Comparison of mass transfer efficiency in horizontal rotating packed beds and rotating biological contactors

In this study, the mass transfer efficiencies of a novel horizontal rotating packed (h‐RPB) bed and the conventional disc‐type rotating biological contactor (RBC) were studied at four speeds and seven submergences. Pall rings of two different sizes (25, 38 mm), superintalox saddles and a wiremesh spiral bundle were used as packings in the h‐RPB. Volumetric gas–liquid mass transfer coefficients were determined by unsteady state absorption of atmospheric oxygen in de‐aerated water. Power consumption per unit liquid volume has been found for all geometries tested. The oxygen transfer efficiency values for the h‐RPB were found to be 2–5 kg kWh^?1 and for the disc RBC were found to be 1–2 kg kWh^?1. The performance of the h‐RPB was also compared with other gas–liquid contactors such as surface aerators. The study proves that the h‐RPB is a energy efficient alternative to conventional contactors. Copyright © 2005 Society of Chemical Industry     

非理想截面脊形介质光波导导波模式的研究

提出了一种求解任意截面形状脊形光波导的方法，先利用有效折射率的概念解出某种截面形状脊形光波导的等效折射率，再利用转移矩阵的理论求解出波导的模式色散方程。     

Heat transfer enhancement by Marangoni convection in the NH3–H2O absorption process

The objectives of this paper are to quantify the effect of Marangini convection on the absorption performance for the ammonia–water absorption process, and to visualize Marangoni convection that is induced by adding a heat transfer additive, n-octanol. A real-time single-wavelength holographic interferometer is used for the visualization using a He–Ne gas laser. The interface temperature is always the highest due to the absorption heat release near the interface. It was found that the thermal boundary layer (TBL) increased faster than the diffusion boundary layer (DBL), and the DBL thickness increased by adding the heat transfer additive. At 5 s after absorption started, the DBL thickness for 5 mass% NH₃ without and with the heat transfer additive was 3.0 and 4.5 mm, respectively. Marangoni convection was observed near the interface only in the cases with heat transfer additive. The Marangoni convection was very strong just after the absorption started and it weakened as time elapsed. It was concluded that the absorption performance could be improved by increasing the absorption driving potential (x_vb−x_vi) and by increasing the heat transfer additive concentration. The absorption heat transfer was enhanced as high as 3.0–4.6 times by adding the heat transfer additive that generated Marangoni convection.     

Material state remapping in computational solid mechanics

A computational procedure for remapping material state information from one finite element mesh to another is described. The procedure is useful in connection with evolving meshes for inelastic problems, as for example occur in the context of fracture simulation and adaptive mesh refinement. The proposed method is based on weak enforcement of equality between corresponding fields on the two meshes, where piecewise‐constant fields on both meshes are generalized from the quadrature‐point values. The essential algorithmic problem is that of calculating the volume partition of an arbitrary convex region with respect to a covering set of disjoint convex regions. Instead of geometrically resolving the associated intersections, the problem is herein approximated by a constrained optimization problem, which may be readily and efficiently solved computationally. This formulation is a main contribution of the paper. Computational examples are given that illustrate the effectiveness of the proposed procedure. Copyright © 2002 John Wiley & Sons, Ltd.     

配网侧接入电源对负荷建模的影响

研究了配网侧接入电源对负荷建模的影响。发现当配网侧电源的发电容量逐渐增大时，原有的感应电动机并联恒阻抗、恒电流、恒功率（ZIP）模型的负荷模型将不再能很好地反映该区域的负荷特性，进而提出了一种新的负荷模型结构———异步发电机并联ZIP模型。通过仿真计算，验证了该新负荷模型的有效性，并进一步统一了上述2种负荷模型，称为异步机并联ZIP负荷模型。     

竖直狭缝通道中液氮沸腾强化换热的实验研究

实验表明，狭缝间隙对液氮自然对流核态沸腾换热有明显的影响，在低热流密度下，间隙小的狭缝沸腾换热比间隙大的狭缝明显增强，当狭缝间隙小于实验压力下气泡的脱离直径时，对于同样的热流密度，传热温差减小一个数量级以上，沸腾换热系数提高十几倍到二十倍以上，当热流密度增加一定程度（＞4W/cm^2)时，间隙小的狭缝沸腾换热比间隙大的狭缝有所减弱。     

上海市用电负荷管理系统主站异地冗灾备份方案研究

对上海市用电负荷管理系统主站灾备系统的建设进行可行性研究,根据系统现有结构,结合主流技术提出建议性的方案.重点对各种设备技术进行分析,包括涉及计算机、网络、软件等各方面的设备技术,提出建设原则及实施建议.     

垫层载荷试验应注意的几个问题

介绍了垫层上载荷试验的类型，通过工程实例对不同类型垫层上的载荷试验应注意的问题进行了分析和探讨，这对通过载荷试验确定双层地基承载力具有一定的实际意义，可供同类工程参考借鉴。     

Electro‐optical transfer function preferences for LCD TVs: The effect of display brightness and surround illumination on preferred gamma

Abstract— Recent commercial liquid‐crystal‐display (LCD) televisions are larger and brighter than traditional televisions, thus impacting the viewing conditions in which they are viewed. These changes in viewing conditions may require different electro‐optical transfer functions (EOTFs) for LCD TVs than those for conventional TVs. Here, the way various EOTFs affect the preferred image quality of test images with changes in brightness and surround illumination conditions are examined. The first method used a gain, offset, and gamma (GOG) function with a range of gamma values, and the second method altered the intrinsic EOTFs. Image preference for the simulated EOTFs was determined using a paired‐comparison experiment for ten images. The first experiment took place in a darkened room at two display luminance levels. The results indicated that a gamma of 1.6 was most preferred overall although more so at a lower screen luminance level. In a second experiment, the procedure was repeated with a dim surround of 10% of the display's white point. With this surround, preference for a gamma value of around 1.6 at both screen luminance levels was more enhanced. These results indicated that image preference for different EOTFs is dependent on display luminance and that this dependence is maintained with a dim surround.