Flashover voltage characteristics of contaminated station insulators under temporary ac overvoltages in the ac system connected with a frequency converter station

According to the recent analysis results of temporary ac overvoltage in the ac system connected with a frequency converter station, large-magnitude over-voltages were confirmed to occur under some special system conditions. Most of the station insulators currently used cannot withstand such overvoltages according to an evaluation based on the data obtained earlier. The necessity of tests to be done to evaluate such performance more accurately was recognized. Both power frequency and switching impulse overvoltage flashover tests were made on contaminated insulators by the method well simulating the natural wetting condition. Switching impulse flashover voltage with the waveshape having a long wavefront time of 2 ms can be well correlated with the flashover voltage characteristics of temporary ac overvoltage. Higher flashover voltage characteristics were obtained by a clean fog test method compared with those obtained by equivalent fog test method.     

用于高压电容器的SrTiO3基陶瓷

报道ＳｒＴｉＯ３基陶瓷的制备方法和介电性质，给出了用此种陶瓷制成的高压电容器的试验结果，并对它位进行了讨论。     

蒸汽发生器二次侧清洁度的视频检查

立式平管板Ｕ形管束的压水堆核电站蒸汽发生器安装至瞬变工况期间，管板上表面的铁基金属残余物的堆积和外来物的存在，以及商业运行后管板、传热管、管子支撑板等的低流速区域里沉积物的堆积要求进行蒸汽发生器的清洁度检查。介绍了蒸汽发生器二次侧清洁度的视频检查技术。该技术适用于蒸汽发生器安装至瞬变工况和投入商业运行后可能发生污染的各阶段的清洁度检查。     

航空油品高频/高压电脱水微观机理

设计并建立了一套高压电物理化学显微分析装置，为研究高压电物理化学领域的微观机理提供了一种新的技术途径。采用该技术，研究了胜利稠油经6％加氢裂解柴油稀释的原料油的高频／高压电脱水的微观机理。该原料的脱水率达96．7％，高于传统的电脱水方法。     

单稳态触发器的结构及其开关级设计原理

根据单稳态触发器定时单元特性,提出了单稳态触发器的一般结构.在此基础上,运用传输电压开关理论进行了CMOS单稳态触发器的开关级设计研究,并具体设计了两个单稳态触发器.设计实例表明文中提出的方法不仅简单、有效,而且具有通用性.     

镁法海绵钛生产工艺中大型无隔板镁电解槽的节能实践

以镁法海绵钛生产工艺中大型无隔板镁电解槽的实际节能情况为例，探讨了在镁电解生产中的非生产耗电、生产耗电、漏电等因素造成的能量浪费，阐述了生产中粗镁直流电耗、电流效率、工作电压3者之间的关系，指出了影响电解槽工作电压的有关因素及降低电解槽工作电压的途径。     

Experimental Study about Activated Water Generated by the Electro—hydraulic Impulse Strengthening the Mechanical Performance of Concrete

On the basis of a great number of experiments, it is proved that the strength of concrete is improved greatly when it is mixed with activated water produced by the electro-hydraulic impulse.With the proper parameters, the compression strength of concrete can be increased by 45% .The reason for improvement of concrete strength by using activated water is discussed from the aspect of the structure of molecule.     

配网侧接入电源对负荷建模的影响

研究了配网侧接入电源对负荷建模的影响。发现当配网侧电源的发电容量逐渐增大时，原有的感应电动机并联恒阻抗、恒电流、恒功率（ZIP）模型的负荷模型将不再能很好地反映该区域的负荷特性，进而提出了一种新的负荷模型结构———异步发电机并联ZIP模型。通过仿真计算，验证了该新负荷模型的有效性，并进一步统一了上述2种负荷模型，称为异步机并联ZIP负荷模型。     

接地故障保护的设置和整定(三)

7 TT系统接地故障保护 TT系统的电源中性点直接接地,而电气设备的外露可导电部分则经各自的PE线接地。这样在大多数情况下,由于故障回路包括两个接地电阻,使接地故障电流太小,不足以使过电流保护动作切断接地故障电流。而且由于故障电流小,故障点未被熔焊,故障点阻抗是难以估计的接触电阻。因此,TT系统接地故障回路阻抗和故障电流难以估算。所以,必须设置漏电电流动作保护。     

Mg-doped LiNi0.5Mn1.5O4 spinel for cathode materials

Lithium-ion batteries are becoming more and more important not only for portable electronic devices, but also in prevision of high power electric vehicles. In such an optic, deep studies regarding all the components of a secondary battery are in development. In this study, high voltage cathode materials have been selected. Crystals with spinel structure have a 3D vacancy pathway suitable for Li-ions transport. The material under study was LiNi_0.5Mn_1.5O₄ doped with magnesium replacing the nickel. Various samples were synthesized via three different routes: a solid-state method, a modified sol–gel method and a xerogel method. The structure and morphology of the powders were analyzed with HRTEM and XRD. Electrochemical tests were also performed. A wide range of particle sizes (from micro to nanosize) was the result of the different synthesis routes. Unfortunately pure materials were not always obtained. The electrochemical tests showed improvement of the material's cyclability, by reducing the particle size. The electrochemical tests further confirmed the existence of a Li_1+dMn_2−dO₄ impurity. The results are quite promising, however, further improvement of the purity of the electrode composition are needed.