混流式水轮机转轮简化模型焊接应力场的数值模拟

在确定混流式水轮机转轮简化模型、解决分段焊焊接热源加载问题及解决各独立实体间接触边界节点不重合的热传导问题的基础上,对转轮模型焊接过程的应力场进行了数值模拟.得到了焊接过程中纵向应力的演变规律与焊后应力场的分布情况.结果表明,焊后应力峰值出现在叶片与上冠或叶片与下环接触面附近.该结果可以较好地解释水轮机转轮叶片疲劳裂纹的产生和扩展的失效行为.     

Identification of plant model of linear induction motors for a traction system intended for use in a high‐performance controller

A linear induction motor (LIM) is suitable for use in trains. The motor can be used in both wheel‐suspended and contact‐less types such as the Linear Metro and HSST trains in Japan. The LIM has end winding as well as asymmetrical winding. The end effect is a major problem in the LIM, and it makes the analysis, design, and control of motors difficult. This paper describes a method that combines numerical analysis and the equivalent circuit for the LIM in order to design a high‐performance controller for the LIM that includes the end effect. A sample basic field‐oriented control scheme that is based on the plant model is applied to the LIM in order to check the control performance. The theory of rotary induction motors is used for verification. © 2012 Wiley Periodicals, Inc. Electr Eng Jpn, 179(2): 44–54, 2012; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21171     

Transient phenomena of current and field distortion due to dynamics of packet‐like charges in LDPE films

Simultaneous measurements of space charge and external current were carried out using a PEA measurement system with an electrometer on the back of a grounding electrode in order to clarify the physical situation of a huge packet of positive space charges in LDPE films. A large number of positive charges from a semiconducting anode were accumulated at the interface between LDPE and an Al‐cathode at a mean applied field of 1.5 MV/cm and then finally disappeared. The results of simultaneous measurements showed that the external current kept a relatively high value during charge accumulation and further increased when the charges disappeared. Both the charge dynamics and the external current were restricted by addition of a low‐molecular‐weight paraffin wax, indicating that carrier transport was influenced by the microstructure of the polymer. The dynamics of the residual charges after short‐circuiting is also discussed. © 2012 Wiley Periodicals, Inc. Electr Eng Jpn, 179(4): 10–17, 2012; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21256     

生物质与煤混烧特性的数值模拟研究

针对生物质与煤混烧影响锅炉经济燃烧特性现象,笔者采用处理软件Gambit建立锅炉流场空间网格物理模型,利用Fluent模拟混烧过程并对其数学模型进行求解,模拟混烧过程,并根据长春某电厂生物质混烧参数,计算分析了不同混烧比时的锅炉炉内流场与温度场变化,得出了不同混烧比例下炉内燃烧流场、温度的变化规律.计算结果表明,随着生物质与煤混烧比例的提高,炉内流场动力特性无明显变化,但炉内燃烧温度下降比较明显.     

Parametric models of local search progression

Algorithms that search for good solutions to optimization problems present a trace of current best objective values over time. We describe an empirical study of parametric models of this progression that are both interesting as ways to characterize the search progression compactly and useful as means of predicting search behavior. In our computational experiments, we give examples of a variety of problems and algorithms where we are able to use the parametric models to make predictions of performance that cross instances and instance sizes.     

A Study on SSVEP-Based BCI

Abstract-Brain-computer interface （BCI） can help the deformity person finish some basic activities. In this paper, we concern some critical aspects of SSVEP based BCI, including stimulator selection, method of SSVEP extracting in a short time, stimulating frequency selection, and signal electrode selection. The conclusion is that the stimulator type should be based on the complexity of the BCI system, the method based on wavelet analysis is more valid than the power spectrum method in extracting the SSVEP in a short period, and the selections of stimulating frequency and electrode are important in designing a BCI system. These contents are meaningful for implementing a real SSVEP-based BCI.     

Design and Fabrication of a Movable Langmuir Probe for Plasma Edge Parameters Measurement in the IR-T1 Tokamak

For the edge plasma parameters measurement, a movable Langmuir probe is fabricated and installed on the IR-T1 tokamak. The set-up consists of two sets of single Langmuir probes with tungsten tip movable in the radial direction. Edge plasma parameters including electron temperature, Ion density, floating potential and the corresponding radial changes are measured. Using two-point correlation technique clearly reveal that in the SOL region the poloidal propagation of floating potential fluctuation is in the direction of ion diamagnetic drift and in the edge it propagates in the electron diamagnetic drift direction.     

Theory of electrostatics and electrokinetics of soft particles

We investigate theoretically the electrostatics and electrokinetics of a soft particle, i.e. a hard particle covered with an ion-penetrable surface layer of polyelectrolytes. The electric properties of soft particles in an electrolyte solution, which differ from those of hard particles, are essentially determined by the Donnan potential in the surface layer. In particular, the Donnan potential plays an essential role in the electrostatics and electrokinetics of soft particles. Furthermore, the concept of zeta potential, which is important in the electrokinetics of hard particles, loses its physical meaning in the electrokinetics of soft particles. In this review, we discuss the potential distribution around a soft particle, the electrostatic interaction between two soft particles, and the motion of a soft particle in an electric field.     

Qualitative and quantitative assessment of interior moisture buffering by enclosures

The significance of interior humidity in attaining sustainable, durable, healthy and comfortable buildings is increasingly recognised. Given their significant interaction, any interior humidity appraisal requires a qualitative and/or quantitative assessment of interior moisture buffering. While the effective moisture penetration depth and effective capacitance models allow quantified assessment, their reliance on the ‘moisture penetration depth’ necessitates comprehensive material properties and hampers their application to multidimensional interior objects. On the other hand, while various recently suggested protocols for the simple and fast measurement of the moisture buffer potential of interior elements allow qualitative assessment, none of these are currently dependable for a wide range of moisture production regimes.In response to these flaws, this paper introduces the production-adaptive characterisation of the moisture buffer potential of interior elements and corroborates their superposition toward a room-enclosure moisture buffer potential. It is verified that this enables qualitative comparison of enclosures in relation to interior moisture buffering. It is moreover demonstrated that it forms an alternative basis for quantitative evaluation of interior moisture buffering by the effective moisture penetration depth and effective capacitance models. The presented methodology uses simple and fast measurements only and can also be applied to multimaterial and/or multidimensional interior elements.