆的及时修复有着重要意义。介绍了电缆故障的性质和直流电桥法测量电缆故障点距离的原理，着重阐述了几种常用的电缆接地故障的测量方法，并提出在实际生产、施工中，应根据具体情况选取合理的仪器及测量方法，迅速、准确地探测故障点的位置，以保证故障电缆的及时修复。     

Cycling hardening and serration yielding of Fe-Ni-Cr alloy at high temperature under out-phase TMF

Behaviour of hardening and serration yield of a Fe-Ni-Cr alloy under isothermal cycling (ISC) and out-phase TMF was studied on the basis of varied hysteresis loops. Cycling hardening and serrated yielding for ISC depend on the temperature and the total strain range, stronger hardening with serrated yielding at higher strain range under ISC at 600 °C, but no hardening and serrated yielding occurred under ISC at 800 °C. Stronger hardening with stress serration occurred at the thermal path going to the lowest temperature, no stress serration occurred at the highest temperature under the out-phase. The hardening also depends on the total strain range, higher total strain range with lower cycling temperature resulted in a stronger hardening and remarkable serration yielding behavior. Weaker hardening without serrated yielding occurred at near 800 °C may due to an obvious cycling stress drop under out-phase TMF. Change in the shape of the hysteresis loops also expresses the degree of the damage of the tested alloy under out-phase and ISC.