Corner forming of AZ61A magnesium alloy tube within warm hydroforming

The corners with small radii on cross sections are crucial for forming hydroformed components with polygonal sections.In this paper,warm hydroforming experiments of AZ61A magnesium alloy tubes were carried out to study the forming regularity of round corners by using a demonstration part with square sections.Effects of temperature on radius forming,thinning ratio distribution and microstructure were revealed and a component with relative outer corner radius of 3.0 was obtained by warm hydroforming at 240℃.The minimum thickness of the formed square section was located in the transition position between the corner and the straight wall.The thinning ratio of the round corner increased with the increase of forming temperature.Formability of the magnesium tube was improved by raising temperature under the effect of dynamic recrystallization at 240℃.     

相关分析在QC小组活动中的应用

QC小组将安阳卷烟厂2007年7月的质量报表中＂松散回潮工序后室温度过程能力指数小于1.33＂,不能满足要求的问题作为研究课题,通过现状调查,并将调查数据绘在散布图上,利用散布图了解到松散回潮工序前室温度标偏和后室温度标偏之间具有高度的线性相关,通过相关分析,确定了前室温度波动大是影响后室温度波动大的症结.通过实施相关对策使后室温度的过程能力指数满足要求.通过相关分析不仅准确地找出了问题的症结,而且提升了QC成果的水平.     

铒离子注入晶体硅的射程分布和离散研究

用400 keV能量的铒离子垂直注入晶体硅(Si)样品中。利用卢瑟福背散射技术研究了能量为400 keV、剂量为5×1015ions/cm2的铒离子注入Si晶体的平均投影射程、射程离散和深度分布。测出的实验值和TRIM 98得到的理论模拟值进行了比较,发现实验值跟TRIM 98模拟计算的理论值符合较好。     

配电网金属氧化物避雷器的选择

文章阐述了配电网金属氧化物避雷器选择的基本内容,给出了选择结果.     

企业价值链价值分配的优化研究

为研究价值链中各企业间价值合理分配的问题,在明确企业价值链中各参与者关系的基础上,从价值分析和成本分析入手,针对价值链中各参与者的不同行为模式,对企业价值链的稳定性问题和价值链调整的合理性问题进行了分析,并给出了价值链稳定性及调整合理性的判定公式和相应经济学解释.阐述了在价值贞献和价值分配之间产生偏差的原因和几种情况,依据博弈论原理建立了价值链价值分配议价模型,模型分析表明存在唯一的子博弈完美均衡,最终可以得到一个均衡策略.研究结果为合理构建和调整企业价值链提供了理论依据.     

Change in the molecular weight distribution of poly(ethylene oxide) caused by the complexation with poly(acrylic acid)

The complexation between poly(ethylene oxide) (PEO) and poly(acrylic acid) (PAA) was made by using double the molar quantity of either polymer component at pH 2 where the resulting complex completely precipitates. After the removal of the precipitate, PEO or PAA remaining in the supernatant was subjected to gel permeation chromatography to investigate the change in the molecular weight distribution (MWD) caused by the complexation. No remarkable difference is observed in the MWD curves for PEO[1] (M_w=1.37 × 10⁴) before and after the complexation with PAA[1] (M_w=1.10 × 10³) and PAA[2] (M_w=4.16 × 10⁵). However, the MWD curves of PEO[2] (M_w=1.26 × 10⁵) and PAA[2] become shortened and shift to the low molecular weight side after the complexation with PAA[1] or [2] and PEO[2], respectively. This tendency is enhanced by increasing the complexation temperature. From these results, it is indicated that the complexation between PEO and PAA deals with an equilibrium reaction, and the equilibrium constant is dependent on the chain length of both polymer components and also on the complexation temperature.     

Gel chromatographic investigation of p-benzoquinone and styrene products copolymerized in the presence of BF3·OEt2

The molecular weight distribution of copolymers of p-benzoquinone and styrene was studied by g.p.c.. It was shown that the products synthesized have low molecular weights and narrow MWD. p-Benzoquinone was found to be a copolymer macromolecule regulator.     

气升式内环流反应器中油滴的分散特性

本文研究了气升式内环流反应器中油滴的分散特性。以对数正态分布密度函数为油滴尺寸的分散模型,导出了油滴的Sauter平均直径解析式。对模型作了实验验证,关联了模型参数。提出了油滴的尺寸分布密度函数和Sauter平均直径的半经验式。结果表明计算值与实验值吻合良好。     

不同线密度粘胶原丝及其碳纤维的结构性能对比

用Weibull分析处理 10mm长的 4种不同线密度粘胶原丝和相应碳纤维的单丝断裂强度 ,得到原丝线密度、强度分布和碳纤维强度的对应关系。采用透射电镜 (TEM )和小角X散射 (SAXS)分析粗旦原丝 ,发现孔洞较多 ,并存在大于 70nm的大孔洞。截面和表面照片也揭示出细旦原丝截面相对规整 ,表面较光滑 ,粗旦原丝则反之。结果表明 ,原丝线密度小 ,截面形状圆整 ,缺陷少 ,所制得的碳纤维强度高。