金属换热器选用经济分析

本文以系统节能和提高综合经济效益的观点，分析了金属换热器传热系数的影响因素及提高途径；气流阻力与动力消耗；传热面积与投资的定量关系。为正确选用不同结构金属换热器及其性能提供了依据。     

像增强型夜视系统的图像信息传递

在分析了像增强夜视系统信息传递的基础上，指出像增强器输出端荧光屏至人眼的图像传递过程，构成了像增强夜视系统信息传递量的限制．提出了采用系统信息传递量作为夜视系统设计与评价的方法，利用这种方法可以发现在像增强器增益足以补偿光谱选道衰减的条件下，采用彩色像增强可以大幅度增加夜视系统传输的信息量．     

Modeling of Diffusion in Capillary Porous Materials During the Drying Process

This paper presents a model of heterogenous diffusion in capillary porous materials during the process of drying. The governing heat and mass transfer equations have been established using the liquid as well as vapor flow. Two models have been presented. Model 1 does not consider the heat conduction while the model 2 has been established by considering the conduction. The developed models and the numerical solutions of the resulting differential equations can take into account the moisture and temperature dependent thermophysical properties of the product. All equations have been established in spherical coordinates but the programme written for the purpose of calculations can be used for other geometries also. Numerical calculations have been performed for gas concrete and tiles using model 1, while model 2 has been used for gas concrete only because of the lack of data for thermophysical properties of the tile. For gas concrete it was seen that conduction has only marginal effect on the drying process and the numerical predictions of the drying process were reasonably accurate.     

压型钢板组合楼板承载力的有限元分析

压型钢板组合楼板是 2 0世纪发展起来的一种新型结构形式。它具有显著的优势 ,如轻质、高强 ,施工快捷等 ,将在未来的建筑领域中大有作为。组合楼板的承载力主要取决于钢板 -混凝土界面处的抗剪强度。建立了一个二维有限元模型来研究单向组合板的性能。并将计算结果与试验数据进行对比 ,验证了模型的有效性     

Skeletal Isomerization and Inter—molecular Hydrogen Transfer Reactions in Catalytic Cracking

Bimolecular hydrogen transfer and skeletal isomerization the important secondary reac-tions among catalytic cracking reactions,which affect product yield distribution and product quality,Catalyst properties and operating parameters have great impact on bimolecular hydrogen transfer and skeletal isomerization reactions .Bimolecular hydrogen transfer activity and skeletal isomrization activity of USY-containing catalysts are higher thn that of ZSM-5-containing catalyst.Coke deposition on the active sites of catalyst may suppress bimolecular hydrogen transfer activity and skeletal isomer-ization activity of catlys in different degrees.Short raction time causes a decrease of hydrogen trans-fer reaction,but and increase of skeletal isomerization reaction compared to cracking reaction in catalytic cracking process.     

碱式苦味酸铅针刺药的应用研究

提出了以碱式苦味酸铅为主体的针刺药在组合点火管中的应用，并对其针刺药的点火性能及能量传递进行了讨论，阐明了此类针刺药良好性能和应用价值。     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

The influence of the fabrication process on the buckling of thin-walled steel box sections

Steel box sections are usually fabricated from flat plates which are welded at the corners. The welding process can introduce residual stresses and geometric imperfections into the sections which can influence their strength. For some thin-walled sections, large periodic geometric imperfections have been observed in manufactured sections. Subsequent investigations have indicated that the imperfections are in fact buckling deformations i.e. the box section has buckled due to welding residual stresses prior to any application of external load. The welding procedure and the behaviour of the box sections under load has been modelled using a finite element analysis that accounts for both geometric and material non-linearities. Tests have been carried out on box sections with a range of width to thickness ratios for the plate elements. Modelling has been shown to give good correlation with the test results. The conditions for buckling to take place as a result of the welding process have been established. A design method has been proposed.     

大功率UPS的并联控制技术

提出了一种新的N 1三相大功率UPS的并联控制方案，并且在4台40KVA三相在线式UPS上进行了实验研究，实际运行结果证明采用此方法可以获得良好的静态与动态特性。     

Effect of Pressure Gradient on Heat Transfer of Impinging Submerged Circular Jets

An experimental and numerical study have been carried out to investigate the distribution of radial local heat transfer coefficients of impinging submerged circular jets. Good agreement is achieved between the experimental results and the predicted value. Results show that the outer peak usually occurs at the radial location of r/d= 1.8~2.0, in which transition from laminar to turbulence happens resulting from disappeared pressure gradient abruptly, and that the inner peak appears rigidly at r/d=0.5, where the boundary layer has a minimum thickness because of elevating pressure gradient.