新安江流域安徽省地区水环境状况分析

统计分析流域内点源污染、面源污染产生量与污染物入河量的调查监测数据,结果表明:安徽省辖新安江流域点源入河系数约为面源入河系数2~3倍,点源污染是流域内主要污染来源,但面源污染的作用不容忽视,尤其是总磷,有近2/3来自面源,相对省辖淮河、长江两流域来说,面源污染贡献率明显增大。指出流域污染防治必须综合考虑点、面源污染两个方面;在点源污染不太严重的情况下,对面源污染的治理必须引起足够的重视,才能取得实效。     

Measurement and Identification of the Parameters of SPICE-Models of a Bipolar Transistor

A method of measuring and identifying the static parameters of a bipolar transistor is considered. The characteristic of the transistor, from which the parameters of the model are determined, is chosen depending on what group the calculated parameters belong to. The characteristics are measured in such a way that the equations of the model describing them can be reduced to the simplest form.     

Damage Development in Gray Cast Iron under Static Deformation

The authors discuss the results of experimental investigation of structural degradation of gray cast iron at various stages of static tensile deformation. Analysis of the deformation process has revealed that damageability of a material under loading can be assessed by both a special strain parameter and scatter of hardness characteristics or a ratio of the modulus deviation to the current value of the elastic modulus. A correlation between these parameters has been established.     

基于对地观测激光回波特征的目标特性研究

本文研究了对地观测激光回波特征与地面目标特征之间的关系模型，分析了分类地面目标的激光回波特征，提出一种基于查表法的目标特性计算方法并给出了仿真结果。     

Prediction Model for BTA Deep-Hole Machining using Fuzzy Clustering Approach: Experimental Study

In this article, a subtractive clustering-based fuzzy identification method and a Sugeno-type fuzzy inference system are used for modeling in metal cutting. This approach is considered with its application on the experimental study of Boring and Trepanning Association (BTA) deep-hole drilling. The model for the surface roughness is identified by using the cutting speed and feed as input data and roughness as the output data. Using subtractive clustering in both input and output spaces performs the model-building process. Minimum error model is obtained through enumerative search of clustering parameters. The fuzzy model obtained is capable of predicting the surface roughness for a given set of inputs (speed and feed). Therefore, the operator can predict the quality of the surface for a given set of working parameters and will then be able to set the machining parameters to achieve a certain surface quality. The fuzzy model is verified experimentally by further experimentation using different sets of inputs. The tool life is also investigated using the same approach. The fuzzy inference system obtained is capable of predicting the tool life for a given set of cutting parameters. Therefore, the operator will be able to predict how many minutes the cutting tool is going to last and will set the time for the next tool change.     

Quality Control for Scalable Media Processing Applications

Many media processing applications create a load that varies significantly over time. Hence, if such an application is assigned a lower processing-time budget than needed in its worst-case load situation, deadline misses are likely to occur. This problem can be dealt with by designing media processing applications in a scalable fashion. A scalable media processing application can run in multiple qualities, leading to correspondingly different resource demands. The problem we consider is to find an accompanying quality control strategy, which minimizes both the number of deadline misses and the number of quality changes, while maximizing the quality of processing. We present an initial approach to the above problem by modeling it as a Markov decision process (MDP). Our model is based on measuring relative progress at milestones. Solving the MDP results in a quality control strategy that can be applied during runtime with only little overhead. We evaluate our approach by means of a practical example, which concerns a scalable MPEG-2 decoder.     

现役水工钢闸门结构可靠性鉴定时荷载取值分析

采用类比法确定现役水工钢闸门结构的荷载评估基准期。以静水压力为例，得了其在荷载评估基准期内的统计参数，讨论了闸门主梁受弯碱坏时可靠指标随继续使用期的变化。     

掺Er Al2O3光波导薄膜材料的制备及光学特性

介绍了掺ErAl2O3光波导薄膜的四种典型制备方法的研究结果。比较铒的发光环境和发光特性,分析了影响光致发光强度和寿命的条件和因素。不同工艺制得的Er∶Al2O3薄膜,膜内成分、膜的晶相、掺杂浓度等对Er3 的发光特性均有影响。退火对发光特性及材料具有改善作用。     

浅谈应用标准进行软件测试

国家标准GB T175 44规定了软件包的质量要求及针对这些要求如何对软件包进行测试的细则。质量要求从产品描述、用户文档、程序及数据三个方面进行了规定 ,测试细则依据这些规定制定。ISO IEC912 6 (1991)版由ISO IEC 912 6 (软件产品质量 )和ISO IEC14 5 98(软件产品评测 )两个标准代替 ,ISO IEC912 6表述了软件产品质量的内部质量、外部质量和使用中的质量 ,规定了内部质量、外部质量的六个质量特性 ,并细分为 2 1个子特性 ,使用中的质量规定了四个使用质量特性 ,使用质量是指六个软件产品质量特性的综合效果。进行软件测试时 ,可以依据GB T175 44中的规定组织测试过程再结合ISO IEC912 6中的质量特性及子特性的规定确定测试需求的内容和测试的重点 ,利用ISO IEC912 6质量的规定建立质量评级的标准。     

挤扩支盘桩在湿陷性黄土地基中的应用

湿陷性黄土具有遇水发生湿陷、承载力大幅度降低的性质,这种性质直接影响到基础的承载力。为了研究支盘桩在湿陷性黄土地基中的承载性状,对湿陷性黄土中的3根支盘桩进行预浸水静载荷试验,结果表明,支盘桩荷载—沉降曲线为缓变型,具有较好的承载性能,荷载传递规律与在非湿陷性黄土地基中具有相似的性质,桩身各段承载力的发挥具有明显的顺序性,其结果为挤扩支盘桩在湿陷性黄土地基中的应用提供了依据。