无线电引信被干扰率及抗干扰率

本文从无线电引信相对杀伤比率出发，引伸出引信被干扰率及抗干扰率的定义及计算公式。     

Equipment for Testing Sheet Structural Materials under Biaxial Tension. Part 2. Testing by Biaxial Loading in the Plane of the Sheet

We analyze specific features of the design of equipment used for mechanical testing of sheet structural materials under the conditions of biaxial static, cyclic, or dynamic loading. We propose original solutions of the problems related to the fatigue testing of crosslike specimens performed without using complex hydraulic systems and their dynamic testing carried out by using very simple testing machines for uniaxial tension–compression.     

Analytical Calculation of Large-Scale Deflection of Pulse-Loaded Elliptic Plates

Large deflections of pulse-loaded elliptic and round plates made of hardenable elastoplastic materials are investigated analytically using an energy-based approach. Formulas that are convenient for engineering design have been derived.     

GH2027铁基高温合金的第二相研究

运用电子显微分析和波谱分析等方法对ＧＨ２０２７合金的第二相进行了研究，结果表明，合金晶界相主要是片状Ｍ６Ｃ和薄膜状Ｍ２３Ｃ６，经波纹图样测得其错配度约为３％，晶内Ｍ６Ｃ和Ｍ２３     

光孤子相互作用对压缩态的影响

在线性近似条件下，量子化了非线性薛定谔方程，用后向传播法数值求解了光孤子相互作用对压缩比的影响。数值结果表明，在碰撞距离附近，压缩比显著增加。     

结构陶瓷的高温疲劳强度衰减理论

提出了陶瓷材料疲劳强度衰减理论并由此导出了各种疲劳关系式。建立了疲劳基本方程ｄσ＿ｒ／ｄ＿ｉ＝一Ａσ（ｔ）￣ｎｔ￣（－ｍ），得出了疲劳寿命公式Ｔ＝Ｍ（σ＿０－σ）／Ａσ￣ｎ（静疲劳时Ｍ＝１，连续增载疲劳时Ｍ＝ｎ＋１，循环疲劳时Ｍ＝（ｎ＋１）／（１＋Ｒ＋Ｒ￣２＋……＋Ｒ￣ｎ），逐级加载时，并导出不同疲劳方式下疲劳寿命间的关系。同时，用多种Ｓｉ＿３Ｎ＿４材料在高温中作了论证试验，结果与理论一致。     

高效防气防砂一体化管柱的研制与应用

为解决文南油田高气液比井出砂易造成卡泵的问题,研制了高效防气防砂一体化管柱。该管柱主要由闭式气锚、重力式防气装置和激光割缝筛管3部分组成。闭式气锚的分离作用消除了气体对抽油泵的影响,提高了泵效;重力防气装置利用液气分离原理和高烟囱原理进行液气分离,液流回流时间可达10min,排气最高压差可达0.2MPa;经激光割缝筛管过滤后的液体含砂粒外径小于0.05mm。该管柱在文南油田现场应用16井次,累计增液6000t,增油2717t,平均单井泵效提高7%。     

用试井方法确定注水后地层渗透率的变化

大港油田已进入开发中后期，高含水油田占73％，开发初期的一些参数已不适合现在开发的需要。研究出一套用试井方法确定注水以后地层渗透率变化的方法，对大港油田的增储上产具有重要意义。     

On the hollowness ratio effect on the dynamics of a spinning Rayleigh beam

The analytical solutions of a spinning Rayleigh beam with rotatory moment inertia and gyroscopic effect are presented in this paper. The critical speeds can be written analytically in a function of the length-to-radius ratio (l) defined by the beam's length over its outer radius and the hollowness ratio (α) defined by the hollow area over the total area of the cross section. The sensitivity analyses show that the critical speed is decreasing with l, but increasing with α. Moreover, α is more sensitive to the critical speeds. The design of a spinning beam should therefore be emphasized more on the hollowness factor. Contrary to common belief, only finite critical speeds exist and the number is independent of the boundary conditions. It increases monotonically with l, but decreases with α. The steady state unbalanced response can therefore be expressed analytically by the finite precessional modes and the corresponding generalized coordinates.