Progressive damage modelling of SMC composite materials

The present work deals with the modelling of damage behaviour for sheet moulding compound (SMC) composite materials using a finite element analysis package. Specifically, a comparison is made between the results obtained experimentally for a three-point bending test, and those obtained from numerical simulation using a material model already implemented. The simulation has been performed for the material models available within the PAM-CRASH software. The simulation results are compared and validated with respect to experimentation.     

Extracting Light from Polymer Light‐Emitting Diodes Using Stamped Bragg Gratings

In this paper, we describe a method for increasing the external efficiency of polymer light‐emitting diodes (LEDs) by coupling out waveguided light with Bragg gratings. We numerically model the waveguide modes in a typical LED structure and demonstrate how optimizing layer thicknesses and reducing waveguide absorption can enhance the grating outcoupling. The gratings were created by a soft‐lithography technique that minimizes changes to the conventional LED structure. Using one‐dimensional and two‐dimensional gratings, we were able to increase the forward‐directed emission by 47 % and 70 %, respectively, and the external quantum efficiency by 15 % and 25 %.     

Platinum Binuclear Complexes as Phosphorescent Dopants for Monochromatic and White Organic Light‐Emitting Diodes

Efficient blue‐, green‐, and red‐light‐emitting organic diodes are fabricated using binuclear platinum complexes as phosphorescent dopants. The series of complexes used here have pyrazolate bridging ligands and the general formula C^∧NPt(μ‐pz)₂PtC^∧N (where C^∧N = 2‐(4′,6′‐difluorophenyl)pyridinato‐N,C^2′, pz = pyrazole ( 1 ), 3‐methyl‐5‐tert‐butylpyrazole ( 2 ), and 3,5‐bis(tert‐butyl)pyrazole ( 3 )). The Pt–Pt distance in the complexes, which decreases in the order 1 > 2 > 3 , solely determines the electroluminescence color of the organic light‐emitting diodes (OLEDs). Blue OLEDs fabricated using 8 % 1 doped into a 3,5‐bis(N‐carbazolyl)benzene (mCP) host have a quantum efficiency of 4.3 % at 120 Cd m^–2, a brightness of 3900 Cd m^–2 at 12 V, and Commission Internationale de L'Eclairage (CIE) coordinates of (0.11, 0.24). Green and red OLEDs fabricated with 2 and 3 , respectively, also give high quantum efficiencies (～ 6.7 %), with CIE coordinates of (0.31, 0.63) and (0.59, 0.46), respectively. The current‐density–voltage characteristics of devices made using dopants 2 and 3 indicate that hole trapping is enhanced by short Pt–Pt distances (< 3.1 Å). Blue electrophosphorescence is achieved by taking advantage of the binuclear molecular geometry in order to suppress dopant intermolecular interactions. No evidence of low‐energy emission from aggregate states is observed in OLEDs made with 50 % 1 doped into mCP. OLEDs made using 100 % 1 as an emissive layer display red luminescence, which is believed to originate from distorted complexes with compressed Pt–Pt separations located in defect sites within the neat film. White OLEDs are fabricated using 1 and 3 in three different device architectures, either with one or two dopants in dual emissive layers or both dopants in a single emissive layer. All the white OLEDs have high quantum efficiency (～ 5 %) and brightness (～ 600 Cd m^–2 at 10 V).     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

原油基压裂液研究

研制了一种适用于低压、低渗、水敏性储集层的新型原油基压裂液体系。根据基液原油的组分合成相应的增稠剂，增稠剂在原油中与交联剂反应，形成网状结构，使原油成为黏度可以调控的冻胶，从根本上改变了油基压裂液以柴油、煤油为基液的现状，降低了油基压裂液的成本，同时还提高了压裂液的抗温、抗剪切和破胶性能，并将交联时间缩短到2h以内，可以满足现场压裂施工的要求，大大降低了施工强度和压裂改造的综合成本。在青海油田进行的现场先导试验取得成功。图9表1参5     

An Analysis of Citation Counts of ETRI‐Invented US Patents

From its foundation until 2004, ETRI has registered over 1,000 US patents. This letter analyzes the characteristics of these patents and addresses the explanatory factors affecting their citation counts. For explanatory variables, research team related variables, invention specific variables, and geographical domain related variables are suggested. Zero‐altered count data models are used to test the impact of independent variables. A key finding is that technological cumulativeness, the scale of invention, outputs in the electronic field, and the degree of dependence on the US technology domain positively affect the citation counts of ETRI‐invented US patents. The magnitude of international presence appears to negatively affect the citation counts of ETRI‐invented US patents.     

电子产品研制阶段可靠性增长试验研究

结合工程实际经验,深入讨论了可靠性增长过程及实现途径,在保持试验条件和改进过程不变的条件下,实施了对具体型号电子产品的可靠性增长试验,达到了预期的可靠性增长目标,并且利用可靠性增长试验的数学模型(AMSAA模型)来评估产品的可靠性增长,对开展可靠性增长与可靠性增长试验工作具有重要的实际意义.     

堆石料与基岩面直剪试验

介绍了堆石料与基岩面的现场直剪试验方法，6个组次的直剪试验结果表明，堆石料与基岩面的抗剪强度指标随基岩面坚硬度的增大而增加，并随基岩面粗糙度的加大而加大。