Analysis of Multiphase Flow and Heat Transfer: Pressure Buildup in an Unsaturated Porous Slab Exposed to Hot Gas

This study develops a mathematical model for coupled heat and mass transfer in an unsaturated porous slab exposed to a flowing hot gas. Effects of the initial saturation conditions on associated variables, i.e., total pressure, temperature, moisture content, and multiphase flow, are studied. The Newton-Raphson method based on a finite volume technique is applied. This study emphasizes the influence of initial saturation level and gravitational effect in heat and multiphase flow phenomena associated with this system. Gravity enhances the downward flow of liquid within the porous slab. Pressure buildup occurs near the interface between the wet and the dry zone. However, it appears that the order of magnitude to the total pressure is small. This study explains the fundamental mechanism of multiphase flow that involves heat and mass transfer in a heated unsaturated porous slab.     

Upper bounds for solar thermophotovoltaic efficiency

The main components of thermophotovoltaic (TPV) devices are the primary lens (or mirror), the absorber, the PV cell, and a photon recuperator system. A theory integrating all these components is used in this paper to analyse a particular type of TPV device (plane disk absorber and PV cell). The TPV efficiency is maximized by using three optimization parameters, namely absorber, PV cell temperatures, and cell voltage. Almost ideal operation conditions are envisaged and upper bounds are obtained for the TPV efficiency. They are strongly dependent on PV cell bandgap and radiation concentration. Preliminary results suggest the existence of an optimum solar radiation concentration ratio. The improvement in thermal design quality allows the usage of PV cells based on wide bandgap semiconductors.     

Multi-site phase transfer catalyst assisted radical polymerisation of glycidyl methacrylate using potassium peroxydisulphate as initiator – a kinetic study

In this work, the kinetics and mechanism of free-radical polymerisation of glycidyl methacrylate (GMA) using potassium peroxydisulphate (PDS) as water soluble initiator in the presence of synthesized 1, 4-Bis (tributyl methyl ammonium) benzene dichloride (TBMABDC) as multi-site phase transfer catalyst (MPTC) was studied. The polymerisation reactions were carried out under inert and unstirred conditions at constant temperature of 60 ± 1°C in cyclohexane/water biphase media. The role of concentrations of monomer, initiator, catalyst and volume fraction of aqueous phase, solvent polarity and temperature on the rate of polymerisation (Rp) was ascertained. The order with respect to monomer and initiator was found to be unity. The order with respect to catalyst was found to be 0.51. The rate of polymerisation is independent of ionic strength and pH of the medium. However, an increase in the polarity of solvent has slightly increased the Rp value. Based on the results obtained, a suitable kinetic scheme has been proposed to account for the experimental observations and its significance discussed.     

裂齿矩形翅片板翅式换热器优化设计的分析

对裂齿矩形翅片板翅式换热器中的裂齿矩形翅片的传热效率作了分析,并以单位质量材耗的换热能力最大为目标函数,分析研究了在不同雷诺数(Re)的操作条件下裂齿矩形翅片间角度、翅片厚、长度、宽度及极厚之间的关系。结果表明:在气体换热的场合下,当Re在某一范围时翅片可有效地起到强化传热的作用。当板厚为5mm,翅片厚为3mm,翅片间夹角为45°～70°,Re为2×10~3～8×10~3,最佳翅片纵向间距与翅片长度和翅片厚度乘积的平方根的比为1.5～2.5,最佳翅片尺寸系数为3～5时,传热强化效果较好。     

Research on Marine Boiler＇s Pressurized Combustion and Heat Transfer

The effect of pressure on combustion and heat transfer is analyzed. The research is based on the basic combustion and heat transfer theorem. A correction for the heat calculation method for pressurized furnace is made on the basis of the normal pressure case. The correction takes the effect of pressurizing into account. The results show that the correction is reasonable and the method is applicable to combustion and heat transfer of the marine supercharged boiler.     

MIP-CGP工艺专用催化剂CGP-1的开发与应用

阐述了生产汽油组分满足欧Ⅲ排放标准并多产丙烯的催化裂化工艺（简称MIP-CGP）专用催化剂（简称CGP-1）的研究开发与工业应用结果。CGP-1催化剂的基质具有良好的容炭性能，使活性组元受到良好保护，其优势作用在第二反应区得以充分发挥，具有更高的氢转移活性和强的汽油小分子烯烃裂化活性。中国石化九江分公司和镇海炼化公司的MIP-CGP工业试验标定结果表明，与常规FCC相比，采用CGP-1催化剂的MIP-CGP技术在生产烯烃体积分数小于18％的汽油组分的同时，丙烯产率达到8％以上。此外，汽油诱导期大幅提高，抗爆指数增加；总液体收率有所提高，干气产率下降，焦炭选择性良好。     

Moral value transfer from regulatory fit: What feels right is right and what feels wrong is wrong.

People experience regulatory fit (E. T. Higgins, 2000) when the strategic manner of their goal pursuit suits their regulatory orientation, and this regulatory fit feels right. Fit violation feels wrong. Four studies tested the proposal that experiences of fit can transfer to moral evaluations. The authors examined transfer of feeling wrong from fit violation by having participants in a promotion or prevention focus recall transgressions of commission or omission (Studies 1 and 2). Both studies found that when the type of transgression was a fit violation, participants expressed more guilt. Studies 3 and 4 examined transfer of feeling right from regulatory fit. Participants evaluated conflict resolutions (Study 3) and public policies (Study 4) as more right when the means pursued had fit. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

炼铁生产环境负荷分析和预测研究

利用寿命周期评价的思想，计算了炼铁生产过程中的环境负荷，并分析了各因素对环境负荷的影响，运用神经网络对炼铁生产过程环境负荷进行了预测。     

Measurement of the coolant flow rate using correlation of temperature fluctuations

The transit time of the coolant, and thus its velocity, has been measured using the temperature fluctuation at the outlet of a reactor core. An impulse response function estimation is introduced, which substitutes the widely used cross-correlation measurement technique. It is shown in theory and practice that the time delay estimation is improved when using the impulse response function instead of the cross-correlation function in parameter estimation. Extremely low velocities (down to 2 cm/sec) have been measured in a natural circulation regime in a research reactor.