Adhesive Bonding of Oil-Contaminated Steel Substrates

Durability of adhesive bonds formed by curing epoxies against oil-contaminated steel substrates using amidoamine curing agents was determined during exposure to boiling water. The most durable bonds were obtained using amidoamine curing agents with relatively low amine numbers and by blending silane coupling agents such as γ-glycidoxypropyltrimethoxysilane (γ-GPS) and N-(2-aminoethyl)-3-aminopropyltrimethoxy silane (AAMS) into the adhesives. When X-ray photoelectron spectroscopy (XPS) was used to characterize the failure surfaces of the adhesive joints after exposure to boiling water, it was determined that adhesives prepared using amidoamine curing agents with low amine numbers were able to displace the oil from the steel surface but adhesives prepared with amidoamine curing agents with high amine numbers were not. Results obtained from XPS also showed that the amino groups on the substrate fracture surfaces of joints prepared using curing agents with low amine numbers were protonated whereas the amino groups in the bulk adhesive were not, indicating that there was a chemical interaction between the curing agent and the hydrated surface of the substrate. It was also shown using infrared spectroscopy that the amidoamine curing agents formed salts with calcium compounds in the oil.     

基于红外传感原理的无人机姿态测量系统设计

由于红外温度传感器能有效感知天空间的热辐射,并且相比传统姿态测量的传感器具有体积小、重量轻、成本低等特点,设计一种基于红外传感原理的无人机姿态测量系统;该系统以新型的ARM Cortex—M3内核微处理器STM32F103ZET6作为处理单元,通过采集红外传感器的姿态信息,进行姿态解算,进而获得无人机的姿态角;同时分析了太阳干扰对实验的影响。实验测试表明:该姿态测量系统简单实用,性能稳定,精度高,能有效满足一般无人机姿态测量的要求。     

涂料原料和涂层厚度对反射隔热保温性能影响研究

通过研究涂料配方中所用乳液、颜料、常规填料和隔热填料在红外灯下的反射、隔热和保温性能，发现高折射率的二氧化钛和含有微孔的硅藻土具有最佳的反射和隔热保温效果，轻质碳酸钙和重质碳酸钙具有一定的隔热保温作用，而理论上具有隔热保温效果的填料海泡石等并没有预期的效果。涂层厚度对隔热保温效果具有一定影响，但是没有颜料和填料的影响大。隔热涂料使用的填料应含有硅藻土、二氧化钛以及一些常规的填料。     

基于STM32的多相LED穹形光源控制系统设计

针对工业视觉检测中对光源的照射角度、光源亮度、颜色等调节要求,设计了一种基于STM32的多相LED穹形光源控制系统,给出了系统实现方案及各模块具体实现,实现了光源参数的连续可调控制。     

一种基于悬浮吸收层的双层结构的热电堆红外探测器(英文)

提出一种新颖红外传感器,这种传感器采用悬浮吸收层的双层结构的优势,来实现相对小尺寸下的高探测性能。双层结构采用2种牺牲层材料,分别为聚酰亚胺牺牲层和预埋在热偶条和沉底之间的多晶硅材料。仿真结果证明了该种结构的探测率、响应率和响应时间分别达到2.85×108cm Hz(1/2)/W、1 800 V/W和6 ms。本文给出了该种热电堆红外探测器高度兼容于CMOS工艺的制备流程,使器件的高效量产和低成本生产成为可能。     

基于CMOS工艺钨微测辐射热计阵列集成芯片的设计与制作

采用0.5μm标准CMOS工艺和微机械加工工艺,设计并制作了低成本4×4钨微测辐射热计阵列集成芯片。阵列中每个钨微测辐射热计均由微悬桥结构和钨热敏电阻组成,CMOS读出电路集成在阵列下方。微悬桥结构由表面牺牲层技术实现,不需要任何的光刻工艺。钨微测辐射热计像元尺寸为100μm×100μm,填充因子为20%。测试结果表明,在真空环境下,钨微测辐射热计等效热导为1.31×10-4W/K,等效热容为1.74×10-7J/K,热时间常数为1.33 ms。当红外光源的斩波频率为10 Hz时,钨微测辐射热计的电压响应率为1.91×103V/W,探测率为1.88×107cm·Hz1/2/W。     

基于VB6.0的红外甲烷检测仪串行通信的实现

针对煤矿安全生产中存在的瓦斯爆炸问题,该文以MSP430系列单片机为核心,设计了红外甲烷检测仪.其中着重介绍了检测仪的串行通信,编写了串行通信程序,使检测仪能实现与PC机的数据通信功能,并使用VB6.0编写了人机交互界面,以方便用户及时观察和处理数据,实现对检测仪的校准、复位和阈值设置等操作功能.实验结果表明,编写的串行通信程序能实现检测仪与PC的数据通信功能,检测仪能快速、准确地检测出甲烷气体的浓度,具有较高的实用价值.     

红外线气体分析在合成氨装置中的应用和改造

介绍了红外线气体分析仪的测量原理以及在合成氨装置中的应用情况。对 使用中出现的故障和原因进行了分析,对预处理装置的改造提出了相应的措施。     

TGA analysis of γ‐irradiated linear low‐density polyethylene

Linear low‐density polyethylene (LLDPE), based on butene‐1 or hexene‐1, was irradiated with γ‐rays under vacuum or in the presence of air. The study focused on the influence of the dose rate and the γ‐dose on the thermal properties of LLDPE. Differential scanning calorimetry, thermogravimetric analysis (TGA), and TGA/FTIR techniques were used to address the thermal behavior as a result of γ‐irradiation. During this irradiation, competition between crosslinking and scission reactions, subsequent to oxidation reactions, occurred in the polymeric material, which strongly depends on the experimental conditions. A decrease of the crystallinity for γ‐irradiated samples was observed in particular for samples irradiated under vacuum. This observation may be explained by increased hindrance of segment mobility due to crosslinking reactions that prevent crystal growth. TGA investigations revealed an enhancement of the thermal stability for samples irradiated under vacuum but not for those irradiated in air. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2790–2795, 2006     

水泥中硫的高频红外分析方法研究

采用高频红外吸收法测定了水泥中硫的含量,并对样品作测定前的预处理(物理处理),在测定中选用复合型助熔剂,解决了高频感应炉中因顶吹氧气流的作用而导致的样品喷溅问题。该法可准确测定水泥中0.001％～5％的硫,回收率为98.6％～102.5％,RSD为0.78％～1.35％。